Skip to the record
Trusted by locals. Built for Noosa.

Council archive · source document

Attachment G_Geotechnical_Report · MCU23/0070

of 38

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

Report on Geotechnical Investigation
Proposed Mixed-Use Development
36-38 Duke Street, Sunshine Beach




Prepared for:
Faris Cosic
Cambooya Pty Ltd
Level 14, 131 Macquarie Street
Sydney NSW 2000
Report Number: J001873-001-R-Rev1
August 2023
Full text of the other 37 pages

Page 2

Cambooya Pty Ltd


Table of Contents

1.0       INTRODUCTION .................................................................................................................................... 1
2.0       PROPOSED DEVELOPMENT ............................................................................................................... 1
3.0       SITE DESCRIPTION .............................................................................................................................. 1
4.0       METHODOLOGY ................................................................................................................................... 3
4.1       Fieldwork................................................................................................................................................. 3
5.0       INVESTIGATION FINDINGS .................................................................................................................. 4
5.1       Geology & Landslide Hazard Mapping ................................................................................................... 4
5.2       Ground Conditions .................................................................................................................................. 4
6.0       GEOTECHNICAL RECOMMENDATIONS ............................................................................................. 5
6.1       Earthworks .............................................................................................................................................. 5
6.1.1         Site Preparation & Filling .................................................................................................................... 5
6.1.2         Temporary Batter slopes .................................................................................................................... 6
6.1.3         Excavatability ...................................................................................................................................... 6
6.2       Foundations ............................................................................................................................................ 6
6.2.1         Footing Design .................................................................................................................................... 6
6.2.2         Site Classification ............................................................................................................................... 7
6.3       Retaining Wall Design ............................................................................................................................ 7
6.4       Drainage & Erosion Control .................................................................................................................... 8
7.0       STABILITY RISK ASSESSMENT ........................................................................................................... 8
7.1       General Foundation Maintenance .......................................................................................................... 9
8.0       LIMITATIONS ......................................................................................................................................... 9


Tables
Table 1: Lateral Earth Pressure Coefficients. .................................................................................................... 7
Table 2: Stability Risk Levels. ............................................................................................................................ 8
Table 3: Qualitative Risk Assessment for Property (Based on AGS 2007)....................................................... 8



Appendices
Appendix A Site Plan
Appendix B Reports of Boreholes and Explanatory Notes
Appendix C Qualitative Terminology for Use in Assessing Risk to Property (AGS 2007)
Appendix D A Guide to Preventing Structural Damage V3 (QBCC 2015)
Appendix E Limitations




J001873-001-R-Rev1                                                                                                                                  Page ii

Page 3

Cambooya Pty Ltd


1.0     INTRODUCTION
As requested by JFP Urban Consultants Pty Ltd, on behalf of Cambooya Pty Ltd, Core Consultants Pty Ltd
(Core) has carried out a geotechnical investigation and slope stability assessment for a proposed mixed-use
development at 36-38 Duke Road, Sunshine Beach.

2.0     PROPOSED DEVELOPMENT
We understand that the proposed development is to comprise a three to four-storey building that is to be
terraced up the sloping ground surface, as shown on Image 1. The lower level on the southern two thirds of
the site is anticipated to require excavations of up to about 3 m depth and retention of the upslope ground.
The construction of the development will require the demolition of the existing structure and will need to be
constructed so as to not impact the adjacent structures. The existing building to the east is believed to have
a basement level at or close to the basement level of the proposed building on the subject site.
Design drawings and foundation loads have not been provided at the time of writing; however, it is
anticipated from similar type developments that foundation working loads for a four-level building will be in
the order of about 1,500 kN to 2,500 kN under columns (depending on the column/wall spacing
configuration).




Image 1: Section view of proposed development (refer Blackburne Jackson Dwg. No. 7252-DA15)


3.0     SITE DESCRIPTION
The site has frontage to Duke Street along the southern end of the property boundary, with Douglas Lane
along the northern property boundary. Mixed-use retail and residential buildings are situated to the east and
west.
The existing building is positioned on the southern half of the site. The topography on the northern half of the
site generally comprises two breaks in slope, with measured slope angles of between 3° and 19° towards the
south-east. A small retaining wall is located just to the north of the existing building.
Photographs 1 to 3 show the general site conditions at the time of our investigation. Figure 1 in Appendix A
displays the site layout.




J001873-001-R-Rev1                                                                                  Page 1

Page 4

Cambooya Pty Ltd




Photograph 1: Looking approximately south-east along the eastern site boundary, from Douglas Lane.




Photograph 2: Looking approximately south over the centre of the site.


