Original source · versioned page text
Reference Document - MCU24-0118 & OPW24-0140
Form 15 Compliance certificate for building design or specification
This form is the approved form that must be used in accordance with section 10 of the Building Act 1975 and sections 73 and
77 of the Building Regulation 2021 (Design-specification certificate) stating that an aspect of building work or specification will, if
installed or carried out as stated in this form, comply with the building assessment provisions.
REFERENCE DOCUMENT
Additional explanatory information is included in the Appendix at the end of this form. MCU24/0118 & OPW24/0140
NOOSA COUNCIL
4 OCTOBER 2024
1. Property description
This section need only be completed if details of street address and property description are applicable.
E.g. in the case of (standard/generic) pool design/shell manufacture and/or patio and carport systems this section may not be
applicable.
Where applicable, the description must identify all land the subject of the application.
The lot and plan details (e.g. SP/RP) are shown on title documents or a rates notice.
If the plan is not registered by title, provide previous lot and plan details.
Street address 69 Shorehaven Drive
Suburb/locality Noosaville
State QLD Postcode 4566
Lot and plan details (attach list if necessary)
Lot 459 RP 868304
Local government area the land is situated in
Noosa Shire Council
2. Description of aspect/s certified
Clearly describe the extent of work covered by this certificate, e.g. all structural aspects of the steel roof beams.
The following structural elements associated with the new private domestic jetty:
• Hardwood timber framing: decking;
• Aluminium framing arrangement and associated stainless steel fixings & hold-down anchors.
Exclusions:
• Concrete pile design certification by others (refer to Reference Documentation below);
• Individual aluminium TrackDeck member design certification by others (refer to Reference Documentation below).
All methods of construction including temporary bracing and propping; existing structures on the site, including the existing
revetment wall.
3. Basis of certification
Detail the basis for giving the certificate and the extent to which tests, specifications, rules, standards, codes of practice and
other publications were relied upon.
AS1170 SAA Loading Codes – current editions in 2024
AS1720.1-2010 Timber structures – Design methods
AS1664-1997 Aluminium structures
AS2159-2009 Piling – Design & installation
AS3600-2018 Concrete structures
AS4997-2005 Guidelines for the Design of Maritime Structures
The Coastal Protection and Management Regulation 2017: relevant Parts and Schedule 3
Document Set ID:
Building 23227616
Regulation 2021 • Section 73 and 77 • Form 15 • Version 2 • March 2023 Page 1 of 5
Version: 1, Version Date: 06/09/2024
See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalFull text of the other 4 pages
Page 2
4. Reference documentation
Clearly identify any relevant documentation, e.g. numbered structural engineering plans.
Long View Consulting Engineers Drawings issued 17 February 2024:
- 21.101-001 69 Shorehaven Dr Jetty_C2: [S00 – S02] inclusive;
- TJS-04957-01 Site Plan & Water Allocation;
- TJS-04957-02 Layout Plan
- TJS-04957-03 Elevations
- TJS-04957-04 Jetty Details: Sub-Frame Using Trackdeck System
- TJS-04957-05 Joist & Bearer Details
- TJS-04957-06 Pile Setout
Edge Consulting Engineers Drawing:
- JSP-SD-045 Standard Detail – Concrete Insitu Pile Construction Ø315 & Ø400 Reinforced
Projex Partners Consulting Engineers Drawings TrackDeck Product Guide issued 09/08/2024:
- D-TJS-SD-02-TD-01 Cover Sheet
- D-TJS-SD-02-TD-02 Preface
- D-TJS-SD-02-TD-03 Notes
- D-TJS-SD-02-TD-04 Members – Bearer
- D-TJS-SD-02-TD-05 Members – Joist
- D-TJS-SD-02-TD-06 Brackets
- D-TJS-SD-02-TD-07 Standard Configuration
- D-TJS-SD-02-TD-08 Joist And Bearer Splice Details 1
5. Building certifier reference number and building development approval number
Building development
Building certifier reference
application number (if
number
available)
6. Appointed competent person details
Under Part 6 of the Building Regulation 2021 a person must be assessed as a competent for the type of work (design-
specification) by the relevant building certifier.
Name (in full) Freeman McGrath
Company name (if applicable) Long View Consulting Engineers
Contact person
Business phone number Mobile 0414 681 676
Email address [email protected]
Postal address PO Box 963
Suburb/locality Cooroy
State QLD Postcode 4563
Licence class or registration
RPEQ
type (if applicable)
Licence or registration number
19951
(if applicable)
7. Signature of appointed competent person
This certificate must be signed by the individual assessed and appointed by the building certifier as competent to give design-
specification help.
