Original source · versioned page text
BR2C3.LST
From the archive CALPUFF.zip (folder CALPUFF/AMG_NewPlan/BIOR2/BR2C3), inside D21030-2_NoosaSprings_Files ODOUR MODELLING - Part RFI.zip. File date in the archive: 2018-08-20 21:42.
!
Default plume path coefficients for
each stability class (used when option
for partial plume height terrain adjustment
is selected -- MCTADJ=3)
(PPC(6)) Stability Class : A B C D E F
Default PPC : .50, .50, .50, .50, .35, .35
--- --- --- --- --- ---
! PPC = 0.50, 0.50, 0.50, 0.50, 0.35, 0.35 !
Slug-to-puff transition criterion factor
equal to sigma-y/length of slug
(SL2PF) Default: 10. ! SL2PF = 10.0 !
Receptor-specific puff/slug properties (e.g., sigmas and height above
ground at the time when the trajectory is nearest the receptor) may be
extrapolated forward or backward in time along the current step using
the current dispersion, for receptors that lie upwind of the puff/slug
position at the start of a step, or downwind at the end of a step.
Specify the upwind/downwind extrapolation zone in sigma-y units.
Using FCLIP=1.0 clips the the upwind zone at one sigma-y at the start
of the step and the downwind zone at one sigma-y at the end of the step.
This is consistent with the sampling done in CALPUFF versions through
v6.42 prior to the introduction of the FCLIP option.
The default is No Extrapolation, FCLIP=0.0.
(FCLIP) Default: 0.0 ! FCLIP = 0.0 !
Puff-splitting control variables ------------------------
VERTICAL SPLIT
--------------
Number of puffs that result every time a puff
is split - nsplit=2 means that 1 puff splits
into 2
(NSPLIT) Default: 3 ! NSPLIT = 3 !
Time(s) of a day when split puffs are eligible to
be split once again; this is typically set once
per day, around sunset before nocturnal shear develops.
24 values: 0 is midnight (00:00) and 23 is 11 PM (23:00)
0=do not re-split 1=eligible for re-split
(IRESPLIT(24)) Default: Hour 17 = 1
! IRESPLIT = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,0,0,0,0,0,0 !
Split is allowed only if last hour's mixing
height (m) exceeds a minimum value
(ZISPLIT) Default: 100. ! ZISPLIT = 100.0 !
Split is allowed only if ratio of last hour's
mixing ht to the maximum mixing ht experienced
by the puff is less than a maximum value (this
postpones a split until a nocturnal layer develops)
(ROLDMAX) Default: 0.25 ! ROLDMAX = 0.25 !
HORIZONTAL SPLIT
----------------
Number of puffs that result every time a puff
is split - nsplith=5 means that 1 puff splits
into 5
(NSPLITH) Default: 5 ! NSPLITH = 5 !
Minimum sigma-y (Grid Cells Units) of puff
before it may be split
(SYSPLITH) Default: 1.0 ! SYSPLITH = 1.0 !
Minimum puff elongation rate (SYSPLITH/hr) due to
wind shear, before it may be split
(SHSPLITH) Default: 2. ! SHSPLITH = 2.0 !
Minimum concentration (g/m^3) of each
species in puff before it may be split
Enter array of NSPEC values; if a single value is
entered, it will be used for ALL species
(CNSPLITH) Default: 1.0E-07 ! CNSPLITH = 1.0E-07 !
Integration control variables ------------------------
Fractional convergence criterion for numerical SLUG
sampling integration
(EPSSLUG) Default: 1.0e-04 ! EPSSLUG = 1.0E-04 !
Fractional convergence criterion for numerical AREA
source integration
(EPSAREA) Default: 1.0e-06 ! EPSAREA = 1.0E-06 !
Trajectory step-length (m) used for numerical rise
integration
(DSRISE) Default: 1.0 ! DSRISE = 1.0 !
Boundary Condition (BC) Puff control variables ------------------------
Minimum height (m) to which BC puffs are mixed as they are emitted
(MBCON=2 ONLY). Actual height is reset to the current mixing height
at the release point if greater than this minimum.