J001873-001-R-Rev1                                                                              Page 2

Page 5

Cambooya Pty Ltd




                                                             BH2


Photograph 3: Looking approximately north over the centre of the site from the western corer of the existing
building.

4.0     METHODOLOGY
Our investigation and assessment included the following:

     A review of geological and landslide hazard overlay plans.

      Subsurface investigation at two borehole locations.

     A slope stability risk assessment in accordance with the Australian Geomechanics Society (AGS)
      Guidelines for Landslide Risk Management (March 2007).


4.1   Fieldwork
Fieldwork was carried out on 9 February 2023. The subsurface investigation comprised two boreholes
(designated BH1 and BH2). Borehole BH1 was drilled with a 4WD-mounted auger rig to 6 m below ground
level (BGL), and borehole BH2 was hand-augered to 1.6 m BGL.

Dynamic cone penetrometer (DCP) testing was undertaken adjacent to/within the boreholes to assess soil
consistency/density.
The borehole locations are shown on Figure 1 in Appendix A, and Reports of Boreholes are presented in
Appendix B, together with explanatory notes. The ground conditions are discussed in Section 5.2.
The fieldwork was carried out by a geotechnical engineer from Core who logged subsurface conditions in
accordance with AS1726-2017 Geotechnical site investigations.




J001873-001-R-Rev1                                                                                  Page 3

Page 6

Cambooya Pty Ltd

5.0            INVESTIGATION FINDINGS

5.1         Geology & Landslide Hazard Mapping
The Gympie Special Geology map 1 indicates that the site is underlain by Quaternary aged dune quartz sand,
as shown on the extract in Image 2.




                                                             Approximate site location




Image 2: Site geology from the Gympie Special Geology Map.
The Noosa Council Landslide Hazard overlay mapping, refer Image 3, indicates that the site is within an area
of moderate to high landslide hazard (susceptibility).




                                                                                               Location of subject site




Image 3: Extract from Noosa Council Landslide Hazard Overlay Map.


5.2         Ground Conditions
The natural subsurface conditions encountered in the boreholes generally comprised:

           Topsoil between 0.2 m and 0.4 m thick, overlying



1
    GYMPIE SPECIAL 100K 1:100,000 Geological Series. Map Sheet 9445 and Part 9545, First Edition, Department of Mines and Energy, Brisbane, 1999.




J001873-001-R-Rev1                                                                                                                                  Page 4

Page 7

Cambooya Pty Ltd


     Loose grading to very dense dune sand (aeolian) with layers of weakly cemented indurated sand (i.e.,
      ‘coffee rock’; refer below for description of coffee rock formation).
Groundwater was not encountered in any of the boreholes.

 Coffee rock on the Sunshine Coast: what, where and why?
 Coffee rock is the colloquial term for cemented (indurated) sand, that often has the physical characteristics of
 weathered rock.

 It comprises ancient alluvial / aeolian sands of the Pleistocene age (2 million to 10,000 years ago). Coffee
 rock is typically dark brown in colour, and when disturbed breaks up into dark brown silty sand (hence the
 colloquial name ‘coffee rock’).
 Cementation in these sands is thought to have occurred as a result of the interaction of organic matter and
 mineral-rich sand, e.g., flocculation at the interface of a fluctuating groundwater level.
 Coffee rock can be weakly or strongly cemented and is often discontinuous and of variable strength and
 thickness. It is generally of low permeability, and often associated with high ‘perched’ groundwater.
 On the Sunshine Coast, coffee rock is common at many locations along the coastline, generally buried under
 younger alluvial soils (e.g., dune or beach sand). Coffee rock is often exposed and re-buried in the intertidal
 zone by cycles of natural sand movement.
 Previous investigations have found the coffee rock to be underlain by dense, non-cemented sand in most
 areas, or soft alluvial clay in some instances.
 Coffee rock presents geotechnical constraints and opportunities to infrastructure development and
 maintenance, e.g., excavatability, groundwater management, and foundations. It is considered a key element
 in the stability of the region’s coastline, likely providing protection from erosion and storm events.


6.0     GEOTECHNICAL RECOMMENDATIONS

6.1   Earthworks

6.1.1 Site Preparation & Filling
Prior to construction at-grade, the following works are recommended:

     Strip the surface of existing vegetation and root affected soils and loose disturbed material likely to be
      present following the demolition of the existing building. Localised deeper stripping/excavation may
      also be required where larger tree root systems need to be removed and/or beneath the existing
      building if any debris or remnant building items remain. Any organic rich topsoil must not be used as
      fill in proposed building areas, however it may be used for non-structural purposes (i.e., landscaping).

     ‘Proof roll’ the stripped surface by several passes of a minimum 10 tonne smooth drum roller to
      identify loose areas.

