Skip to the record
Every meeting, every word.

Original source · versioned page text

SUPERSEDED Compiled Plans OPW20/0145.02

of 205

Page text shows just the words. Original shows the document exactly as it was published.

Page text read automatically using OCR, there may be inaccuracies

Very large file: it may take a few minutes

The original of this document is very large (48.8 MB). Opening the original or downloading it may take a few minutes. Please be patient and don't click again. The page text is quick to read. If you are on mobile data, it is best to wait until you are on Wi-Fi.

Original PDF page 112, section 1. The text section number identifies this passage in the reader.

Plans and drawings

This document appears to be plans or drawings. Its page text below holds only the words printed on the drawings, without the drawings themselves, so it may be jumbled or hard to follow. To see the plans as drawn, choose Original above or download the file (both need you to log in).

Log in to see the plans as drawn
Process Descriptions

 Removal                  Complete tree removal leaving stump as close as possible to ground level. Process will include chipping of
                          all foliage limbs and timber and re-instatement of work site. Recommendation typically based on tree
                          being assessed as representing a health and safety concern [Dead, dying, structurally unsound, unstable,
                          poor form].

 Remove and Grind         Complete tree removal to include grinding of stump to a depth of 75 millimetres unless otherwise
                          specified. Process will include chipping of all foliage limbs and timber and reinstatement of work site.
                          Stump site will be cleaned of all grinding debris and sawdust and backfilled with premium topsoil free from
                          weeds.

 General Pruning          Pruning process will include removal of broken, crossing, rubbing, diseased, stressed or dying branches or
                          limbs with poor attachment. Additional work process will include pruning to define leaders, balance the
                          crown, reduce the weight load or clear the tree from obstructions. In summary, to rectify, as far as is
                          possible, any structural defects and eliminate undesirable growth.

 Canopy Lift / Raise      Pruning process will be restricted to raising of the tree’s lower canopy to a height specified the defaulted
                          parameters will be to provide 2.5 metres clearance from ground level. From time to time pruning
                          requirements may be altered to accommodate various factors such as view, light penetration, vehicle
                          thoroughfare etc and consulting arborist will advise accordingly.

 Remedial Pruning         Pruning process will encompass crown restoration and remedial works where the tree has been previously
                          lopped or otherwise damaged. Not feasible when tree has extensive decay and should only be considered
                          when there is evidence of healthy regrowth. When performed correctly, the process of remedial pruning
                          will most likely take several years to complete.

 Hanger Limb              Pruning process will be restricted to the removal of any hangers or dangerous/dead/dying limbs and will
                          typically involve the removal of a single limb. In some instances, removal of an individual limb may be
                          necessary to accommodate an obstruction and the consulting arborist will advise accordingly.

 Directional Pruning      Pruning process will be restricted to pruning canopy away from buildings/service wires/property boundary
                          and will typically be performed to avoid future growth in these areas [where necessary clean trunking of
                          undesirable growth]. Where appropriate future growth will be directed away from obstruction selecting
                          new leaders.

 Boundary Pruning         Pruning process will involve pruning of tree back to tree owners’ boundary. In every situation every effort
                          should be made to obtain the relevant authorisation to perform pruning to Australian Standards and to
                          avoid “lopping” limbs to the immediate boundary. As with directional pruning, optimum results will be
                          achieved when it’s feasible to eliminate undesirable growth and direct future growth. If authority to enter
                          and work in neighbouring property is not forthcoming processes will be restricted to access on clients
                          property and work standards will be appropriately comprised. Consulting arborist will duly advise client as
                          appropriate.




Arborist Report for 28 Eenie Creek Road, Noosaville
Prepared by Arbor Operations – July 2020
                                                                                                                           15 | P a g e
Log in to download the original file

SUPERSEDED Compiled Plans OPW20_0145.02.pdf · 48.8 MB (very large file)

Very large file: the download may take a few minutes. If you are on mobile data, it is best to wait until you are on Wi-Fi.

Searchable page text hides email addresses. Original files are unchanged and may show email addresses.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.