(HTMINBC) Default: 500. ! HTMINBC = 500.0 !
Search radius (km) about a receptor for sampling nearest BC puff.
BC puffs are typically emitted with a spacing of one grid cell
length, so the search radius should be greater than DGRIDKM.
(RSAMPBC) Default: 10. ! RSAMPBC = 10.0 !
Near-Surface depletion adjustment to concentration profile used when
sampling BC puffs?
(MDEPBC) Default: 1 ! MDEPBC = 1 !
0 = Concentration is NOT adjusted for depletion
1 = Adjust Concentration for depletion
!END!
-------------------------------------------------------------------------------
INPUT GROUPS: 13a, 13b, 13c, 13d -- Point source parameters
--------------------------------
---------------
Subgroup (13a)
---------------
Number of point sources with
parameters provided below (NPT1) No default ! NPT1 = 0 !
Units used for point source
emissions below (IPTU) Default: 1 ! IPTU = 1 !
1 = g/s
2 = kg/hr
3 = lb/hr
4 = tons/yr
5 = Odour Unit * m**3/s (vol. flux of odour compound)
6 = Odour Unit * m**3/min
7 = metric tons/yr
8 = Bq/s (Bq = becquerel = disintegrations/s)
9 = GBq/yr
Number of source-species
combinations with variable
emissions scaling factors
provided below in (13d) (NSPT1) Default: 0 ! NSPT1 = 0 !
Number of point sources with
variable emission parameters
provided in external file (NPT2) No default ! NPT2 = 0 !
(If NPT2 > 0, these point
source emissions are read from
the file: PTEMARB.DAT)
!END!
---------------
Subgroup (13b)
---------------
a
POINT SOURCE: CONSTANT DATA
-----------------------------
b c
Source X Y Stack Base Stack Exit Exit Bldg. Emission
No. Coordinate Coordinate Height Elevation Diameter Vel. Temp. Dwash Rates
(km) (km) (m) (m) (m) (m/s) (deg. K)
------ ---------- ---------- ------ ------ -------- ----- -------- ----- --------
--------
a
Data for each source are treated as a separate input subgroup
and therefore must end with an input group terminator.
SRCNAM is a 12-character name for a source
(No default)
X is an array holding the source data listed by the column headings
(No default)
SIGYZI is an array holding the initial sigma-y and sigma-z (m)
(Default: 0.,0.)
FMFAC is a vertical momentum flux factor (0. or 1.0) used to represent
the effect of rain-caps or other physical configurations that
reduce momentum rise associated with the actual exit velocity.
(Default: 1.0 -- full momentum used)
ZPLTFM is the platform height (m) for sources influenced by an isolated
structure that has a significant open area between the surface
and the bulk of the structure, such as an offshore oil platform.
The Base Elevation is that of the surface (ground or ocean),
and the Stack Height is the release height above the Base (not
above the platform). Building heights entered in Subgroup 13c
must be those of the buildings on the platform, measured from
the platform deck. ZPLTFM is used only with MBDW=1 (ISC
downwash method) for sources with building downwash.
(Default: 0.0)
b
0. = No building downwash modeled
1. = Downwash modeled for buildings resting on the surface
2. = Downwash modeled for buildings raised above the surface (ZPLTFM > 0.)
NOTE: must be entered as a REAL number (i.e., with decimal point)
c
An emission rate must be entered for every pollutant modeled.
Enter emission rate of zero for secondary pollutants that are
modeled, but not emitted. Units are specified by IPTU
(e.g. 1 for g/s).
---------------
Subgroup (13c)
---------------
BUILDING DIMENSION DATA FOR SOURCES SUBJECT TO DOWNWASH
-------------------------------------------------------
Source a
No. Effective building height, width, length and X/Y offset (in meters)
every 10 degrees. LENGTH, XBADJ, and YBADJ are only needed for
MBDW=2 (PRIME downwash option)
------ --------------------------------------------------------------------
--------
a
Building height, width, length, and X/Y offset from the source are treated
as a separate input subgroup for each source and therefore must end with
an input group terminator. The X/Y offset is the position, relative to the
stack, of the center of the upwind face of the projected building, with the
x-axis pointing along the flow direction.