     A suitably qualified and experienced geotechnical engineer should carry out inspections of the
      subgrade to help identify any areas of unsuitable material or weak subgrade that may be present
      following stripping. Loose and/or over dry sand will require moisture adjustment and compaction.

     Loose areas identified by proof rolling should be treated by over excavation and re-compaction of the
      natural aeolian sand (providing these are free from organic matter).
Contractors carrying out compaction of existing subgrade will need to be aware of potential damage to
adjacent buildings due to vibration effects. Compaction may need to be carried out without vibrations. We
also recommend undertaking a condition assessment (dilapidation survey) of adjacent and neighbouring
structures prior to commencement of earthworks. It would also be prudent to confirm the foundation systems
of the adjacent properties, to ensure that these foundations are not undermined during any excavation
works.



J001873-001-R-Rev1                                                                                              Page 5

Page 8

Cambooya Pty Ltd

Re-compaction of materials should be undertaken under ‘Level 1’ inspection and testing as detailed in
Australian Standard AS3798-2007 Guidelines on Earthworks for Residential and Commercial Developments.
Working platform assessments must be undertaken by a suitably qualified person (i.e., RPEQ geotechnical
engineer) for large plant (e.g., cranes).


6.1.2 Temporary Batter slopes
Temporary unsurcharged batters in loose to very dense sand up to 3 m vertical height should not be formed
steeper than 1V:3H. Flatter batters may be required if localised instability or groundwater is encountered
during construction.


6.1.3 Excavatability
Cut excavations of up to about 3 m high are anticipated. Excavations within this depth range should be
achievable with small to medium earthmoving equipment (i.e., 8 to 12 tonne excavators). Larger machinery
will however improve production rates. Depending on the strength of cementation of the exposed indurated
sand (i.e., coffee rock), ripping attachments may be required.


6.2     Foundations

6.2.1      Footing Design
Conventional high-level strip and pad footings could be considered to support the proposed building,
however, where footings are located along the east and west boundaries adjacent to existing structures,
footings will need to be founded below the zone of influence of these structures. It is recommended that
additional investigation be undertaken prior to construction, to assess foundation depths of the adjacent
structures. It is likely that foundations along the east and west boundaries will require the use of a contiguous
piled system (refer Section 6.3).
Where high-level strip or pad footings are able to be adopted, these should be founded at least 0.4 m into
the underlying very dense sand, designed using an allowable bearing pressure of 400 kPa.
Footing settlements would not be expected to exceed around 1 % of footing width for pads and strips, under
serviceability loads.
Piles could comprise bored piers or continuous flight auger (CFA) piles. Liners may be required for bored
piles to prevent the upper loose to medium dense sands from caving in. The use of driven piles (including
sheet piles) is not considered suitable due to vibrational impacts on the surrounding structures.
Bored or CFA piles founded in the underlying very dense sand could be designed using an ultimate bearing
pressure of 1.5 MPa, and ultimate skin friction of 70 kPa.
A geotechnical engineer must confirm the design bearing pressures during construction. Footing excavations
must be dry and cleaned of any loose, disturbed, or saturated materials prior to pouring concrete.
If any soil conditions encountered during the footing excavations are found to differ from those noted in the
geotechnical investigation, Core should be notified immediately, and an assessment of the footing
excavations should be carried out to assess if changes to footing design are required.
All footings should found such that they are not adversely affected by any adjacent excavations, batter
slopes, trenches, or retaining walls that are not designed to support building or fill loads.
To minimise the potential for any adverse interaction effects, footings should found at least below a plane
extending 1 m horizontally from the base of trenches/batter slopes/excavations/retaining walls, then rising up
at 1V:1H. This requirement is illustrated in the following diagram.




J001873-001-R-Rev1                                                                                   Page 6

Page 9

Cambooya Pty Ltd




6.2.2       Site Classification
The site classification derived in accordance with Australian Standard AS 2870-2011 Residential slabs and
footings is not directly applicable to developments of this type but can provide an indication of the likely
magnitude of reactive (shrink and swell) movements associated with normal seasonal soil moisture
variations; and be used for plumbing design.
The site, in its state at the time of our investigation, would be classified as ‘Class ‘S’ in accordance with AS
2870-2011. The estimated characteristic ground surface movement due to seasonal moisture variation (‘ys’
value) is less than 20 mm.
It should be noted that the predicted order of movement is based on the existing soil profile (i.e., no cutting or
filling), and moisture content changes within soils due to normal seasonal moisture variations only (i.e., does
not consider soil settlement).