Signature Date 5/09/2024
Document Set ID:
Building 23227616
Regulation 2021 • Section 73 and 77 • Form 15 • Version 2 • March 2023 Page 2 of 5
Version: 1, Version Date: 06/09/2024
Page 3
LOCAL GOVERNMENT USE ONLY
Date received Click or tap to enter a date. Reference number/s
Appendix – explanatory information
IMPORTANT NOTE: It is an offence for a competent person to give a building certifier a document, including this form, that the
person knows or reasonably suspects, is false or misleading.
Who can complete this certificate? (section 10 of the Building Act 1975 (Building Act) and 73 and 77 of the Building
Regulation 2021 (BR 2021).
A building certifier can accept from a competent person (design-specification) a certificate stating that the competent person has
assessed the building design or specification for the aspect of building work, and it will, if installed or carried out under the
certificate, comply with the building assessment provisions, including any relevant standards and codes.
Schedule 10 of the BR 2021 defines building design or specification as any material, system, method of building or other thing
related to the design of or specifications for building work.
When completing the certificate, a competent person is required under section 77 of the BR 2021 to include the basis for giving
the certificate and state the extent to which the competent person has relied on tests, specifications, rules, standards, codes of
practice or other publications.
What is the purpose of this form? (section 10 of the Building Act and sections 73 and 77 of the BR2 2021)
The information in this form informs the building certifier’s decision making when they are assessing a building development
application, issuing the building development approval for the building work the subject of the certificate (form) and when
amending the building development approval due to the receipt of updated aspect information such as glazing or truss
specifications or revised excavation drawings.
Can a manufacturer or supplier give this Form 15?
A building certifier can accept this form from a manufacturer or supplier who the certifier has decided is a competent person
(design-specification).
A manufacturer or supplier of building materials can give this form if they have undertaken the design component for the
product. For example a window manufacturer who designs, constructs and supplies the windows to industry could give this
form.
Competent person (section 10 of the Building Act 1975 and Part 6 of the BR 2021)
A building certifier must assess and decide to appoint an individual as a competent person before they can accept design-
specification help.
When deciding whether a person can be a competent person, the building certifier must assess the person having regard to
their experience, qualifications and skills and ensure the person holds a licence or registration if required.
The building certifier is required to keep detailed records about what was considered when appointing a competent person.
For further information about assessment of someone as a competent person refer to the Guideline for the assessment of
competent persons.
What is required if a manufacturer or supplier did not do the design work for the product?
A manufacturer or supplier who is not part of the design process may give the construction contractor, builder, competent
person or the building certifier evidence of suitability such as a product technical statement under Part A5 of the Building Code
of Australia (BCA), for an aspect or material stating that it is compliant with the relevant reference documents in the BCA i.e. the
applicable Australian Standard/s.
What if there is not enough space for all the supporting material/documents?
Items 2, 3 and 4 requires the competent person to clearly identify the extent of the assessment that was undertaken for aspect/s
of work identified in this form.
For instance, there is provision for material such as specifications, standards, codes or other relevant publications to be
referenced in the form. However, if the space in the form is not sufficient to accommodate all of this material, you can create and
refer to additional material in an addendum or attachment to the form.
The form is the Microsoft Word version, that you can download and edited to include additional material in the relevant parts of
the form. Note: that editing the form in the Microsoft Word version may cause the relevant boxes to expand and increase the
Document Set ID:
Building 23227616
Regulation 2021 • Section 73 and 77 • Form 15 • Version 2 • March 2023 Page 3 of 5
Version: 1, Version Date: 06/09/2024
Page 4
length of the document. This is acceptable and does not change the approved form, provided the section text (description on the
left-hand side of the page) is not altered.
Document Set ID:
Building 23227616
Regulation 2021 • Section 73 and 77 • Form 15 • Version 2 • March 2023 Page 4 of 5
Version: 1, Version Date: 06/09/2024
Page 5
Appointed competent person (design-specification) – (sections 34 and 36 of the BR 2021)
A building certifier must assess and decide to appoint an individual as a competent person before they can, as a competent
person, give design-specification help. The building certifier is required to keep detailed records about what was considered
when appointing a competent person.
A building certifier must be satisfied that an individual is competent to give the type of help having regard to the individual’s
experience, qualifications and skills and if required by law to hold a licence or registration, that the individual is appropriately
registered or licensed.
An individual is appointed as competent to give design-specification help on or from a particular day.
For further information about assessment of someone as a competent person refer to the Guideline for the assessment of
competent persons.
PRIVACY NOTICE
The Department of Energy and Public Works is collecting personal information as required under the Building Act 1975. This
information may be stored by the Department, and will be used for administration, compliance, statistical research and
evaluation of building laws. Your personal information will be disclosed to other government agencies, local government
authorities and third parties for purposes relating to administering and monitoring compliance with the Building Act 1975.
Personal information will otherwise only be disclosed to third parties with your consent or unless authorised or required by law.
Document Set ID:
Building 23227616
Regulation 2021 • Section 73 and 77 • Form 15 • Version 2 • March 2023 Page 5 of 5
Version: 1, Version Date: 06/09/2024