---------------
Subgroup (13d)
---------------
a
POINT SOURCE: EMISSION-RATE SCALING FACTORS
-------------------------------------------
Use this subgroup to identify temporal variations in the emission
rates given in 13b. Factors assigned multiply the rates in 13b.
Skip sources here that have constant emissions. For more elaborate
variation in source parameters, use PTEMARB.DAT and NPT2 > 0.
Sets of emission-rate scale factors are defined in Input Group 19, and
are referenced by the FACTORNAME. Provide NSPT1 lines that identify the
emission-rate scale factor table for each source-species combination that
uses the scaling option. Note that a scale-factor table can be used with
more than one source-species combination so a FACTORNAME can be repeated.
Source- Source Species Scale-factor table
Species Name b Name c Name d
No. (SRCNAM) (CSPEC) (FACTORNAME)
------ ------------ ------------ ---------------------
--------
a
Assignment for each source-specie is treated as a separate input subgroup
and therefore must end with an input group terminator.
b
Source name must match one of the SRCNAM names defined in Input Group 13b
c
Species name must match one of the CSPEC names of emitted species defined in Input Group 3
d
Scale-factor name must match one of the FACTORNAME names defined in Input Group 19
-------------------------------------------------------------------------------
INPUT GROUPS: 14a, 14b, 14c, 14d -- Area source parameters
--------------------------------
---------------
Subgroup (14a)
---------------
Number of polygon area sources with
parameters specified below (NAR1) No default ! NAR1 = 1 !
Units used for area source
emissions below (IARU) Default: 1 ! IARU = 1 !
1 = g/m**2/s
2 = kg/m**2/hr
3 = lb/m**2/hr
4 = tons/m**2/yr
5 = Odour Unit * m/s (vol. flux/m**2 of odour compound)
6 = Odour Unit * m/min
7 = metric tons/m**2/yr
8 = Bq/m**2/s (Bq = becquerel = disintegrations/s)
9 = GBq/m**2/yr
Number of source-species
combinations with variable
emissions scaling factors
provided below in (14d) (NSAR1) Default: 0 ! NSAR1 = 0 !
Number of buoyant polygon area sources
with variable location and emission
parameters (NAR2) No default ! NAR2 = 0 !
(If NAR2 > 0, ALL parameter data for
these sources are read from the file: BAEMARB.DAT)
!END!
---------------
Subgroup (14b)
---------------
a
AREA SOURCE: CONSTANT DATA
----------------------------
b
Source Effect. Base Initial Emission
No. Height Elevation Sigma z Rates
(m) (m) (m)
------- ------ ------ -------- ---------
1! SRCNAM = BR2C3 !
1! X = 1.0, 22.9, 1.0, 2.62 ! !END!
--------
a
Data for each source are treated as a separate input subgroup
and therefore must end with an input group terminator.
b
An emission rate must be entered for every pollutant modeled.
Enter emission rate of zero for secondary pollutants that are
modeled, but not emitted. Units are specified by IARU
(e.g. 1 for g/m**2/s).
---------------
Subgroup (14c)
---------------
COORDINATES (km) FOR EACH VERTEX(4) OF EACH POLYGON
--------------------------------------------------------
Source a
No. Ordered list of X followed by list of Y, grouped by source
------ ------------------------------------------------------------
1! SRCNAM = BR2C3 !
1! XVERT = 508.748, 508.748, 508.754, 508.754 !
1! YVERT = 7078.452, 7078.458, 7078.458, 7078.453 ! !END!
--------
a
Data for each source are treated as a separate input subgroup
and therefore must end with an input group terminator.