6.3     Retaining Wall Design
It is anticipated that the use of a contiguous piled system will be required to support cut excavations, and to
transfer proposed structure loads beneath the zone of influence of footings of the adjacent structures (on the
eastern and western site boundaries).
The design of flexible retaining walls (either fully cantilevered, or single propped) may be undertaken using a
triangular pressure distribution and the earth pressure coefficients provided in Table 1.
Flexible walls are those which are free to rotate or tilt (i.e., cantilevered walls or single anchored or propped
walls) and should be designed using an ‘active’ earth pressure coefficient (Ka). Where the walls are rigid and
cannot rotate or tilt, then an ‘at-rest’ earth pressure coefficient (K0) should be used.
Passive pressure (Kp) should be ignored where there is potential for in-ground services trenches (or similar)
in front of the wall.

Table 1: Lateral Earth Pressure Coefficients.

                                                   Lateral Earth Pressure Coefficients

                          Bulk        Friction
 Retained Material      Density        Angle
                        (kN/m3)      (degrees)        Kp           Ko            Ka



      Loose sand           17           27           2.66          0.55         0.37
Medium dense Sand          18           32           3.26          0.47          0.3
      Dense sand           19           37           4.02          0.4          0.25
  Very dense sand          21           42           5.05          0.33          0.2

If appropriate, an allowance of 10 kPa should be made for lateral stress induced by compaction plant
operating behind the walls. The effects of surcharge should be included by multiplying the vertical pressure
developed by the surcharge by the appropriate lateral earth pressure coefficient from Table 1.


J001873-001-R-Rev1                                                                                    Page 7

Page 10

Cambooya Pty Ltd

Drainage material behind the wall should be installed for the full height of the wall, for a width of at least
0.3 m. The material must be free draining and granular and have a perforated or slotted drainage pipe at the
heel of the wall to rapidly remove the water into the stormwater system. Alternatively, the wall will need to be
designed for the full hydrostatic pressure.

6.4     Drainage & Erosion Control
Site drainage should be designed to readily remove surface water and to prevent ponding of water.
Stormwater should be piped to an engineer-designed dissipation system. Concentrated surface water flows
(e.g., roof runoff) should be avoided.

7.0       STABILITY RISK ASSESSMENT
A qualitative slope stability risk assessment for the proposed structure has been carried out following the
AGS 2007 guidelines. The risk assessment relates to property. Relative levels of risk and their implications
are given in Table 2 below and the qualitative terminology (i.e., likelihood and consequence definitions) for
use in assessing risk to property are attached in Appendix C.
Table 2: Stability Risk Levels.
 Risk Level                     Example Implications(1)

                                    Unacceptable without treatment. Extensive detailed investigation and research,
                 VERY HIGH          planning and implementation of treatment options essential to reduce risk to
 VH
                 RISK               Low; may be too expensive and not practical. Work likely to cost more than
                                    value of property.
                                    Unacceptable without treatment. Detailed investigation, planning and
 H               HIGH RISK          implementation of treatment options required to reduce risk to Low. Work would
                                    cost a substantial sum in relation to the value of the property.
                                    May be tolerated in certain circumstances (subject to regulators’ approval) but
                 MODERATE           requires investigation, planning and implementation of treatment options to
 M
                 RISK               reduce risk to Low. Treatment options to reduce to Low risk should be
                                    implemented as soon as practicable.
 L               LOW RISK           Usually acceptable to regulators. Where treatment has been required to reduce
                                    the risk to this level, ongoing maintenance required.
                 VERY LOW
 VL                                 Acceptable. Manage by normal slope maintenance procedures.
                 RISK
Note: (1) The implications for a particular situation are to be determined by all parties to the risk assessment and may depend on the
nature of the property at risk; these are only given as a general guide.

Table 3: Qualitative Risk Assessment for Property (Based on AGS 2007).
                                                                 Assessed
          Hazard             Likelihood      Consequence                                           Comments
                                                                   Risk
                                                                                Shallow translational failure in the loose sands
      Shallow failure of                                                        is considered Rare, and if the
       soils above the                                                          recommendations in this report are
                                Rare         Insignificant       Very Low
     footing zone (< 2m                                                         implemented, the consequence to property is
            depth)                                                              assessed as Insignificant. The resulting
                                                                                assessed risk is Very Low.
                                                                                The likelihood of a deep failure through the
        Deeper failure                                                          dense (or denser) sand is assessed as Rare
     through soils below        Rare             Major              Low         based on the slope profile. Although the
        footing depth                                                           consequence of such a failure would likely be
                                                                                Major, the resultant risk is Low.
 Refer Appendix C, Qualitative Risk Analysis Matrix (Australian Geomechanics Vol 42 No 1 March 2007).

