Skip to the record
Trusted by locals. Built for Noosa.

Council archive · source document

Complied Approved Plan - Negotiated - MCU22 0145 & OPW22 0212 · MCU22/0145

of 30

Plans and drawings: the text below has words only, no drawings.

Very large file (11.2 MB): may take a few minutes to open.

Log in to see the plans as drawn

Original PDF page 20, section 1. The text section number identifies this passage in the reader.

                    NOTES:
                    1.0 GENERAL:
                    1.1    Existing surface levels are indicated thus:       15.00

                    1.2    Finished constructed levels are indicated thus:             15.000
                    1.3    All building floor levels to be confirmed and approved                                                                                                                                                                                   Saw Joint 25 deep withing
                           by the Architectural Designer prior to construction.                                                                                                                                                                                     1 day of placing concrete and
                                                                                                                                                Second Pour                  First Pour                                                                             fill with 5mm x 6mm deep
                    1.4    Contractor to obtain all necessary permits.                                                                                                                     Slab mesh as                                                             flexible sealant
                                                                                                                                                                                           specified.                                                                                                                                       Backer rod
                    1.5    Underground services are shown where known. Contractor                                      10mm x 10mm Recess filled
                                                                                                                                                                                            R20 x 600 long dowel                                                                 Remove every
                                                                                                                       with flexible sealant.
                           is to determine the exact location and depth of all                                                                                                              at 300mm crs.                                                                        second wire
                           services prior to commencing any excavation.
                                                                                                                                                                                                                             Slab thickness                         Slab as




                                                                                                             =
                    1.6    When applicable, all carparks are to be whitelined with              180 Slab
                                                                                                                                                                                                                             as specified                           detailed
                                                                                                thickening
                           100mm wide painted lines using approved linemarking




                                                                                                             =
                           paint.
                    1.7    Carry out all concrete work in accordance with AS3600.                                Grease & cap
                                                                                                                                                                                                                                                                                                       120

                    1.8    Verify all setting out dimensions prior to construction.                              this end only.                          300                 300

                    1.9    Do not obtain dimensions by scaling the structural elements.                                                                                                                                                                                          SWAN JOINT DETAILS (S.J)
                    1.10   IF DOUBT EXISTS, REFER TO ENGINEER.
                                                                                                                                       DOWEL JOINT DETAIL (D.J.)

                    2.0 DESIGN LOADS:
                     2.1 Light Vehicle Loading - 3 Tonne axle load.


                    3.0 CONCRETE:
                                                                                                                                                                                 C.I Gate/Lid (Hot dripped galv. if steel)
                    3.1    Place the following concrete (adjust target strength to                                                                                               to engineer's approval.




                                                                                                                                               ver
                                                                                                                                                                                                                                                                                                    Brushed on sika primer 1 or




                                                                                                                                            Co
                             provide F'c as defined in AS3600) :-                                                                                       Finished surface           300mm Lap




                                                                                                                                           40
                                                                                                                                                                                                                                                          Open cell polyurethane                    equivalent 1-8 hrs prior to inserting
                                                                                                                                                                                     Typical.                                                             foam backing rod                          sikaflex pro sealant or equivalent.
                               Location         F'c at 28 days as defined in AS3600
                               Driveway         25 MPa




                                                                                                                                                                                                   Varies
                                                                                                                                                                                                   Depth
                               Crossover        32 MPa
                                                                                                                      Construction Joint
                             Max. Aggregate Size: 20mm                                                                   N12 at 300mm
                             Slump: 80mm




                                                                                                                                                                                                   150
                             Cure all concrete surfaces as directed in the specification.
                                                                                                                                                                                                                                                                                     12
                    3.2    Sample and test concrete in accordance with AS3600.                                                                    150      300min.         150                                                                                                                                        R16 dowels x 400 long.
                                                                                                                                                                                         N12 longitudinals
                                                                                                                                                                                         LAP 500.                                                                                                                     Grease and cap one end.
                    3.3    Consolidate by vibration.
                                                                                                                                                 F'c = 25MPa

                                                                                                                             TRENCH GRATE CROSS SECTION                                                                                                          BOND BEAM CONTROL JOINT
                    4.0 REINFORCEMENT:                                                                                                                                                                                                                           SCALE 1:20 AT A1

                    4.1    Fix reinforcement as shown on the drawings. The type and
                           grade is indicated by a symbol as shown below. On the
                           drawings this is followed by a numeral wich indicates the
                           diameter of the bar in millimetres.
                                Hot rolled deformed bar: N
                                Structural grade plain round bar: R
                                Hard drawn wire fabric: No.
                    4.2    All laps in reinforcing steel to be full tension laps unless                                                                                                                                                                       N12 trimmer bars




                                                                                                                                                                                                                                                                                                         500 TYP.
                           noted otherwise.                                                                                                                                                                                                                   50mm side cover.
                                                                                                                                                                                                                                                              Typical.
                    4.3    Proifile bar supports or spacers to give the following
                           concrete cover to all reinforcement, unless noted
                                                                                                                      700




                           otherwise on the drawings.




