Council archive · source document
Consolidated Plans - OPW25 0057 (As Published) · OPW25/0057
Plans and drawings: the text below has words only, no drawings.
Very large file (23.1 MB): may take a few minutes to open.
Original PDF page 45, section 1. The text section number identifies this passage in the reader.
1 Beveled top as dimensioned
90 190 2 5mm chamfer to all edges
3 Quality rough sawn HWD 90mm x
50 190mm x 1500mm H4 dipped, F14
75
1 1 Beveled top as dimensioned 1 1 ACQ treated bollards @ 1500mm
2 5mm chamfer to all edges centres. Apply 2x coats of clear
3 Quality rough sawn HWD 90mmx 2 2 Tanacoat prior to installation.
190mmx1500mm H4 dipped, F14 4 400x500mm deep concrete footing to
ACQ treated bollards @ 1500mm Engineer's specifications.
centres. Apply 2x coats of clear 5 Drainage layer nominal 10-20mm
Top of sleeve to be no greater
3 3
Tanacoat prior to installation. 6 Existing sub-grade
than 100mm above FSL
4 400mmØx500mm deep concrete 7 Kerb side
footing to Engineer's specifications. 8 140x20mm diameter steel rod pin with
900
2
7 padlock hole face
825
5 Post to continue through footing 7
into gravel drainage layer nominal 9 RHS hot dip galvanised section sleeve
3 10-20mm to fit 90x190mm HWD bollard without
6 Existing sub-grade having to cut bollard
7 Kerb side face 10 300x200x4mm HDG steel base plate
with 5x20mmØ drainage holes drilled
1500
7 8 11 NSC to supply padlock and key
11
F.S.L. F.S.L. F.S.L. F.S.L.
4
9 9
4 4
5 10 10
5 5
6 6 6
Bollard Type X to match specifications noted on Dwg. All timber products to have Forest Stewardship
BL-01 from SCC Open Space Infrastructure Manual Council® (FSC®) Chain of Custody certification
June 2017
All timber products to have Forest Stewardship
Council® (FSC®) Chain of Custody certification
8 BEVELED HARDWOOD BOLLARD - B1 Type 1 9 BEVELED HARDWOOD REMOVABLE BOLLARD - B2 Type 1
L501 Scale 1:10 L501 Scale 1:10
Turf as specified to finish flush with
timber edge. Refer to Turf Profile
Detail.
Planting area to finish flush with
timber edge
Dressed 25x100mm / 38x100mm
Spade cut garden edge
H4 treated (not CCA) hardwood 75°
to be cut at
edge. 5mm chamfer to all edges approximately 75°
fixed with 75mm galvanised batten angle and run 100mm
screws through pilot hole. deep into soil
100
Treated Timber Stake min. 600mm
x 50mm x 50mm
Existing Subgrade
All timber products to have Forest Stewardship Existing subgrade
Council® (FSC®) Chain of Custody certification
10 MOWING EDGE TYPE 2 - TIMBER EDGING 11 MOWING EDGE TYPE 1 - SPADE CUT
L501 Scale 1:10 L501 Scale 1:10
-
APPROVED PLAN
OPW25/0057
NOOSA COUNCIL
20 AUG 2025
Approved by: James Oliver (AILA)
Checked - JO F 03.07.2025 MCU RFI AMENDMENTS JO
Drawing title - Project - Site - Project No. 233467 Sheet No. L601
Design - JO Drawn - JO
E 17.04.2025 SPECIES CHANGE JO
LANDSCAPE DETAILS Proposed 1 into 3 Development 62 Lake MacDonald Drive, Cooroy
D 24/03/2025 UPDATED PROJECT NAME AR Digital Ref : Issue : F
C 12.03.2025 FOR APPROVAL JO
Scales - AS SHOWN B 24.09.2024 FOR APPROVAL IL 124 DUPORTH AVENUE Ph (07) 5443 7777 Client - This Document is copyright and shall not be copied
PO BOX 16 Fax (07) 5443 7577 without written approval, nor shall it be used except
Document Stage - FOR APPROVAL
A 31.05.2024 PRELIMINARY - FOR COORDINATION ONLY JO
MAROOCHYDORE QLD 4558 Noosa Council for the Development and the Site Specified.
Issue Date Description By E-MAIL: [email protected]
Document Set ID: 24237370
23931061
Version: 1, Version Date: 21/10/2025
15/07/2025
See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalUsed in these records
Consolidated Plans - OPW25 0057 (As Published)Related documentApplication case desk ↗
About this file
- File size
- 23.1 MB (very large file)
- File type
No other editions are linked here.
Original file
Log in to download the original file
The download may take a few minutes. On mobile data, it is best to wait for Wi-Fi.