Subject to the implementation of the recommendations in this report, it is our opinion that there is a Very Low
to Low Risk of global instability of the remediated retaining structure assessed in accordance with the AGS
guidelines (March 2007).




J001873-001-R-Rev1                                                                                                      Page 8

Page 11

Cambooya Pty Ltd

7.1   General Foundation Maintenance
The Queensland Building and Construction Commission (QBCC): A guide to preventing structural damage
V3 (2015) is attached in Appendix D for your information. This advice should be considered in the
construction and maintenance of the proposed development.

8.0     LIMITATIONS
Your attention is drawn to the document, Limitations which is attached in Appendix E.




Core Consultants Pty Ltd
Yours sincerely,




Brodie Hare                                                     Darryn Quinn
MEngSc BEng(Hons) MIEAust CPEng NER RPEQ 29565                  BE(Geological) MIEAust RPEQ 7602
Senior Geotechnical Engineer                                    Associate/Principal Geotechnical Engineer

BH/GAH/DQ/bh


A.B.N. 75 603 384 050




J001873-001-R-Rev1                                                                             Page 9

Page 12

 

Appendix A
Site Plan

 

Page 13

                     7079405




                     7079400
                                                                                                  NE
                                                                                                LA
                                                                                        A   S
                                                                                   U GL
                     7079395
                                                                               DO
                                                                                                                      Breaks in slope


                     7079390

                                                                                                                                Small retaining wall
                                                                      BH1

                     7079385
                                                      3º
                                                                  19º


                     7079380                                            3º




                                                                                     BH2
      Northing (m)




                     7079375




                     7079370
                                                                                                        EXISTING BUILDING


                     7079365




                     7079360




                     7079355
                                                                                                                                                      ET
                                                                                                                                                   RE
                                                                                                                                               ST
                                                                                                                                          KE
                     7079350                                                                                                          DU



                     7079345




                     7079340
                               510980   510985   510990            510995          511000        511005         511010       511015       511020          511025   511030
                                                                                            Easting (m)


LEGEND
    Denotes approximate borehole location

 3º    Denotes slope angle and direction
                                                                                                     THIS DOCUMENT MUST BE READ IN CONJUCTION WITH CORE DOCUMENT J001873-001-L-Rev0.
                                                                                                                                                          BASE IMAGE FROM NEARMAP

                                                                                       DRAWN                               CLIENT:           CAMBOOYA PTY LTD
                                                                                                                BH
                                                                                       CHECKED                 GAH     PROJECT:
                                                               Scale (m)                                                  PROPOSED MIXED-USE DEVELOPMENT
                                                                                       DRAWN                21/02/2023    36-38 DUKE STREET, SUNSHINE BEACH
                                                  0        2      4        6   8       DATE
                                                                                       CHECKED              22/02/2023 TITLE:                       SITE PLAN
                                                                                       DATE
                                                                                       ORIGINAL                            PROJECT NO.:                     FIGURE NO.:         REV
                                                                                                                 A3                            J001873                    001          0
                                                                                       SIZE

Page 14

 

Appendix B
Reports of Boreholes and Explanatory Notes

 

Page 15

                                                                                                                                                                                                                                                                                                                                                                                      REPORT OF BOREHOLE: BH1
                                                                                                                                                                                                                                                                                                                                                     East            510993.0 m
                                                                                                                                                                                                                                                                                                                                                     North           7079386.0 m MGA94 Zone 56                                        Sheet                  1 OF 1
                                                                                                                                                                                                                             Client                            Cambooya Pty Ltd                                                                      Surface RL      18.36 m AHD                                                      Logged:                BH
                                                                                                                                                                                                                             Project                           Mixed-Use Development                                                                 Contractor      Core Consultants Pty Ltd                                         Logged Date:           09/02/23
                                                                                                                                                                                                                             Location                          36-38 Duke Street, Sunshine Beach                                                     Drill Rig       Edson CP1                                                        Checked:               GAH
                                                                                                                                                                                                                             Job No.                           J001873                                                                               Inclination     -90° Hole Dia. 100 mm                                            Checked Date:          22/02/23

                                                                                                                                                                                                                                            Drilling                                   Sampling                                                                                    Field Material Description




                                                                                                                                                                                                                                                                                                                            GROUP SYMBOL




                                                                                                                                                                                                                                                                                                                                                                                                            CONSISTENCY
                                                                                                                                                                                                                              PENETRATION




                                                                                                                                                                                                                                                                                                      RECOVERED
                                                                                                                                                                                                                                                                                                                                                                                                                                          DCP TEST
                                                                                                                                                                                                                              RESISTANCE