---------------
Subgroup (14d)
---------------
a
AREA SOURCE: EMISSION-RATE SCALING FACTORS
-------------------------------------------
Use this subgroup to identify temporal variations in the emission
rates given in 14b. Factors assigned multiply the rates in 14b.
Skip sources here that have constant emissions. For more elaborate
variation in source parameters, use BAEMARB.DAT and NAR2 > 0.
Sets of emission-rate scale factors are defined in Input Group 19, and
are referenced by the FACTORNAME. Provide NSAR1 lines that identify the
emission-rate scale factor table for each source-species combination that
uses the scaling option. Note that a scale-factor table can be used with
more than one source-species combination so a FACTORNAME can be repeated.
Source- Source Species Scale-factor table
Species Name b Name c Name d
No. (SRCNAM) (CSPEC) (FACTORNAME)
------ ------------ ------------ ---------------------
--------
a
Assignment for each source-specie is treated as a separate input subgroup
and therefore must end with an input group terminator.
b
Source name must match one of the SRCNAM names defined in Input Group 14b
c
Species name must match one of the CSPEC names of emitted species defined in Input Group 3
d
Scale-factor name must match one of the FACTORNAME names defined in Input Group 19
-------------------------------------------------------------------------------
INPUT GROUPS: 15a, 15b, 15c -- Line source parameters
---------------------------
---------------
Subgroup (15a)
---------------
Number of buoyant line sources
with variable location and emission
parameters (NLN2) No default ! NLN2 = 0 !
(If NLN2 > 0, ALL parameter data for
these sources are read from the file: LNEMARB.DAT)
Number of buoyant line sources (NLINES) No default ! NLINES = 0 !
Units used for line source
emissions below (ILNU) Default: 1 ! ILNU = 1 !
1 = g/s
2 = kg/hr
3 = lb/hr
4 = tons/yr
5 = Odour Unit * m**3/s (vol. flux of odour compound)
6 = Odour Unit * m**3/min
7 = metric tons/yr
8 = Bq/s (Bq = becquerel = disintegrations/s)
9 = GBq/yr
Number of source-species
combinations with variable
emissions scaling factors
provided below in (15c) (NSLN1) Default: 0 ! NSLN1 = 0 !
Maximum number of segments used to model
each line (MXNSEG) Default: 7 ! MXNSEG = 7 !
The following variables are required only if NLINES > 0. They are
used in the buoyant line source plume rise calculations.
Number of distances at which Default: 6 ! NLRISE = 6 !
transitional rise is computed
Average building length (XL) No default ! XL = .0 !
(in meters)
Average building height (HBL) No default ! HBL = .0 !
(in meters)
Average building width (WBL) No default ! WBL = .0 !
(in meters)
Average line source width (WML) No default ! WML = .0 !
(in meters)
Average separation between buildings (DXL) No default ! DXL = .0 !
(in meters)
Average buoyancy parameter (FPRIMEL) No default ! FPRIMEL = .0 !
(in m**4/s**3)
!END!
---------------
Subgroup (15b)
---------------
BUOYANT LINE SOURCE: CONSTANT DATA
----------------------------------
a
Source Beg. X Beg. Y End. X End. Y Release Base Emission
No. Coordinate Coordinate Coordinate Coordinate Height Elevation Rates
(km) (km) (km) (km) (m) (m)
------ ---------- ---------- --------- ---------- ------- --------- ---------
--------
a
Data for each source are treated as a separate input subgroup
and therefore must end with an input group terminator.
b
An emission rate must be entered for every pollutant modeled.
Enter emission rate of zero for secondary pollutants that are
modeled, but not emitted. Units are specified by ILNTU
(e.g. 1 for g/s).
---------------
Subgroup (15c)
---------------
a
BUOYANT LINE SOURCE: EMISSION-RATE SCALING FACTORS
--------------------------------------------------
Use this subgroup to identify temporal variations in the emission
rates given in 15b. Factors assigned multiply the rates in 15b.
Skip sources here that have constant emissions. For more elaborate
variation in source parameters, use LNEMARB.DAT and NLN2 > See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the original