Council archive · source document
Response to Information Request · OPW11/0281
NOTES.
1. THESE DRAWINGS SHALL BE READ IN CONJUNCTION WITH ALL OTHER CONSULTANTS
DRAWINGS AND SPECIFICATIONS.
S
2. BEFORE PROCEEDING WITH THE WORK ANY DISCREPANCIES IN THE CONTRACT
DOCUMENTS SHALL BE REFERRED FOR DECISION TO THE ENGINEER.
3. 00 NOT SCALE FROM DRAWINGS IF IN DOUBT. ASKS t
4. CONTRACTOR SHALL VERIFY ALL LOCATIONS OF SERVICES. ALL DIMENSIONS AND
LEVELS PRIOR TO CONSTRUCTION.
5. ALL MATERIALS & WORKMANSHIP SHALL BE IN ACCORDANCE WITH AS2890, THE
BUILDING CODE OF AUSTRALIA (INCLUDING THE QUEENSLAND SUPPLEMENT(. THE
QUEENSLAND BUILDING ACT AMENDMENT ACT 1991 AND THE LOCAL AUTHORITY'S
BY-LAWS.
S. THE CONTRACTOR IS RESPONSIBLE TO OBTAIN RELEVANT APPROVALS PRIOR TO
COMMENCEMENT OF WORKS.
6. ALL STORMWATER CULVERTS TO BE RCP CLASS 2. ALL ROOFWATER PIPES TO BE
uPVC CLASS '5H'.
7. SILT MANAGEMENT PLAN TO REMAIN IN PLACE UNTIL COMPLETION OF WORKS AND
SATISFACTORY MAINTENANCE IS COMPLETED.
8. ALL PROPOSED OPERATIONAL WORKS SHALL BE CONSTRUCTED IN ACCORDANCE
WITH COUNCIL'S OPERATIONAL WORKS APPROVAL LETTER AND COUNCIL'S DECISION
NOTICE-DEVELOPMENT PERMIT.
9. CONCRETE KERB RAMPS SHALL BE ALIGNED TO COMPLY WITH COUNCIL'S STANDARD m
DRAWING AND SHALL BE CONSTRUCTED STRICTLY IN ACCORDANCE WITH
oar
I-
COUNCIL STANDARD DRAWING. J 0
10. ALL TEMPORARY & PERMANENT ROAD SIGNS AND LINEMARKING SHALL COMPLY WITH N
0
THE CURRENT MANUAL OF UNIFORM TRAFFIC CONTROL DEVICESIM.U.T.C.0.1. EXISTING LINE Z
MARKING SHALL BE REMOVED BY GRINDING NOT"BLACKING OUT. COUNCIL DOES NOT
APPROVE OF BLACKING OUT OF EXISTING LINE MARKING.
SEWERAGE NOTES
1. Where ductile iron pipe is specified it -,a
shall be class K9 heavy cement lined.
2. Where sewers are laid in fill, such fill
shall be compacted 95% standard A.A.S.H.O.
in maximum layers of 150mm. Proof of
compaction is to be submitted to the
superintendant.
3. House connection branches to be installed
in accordance with COUNCIL Standard Drawings.
4. Work on existing sewers to be carried out
by COUNCIL at developers cost. NOTES:
5. Drops to be external in D.I.C.L. or PVC. 1. Crossings are not designed for commercial vehicles.
2. Footpath section to vary where necessary to match concrete footpaths and
6. Sewers to be laid in accordance with COUNCIL verge profiles. Footpath earthworks adjoining concrete must be well compacted
Guidelines, bedding type A unless 3. Concrete surface tolerances to be +Smm/-Omm over 3 metre section
otherwise instructed. 4. Concrete N25 in accordance with AS 1379, and AS 3600
7. Min. clear cover to be as per Table 4.8 5. Reinforced fabric to AS 1304,50 lop and edge cover, lop fabric 250mm
of WSA02. 6. Approved materials for construction:- Concrete, paving blocks or asphalt
7. Expansion joints to be 10mm wide, full depth closed cell cross linked a
0
8. Sewers constructed at grades greater than polyethylene foam (85 - 150 kg/m sq) or compressed granulated corkboard,
1 in 6 shall be provided with concrete stops installation to manufacturers' specifications.
in accordance with Council's guidelines 8. All appropriate permits must be obtained from council, including approval
of location and levels prior to excavation.
9. Preferred sewer alignment is 1.5m from front
and rear boundaries, and 1m from side boundary. 9. Refer protect drawings of local authourity standard drawings for verge
type cross sections.
10. Manhole covers shall be 600mm clear opening ductile 10. One access point to be constructed to each lot as per standard drawing.
iron covers and cast iron frames and be 75mm above It. Earthworks cut and lit batters from edge of driveway to natural surface
finished surface level as per WSA02 Std Dwg No. SEW-1308. to be max. grade at 1 in 10 and fully turfed.
12. Driveways must ocheive a high point of 250mm obove invert of kerb to ensure
11. House connections in adjoining properties to the sewer stormwater is contained within rood reserve as per requirement of QUDM. V
line shall extend 1.5m into the property being served. BARRIER, SEMI - MOUNTABLE OR Cr
This constraint may be varied upon the approval of local authority. 0
13. Existing footpath to be transitional to new driveway at a max grade of 1 in 10. MOUNTABLE KERB & CHANNEL BREAKOUT
12. All house connections joining to sewers deeper than
14. Under special circumstances Council may approve a rising grade of 1 in 8 in
2.1m are to use sugden fittings.
13. Installation of detectable marker tape for all non-metallic sewer
this location or Within Im of the property boundary,
15. All dimensions are in millimetres, unless noted otherwise.
CROSSOVER DETAIL
mains is required in accordance with Council's requirements.
N
r Kam H 1 i
Pavement Level Location
Bolster cut slob (3w x 30d)
Fill joint to 3mm. below surface
with Fosroc Expandite Thioflex 600g
or similar,
NOTE
Cut every second wire
SAW (VT5 FUSING A SOFT (UT SAW( SHALL
BE INSTALLED WITHIN B HOURS OF CONCRETE directly under joint and
FOR NFOMA1aN NOT SHOWN REFER NFJwe COAST RECO)W SNAE OOUra,
RLACENENT IWMEN AVERAGE AMBIENT depress fabric locally. Shin S,*N Ds»oo
rEMVERAIVRE EXCEEDS 32- ENS Iww Eviq, & Smxy Smrus Wit 0-wig Mxr&w 40 R-0050 MARCH 2008
SHALL BE REDUCED TO 4 HOUR 1.
SAW CUT - (SCI TYPICAL PROFILE DRIVEWAY ACCESS
See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalUsed in these records
Response to Information RequestRelated documentApplication case desk ↗
About this file
- File size
- 1.9 MB (small file)
- File type
No other editions are linked here.