                                                                                                                                                                                                                                                                                                                                                                                                            CONDITION
                                                                                                                                                                                                                                                                                                                                                                                                            MOISTURE
                                                                                                                                                                                                                                                                                    SAMPLE OR




                                                                                                                                                                                                                                                                                                                  GRAPHIC
                                                                                                                                                                                                                    METHOD




                                                                                                                                                                                                                                                                                                                                                                                                            DENSITY
                                                                                                                                                                                                                                                                                                                                                    SOIL/ROCK MATERIAL DESCRIPTION                                                     Blows per 100 mm
                                                                                                                                                                                                                                                              (metres)
                                                                                                                                                                                                                                            WATER




                                                                                                                                                                                                                                                                                    FIELD TEST
                                                                                                                                                                                                                                                              DEPTH




                                                                                                                                                                                                                                                                                                                  LOG
                                                                                                                                                                                                                                                                         DEPTH                                                                                                                                            0       5           10     15       20   25
                                                                                                                                                                                                                                                                          RL
                                                                                                                                                                                                                                                                 0
                                                                                                                                                                                                                                                                         18.36                                              SP             TOPSOIL SAND trace silt trace gravel: fine grained, brown;
                                                                                                                                                                                                                                                                                                                                           gravel fine to medium grained, sub-angular; grass rootlets.             L
                                                                                                                                                                                                                                                                          0.20
                                                                                                                                                                                                                                                                         18.16                                              SP             SAND (AEOLIAN) trace silt trace gravel: fine grained, brown to
                                                                                                                                                                                                                                                                                                                                           pale brown; gravel fine to medium grained, sub-angular.

                                                                                                                                                                                                                                                                                                                                                                                                              D   MD


                                                                                                                                                                                                                                  L

                                                                                                                                                                                                                                                                                                                                                                                                                              Augered to this depth before
                                                                                                                                                                                                                                                                          1.00                                                                                                                                                commencing test
                                                                                                                                                                                                                                                                 1
                                                                                                                                                                                                                                                                         17.36                                              SP             SAND (AEOLIAN) with silt: fine grained, dark grey; tending to
                                                                                                                                                                                                                                                                                                                                           indurated sand.



                                                                                                                                                                                                                                                                          1.50
                                                                                                                                                                                                                                                                         16.86                                              SP             SAND (AEOLIAN) with silt: fine grained, dark grey; weakly
                                                                                                                                                                                                                                                                                                                                           cemented.




                                                                                                                                                                                                                                                                 2
CORE 2.01.1 LIB.GLB Log IS AU BOREHOLE 3 J001873-UNIT DEVELOPMENT-BH1-2.GPJ <<DrawingFile>> 21/2/2023 15:52 10.02.00.04 Datgel Lab and In Situ Tool - DGD | Lib: Core 2.01.1 2020-05-19 Prj: Core 2.00 2020-03-24




                                                                                                                                                                                                                                                                                                                                                                                                                              Augered to this depth before
                                                                                                                                                                                                                                                                                                                                                                                                             D-               recommencing test
                                                                                                                                                                                                                                                                                                                                                                                                             M


                                                                                                                                                                                                                                 M
                                                                                                                                                                                                                                            Not Encountered
                                                                                                                                                                                                                    ADT




                                                                                                                                                                                                                                                                 3




                                                                                                                                                                                                                                                                                                                                                                                                                  VD




                                                                                                                                                                                                                                                                          3.80
                                                                                                                                                                                                                                                                         14.56                                              SP             SAND (AEOLIAN) trace silt: fine to medium grained, brown
                                                                                                                                                                                                                                                                                                                                           and orange brown.
                                                                                                                                                                                                                                                                 4

                                                                                                                                                                                                                               L-M



                                                                                                                                                                                                                                                                          4.50
                                                                                                                                                                                                                                                                         13.86                                              SP             SAND (AEOLIAN) with silt: fine grained, dark grey; weakly
                                                                                                                                                                                                                                                                                                                                           cemented.


                                                                                                                                                                                                                                                                                                                                                                                                             M
                                                                                                                                                                                                                                                                 5


                                                                                                                                                                                                                                 M


                                                                                                                                                                                                                                                                          5.50
                                                                                                                                                                                                                                                                         12.86                                              SM             Silty SAND (AEOLIAN): fine grained, dark brown.




                                                                                                                                                                                                                                                                                                                                                                                                                              Augered to this depth before
                                                                                                                                                                                                                                                                          6.00                                                                                                                                                recommencing test
                                                                                                                                                                                                                                                                 6
                                                                                                                                                                                                                                                                                                                                           Hole Terminated at 6.00 m
                                                                                                                                                                                                                                                                                                                                           Target depth
                                                                                                                                                                                                                                                                                                                                           Backfilled




                                                                                                                                                                                                                                                                              This report must be read in conjunction with accompanying notes and abbreviations. It has been prepared for geotechnical
                                                                                                                                                                                                                                                                            purposes only, without attempt to consider possible contamination. Any references to potential contamination are for information
                                                                                                                                                                                                                                                                                          only and do not necessarily indicate the presence or absence of soil or groundwater contamination.