                                                                                                                                                                                                                                                  700
                               Slabs: 40mm Top & Side.

                                                                                                                                       700                                                         N12 trimmer bars
                   5.0 GENERAL DRIVEWAY SLAB ON GROUND NOTES:                                                                                                  PIT                                 50mm side cover.                                           700
                                                                                                                                                                                                   Typical.                                                                      PIT
                    5.1    Subgrade Preparation:                                                                                                                                                                                                                                                                    Edge of slab
                            (a) Trim foundation material to required levels and
                                     remove any soil containing organic material.
                             (b) Proof roll to reveal any soft spots. All soft spots
                                      to be removed and replaced with a material                                         500 TYP.                                          Edge of slab                                                            300 TYP.
                                      having a minimum CBR 15 and compacted
                                      to 95% standard A.A.S.H.O.
                    5.2    Refer Architect for steps.                                                             EDGE TRIMMER DETAIL FOR SIDE DRAINAGE PIT.                                                                                  EDGE TRIMMER DETAIL FOR CORNER DRAINAGE PIT.
                    5.3    Pour slab on waterproof membrane to Architect's
                           details on 50mm of bedding sand.
                    5.4    Filling as required to bring the site to grade shall be
                           CBR 15 material compacted to 95% standard A.A.S.H.O.
                           in layers of 150mm maximum. The builder shall take
                           compaction tests to verify the degree of compaction
                           and provide the certificates to the Engineer.
                    5.5    Certification of the quality of the CBR 15 material shall
                           be provided to the Engineer for approval prior to
                           delivery to the site.
                    5.6    Construction joints shall be located at sawn or dowel
                           joints. If located at sawn joint substitute dowel joint
                           detail.


                            REAL PROPERTY BOUNDARIES ARE TO BE ESTABLISHED BY
                            A LICENCED SURVEYOR. THE CONTRACTOR SHALL CONFIRM
                            TO THE SUPERVISING ENGINEER THAT THIS HAS BEEN
                            COMPLETED TO SUCH A STANDARD THAT WILL PERMIT
                            WORKS TO BE SET OUT ACCURATELY. THE ENGINEER SHALL
                            BE GIVEN THE OPPORTUNITY TO CONFIRM SUCH SETOUT
                            BEFORE CONSTRUCTION COMMENCES.




                        NOOSA COUNCIL                                                                                                                                                                                                                                                                                                                               Issue   Made By   Date       Description
                                                                                                                                                                                                                                                                                                                                                                                                                                  PROPOSED RESIDENCE                                                                                                                                                    Scale : AS SHOWN   NOTES:
                        APPROVED PLAN                                                                                                                                                                                                                                                                                                                                 F     M.T.      20/02/23   For Operational Works Approval
                                                                                                                                                                                                                                                                                                                                                         REVISION




                                                                                                                                                                                                                                                                                                                                                                                                                                  at No.3 HENDERSON STREET SUNSHINE BEACH                                                                                                                               Job No.: 22-0360   1. Do not scale drawings.
                     MCU22/0145 & OPW22/0212                                                                                                                                                                                                                                                                                                                          G     M.T.      22/06/23   For Operational Works Approval
                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                           2. Scale is correct at A3.
                                                                                                                                                                                                                                                                                                                                                                                                                                  Client: JMML DEVELOPMENTS
                           22 DEC 2023                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                  Dwg No.: C01       3. Check and verify all dimensions
                                                                                                                                                                                                                                                                                                                                                                                                                                  Designed By : B.J. WINNING BEngTech (Civil), MEngPrac (Civil), MIEAust Drawn By : MT   Date : 20/05/22                                                                                     prior to commencement of work.
                                                                                                                                                                                                                                                                                                                                                                                                                                  Certified By : B.R. CROMAR BEng(Civil), MEIAust, CPEng, RPEQ, NER                      Date : 20/05/22   Ph: (07) 5444 5578   Email: [email protected]   GENERAL NOTES

Document Set ID: 22490617
Version: 1, Version Date: 05/07/2023

Used in these records

About this file

File size
11.2 MB (very large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

Complied Approved Plan - Negotiated - MCU22 0145 & OPW22 0212.pdf · 11.2 MB (very large file)

The download may take a few minutes. On mobile data, it is best to wait for Wi-Fi.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.