Page 16

                                                                                                                                                                                                                                                                                                                                                   REPORT OF HAND AUGER BOREHOLE: BH2
                                                                                                                                                                                                                                                                                                                                                     East           510998.0 m
                                                                                                                                                                                                                                                                                                                                                     North          7079376.0 m MGA94 Zone 56                                          Sheet               1 OF 1
                                                                                                                                                                                                                             Client                            Cambooya Pty Ltd                                                                      Surface RL     15.90 m AHD                                                        Logged:             BH
                                                                                                                                                                                                                             Project                           Mixed-Use Development                                                                 Contractor     Core Consultants Pty Ltd                                           Logged Date:        09/02/23
                                                                                                                                                                                                                             Location                          36-38 Duke Street, Sunshine Beach                                                     Drill Rig      Hand Auger                                                         Checked:            GAH
                                                                                                                                                                                                                             Job No.                           J001873                                                                               Inclination    -90° Hole Dia. 50 mm                                               Checked Date:       22/02/23

                                                                                                                                                                                                                                            Drilling                                   Sampling                                                                                     Field Material Description




                                                                                                                                                                                                                                                                                                                            GROUP SYMBOL




                                                                                                                                                                                                                                                                                                                                                                                                           CONSISTENCY
                                                                                                                                                                                                                              PENETRATION




                                                                                                                                                                                                                                                                                                      RECOVERED
                                                                                                                                                                                                                                                                                                                                                                                                                                           DCP TEST
                                                                                                                                                                                                                              RESISTANCE




                                                                                                                                                                                                                                                                                                                                                                                                           CONDITION
                                                                                                                                                                                                                                                                                                                                                                                                           MOISTURE
                                                                                                                                                                                                                                                                                    SAMPLE OR




                                                                                                                                                                                                                                                                                                                  GRAPHIC
                                                                                                                                                                                                                    METHOD




                                                                                                                                                                                                                                                                                                                                                                                                           DENSITY
                                                                                                                                                                                                                                                                                                                                                    SOIL/ROCK MATERIAL DESCRIPTION                                                      Blows per 100 mm
                                                                                                                                                                                                                                                              (metres)
                                                                                                                                                                                                                                            WATER




                                                                                                                                                                                                                                                                                    FIELD TEST
                                                                                                                                                                                                                                                              DEPTH




                                                                                                                                                                                                                                                                                                                  LOG
                                                                                                                                                                                                                                                                         DEPTH                                                                                                                                           0         5           10     15    20   25
                                                                                                                                                                                                                                                                          RL
                                                                                                                                                                                                                                                                 0
                                                                                                                                                                                                                                                                         15.90                                              SM             TOPSOIL Silty SAND: fine grained, dark brown; grass rootlets.



                                                                                                                                                                                                                                                                          0.40
                                                                                                                                                                                                                                                                                                                                                                                                                  L
                                                                                                                                                                                                                                                                         15.50                                              SP             SAND (AEOLIAN) trace silt: fine grained, brown.
                                                                                                                                                                                                                                  L
                                                                                                                                                                                                                                            Not Encountered
                                                                                                                                                                                                                    HA




                                                                                                                                                                                                                                                                                                                                                                                                             D
                                                                                                                                                                                                                                                                                                                                                                                                                 MD /
                                                                                                                                                                                                                                                                                                                                                                                                                  D
                                                                                                                                                                                                                                                                 1
                                                                                                                                                                                                                              M-H                                                                                                                                                                                 D
                                                                                                                                                                                                                                                                          1.20
                                                                                                                                                                                                                                                                         14.70                                                             Dark brown; tending to indurated sand.
                                                                                                                                                                                                                                                                                                                                                                                                                             >20
                                                                                                                                                                                                                                 H                                                                                                                                                                               VD

                                                                                                                                                                                                                                                                          1.60
                                                                                                                                                                                                                                                                                                                                           Hole Terminated at 1.60 m
                                                                                                                                                                                                                                                                                                                                           Practical Refusal
                                                                                                                                                                                                                                                                                                                                           Backfilled

                                                                                                                                                                                                                                                                 2
CORE 2.01.1 LIB.GLB Log IS AU BOREHOLE 3 J001873-UNIT DEVELOPMENT-BH1-2.GPJ <<DrawingFile>> 21/2/2023 15:53 10.02.00.04 Datgel Lab and In Situ Tool - DGD | Lib: Core 2.01.1 2020-05-19 Prj: Core 2.00 2020-03-24




                                                                                                                                                                                                                                                                 3




                                                                                                                                                                                                                                                                 4




                                                                                                                                                                                                                                                                 5




                                                                                                                                                                                                                                                                 6




                                                                                                                                                                                                                                                                              This report must be read in conjunction with accompanying notes and abbreviations. It has been prepared for geotechnical
                                                                                                                                                                                                                                                                            purposes only, without attempt to consider possible contamination. Any references to potential contamination are for information
                                                                                                                                                                                                                                                                                          only and do not necessarily indicate the presence or absence of soil or groundwater contamination.

Page 17

                                              EXPLANATION OF NOTES, ABBREVIATIONS & TERMS
                                              USED ON BOREHOLE AND TEST PIT REPORTS
DRILLING/EXCAVATION METHOD
AS       Auger Screwing                  RD             Rotary blade or drag bit                  NQ           Diamond Core - 47 mm
AD       Auger Drilling                  RT             Rotary Tricone bit                        NMLC         Diamond Core - 52 mm
*V       V - Bit                         RAB            Rotary Air Blast                          HQ           Diamond Core - 63 mm
T        TC - Bit, e.g. ADT              RC             Reverse Circulation                       HMLC         Diamond Core – 63mm
HA       Hand Auger                      PT             Push Tube                                 BH           Tractor Mounted Backhoe
ADH      Hollow Auger                    CT             Cable Tool Rig                            EX           Tracked Hydraulic Excavator
DTC      Diatubre Coring                 JET            Jetting                                   EE           Existing Excavation

WB       Washbore or Bailer              NDD            Non-destructive digging                   HAND         Excavated by Hand Methods

PENETRATION/EXCAVATION RESISTANCE
L        Low resistance . Rapid penetration possible with little effort from the equipment used
M        Medium resistance. Excavation possible at an acceptable rate with moderate effort from equipment used
H        High resistance to penetration/excavation. Further penetration is possible at a slow rate
R        Refusal or Practical Refusal. No further progress possible without the risk of damage or unacceptable wear to the digging implement
         or machine.
These assessments are subjective and are dependent on many factors including the equipment power, weight, condition of excavation or drilling tools,
and the experience of the operator.

WATER
                               Water level shown at date                                                 Partial water loss
                               Water inflow                                                              Complete water loss
GROUNDWATER NOT                The observation of groundwater whether present or not, was not possible due to drilling water, surface seepage or cave in
OBSERVED                       of the borehole/test pit.
GROUND WATER NOT               The borehole/test pit was dry soon after excavation. However, groundwater could be present in less permeable strata.
ENCOUNTERED                    Inflow may have been observed had the borehole/test pit been left open for a longer period.
SAMPLING AND TESTING
SPT                   Standard Penetration Test to AS1289.6.3.1-2004
4,7,11 N=18           4,7,11 = Blows per 150mm            N = Blows per 300mm penetration following 150mm seating
30/80mm                 Where practical refusal occurs, the blows and penetration for that interval are reported
RW                    Penetration occurred under the rod weight only
HW                    Penetration occurred under the hammer and rod weight only
HB                    Hammer double bouncing on anvil
DS                    Disturbed Sample
BDS                   Bulk disturbed sample
G                     Gas Sample
W                     Water sample
FP                    Field permeability test over section noted
FV                    Field vane shear test expressed as uncorrected shear strength (sv = peak value)
PID                   Photoionisation Detector reading in ppm
PM                    Pressuremeter test over section noted
PP                    Pocket penetrometer test expressed as instrument reading in kPa
U63                   Thin walled tube sample - number indicates nominal sample diameter in millimetres
WPT                   Water pressure tests
DCP                   Dynamic cone penetration test
CPT                   Dynamic cone penetration test

CPTu                  Static cone penetration test with pore pressure (u) measurement

ROCK CORE RECOVERY

        TCR = Total Core Recovery (%)                         SCR = Solid Core Recovery (%)                        RQD = Rock Quantity Designation (%)

Page 18

                                            METHOD OF SOIL DESCRIPTION USED ON BOREHOLE AND TEST PIT
                                            REPORTS
                           FILL                                                          CLAY (CL,CI, or CH)

                           GRAVEL (GP or SW)                                             ORGANIC SOILS (OL or OH or Pt)


                           SAND (SP or SW)                                               COBBLES or BOULDERS

                           SILT (ML or MH)

Combinations of these basic symbols may be used to indicate mixed materials such as sandy clay.

CLASSIFICATION AND INFERRED STRATIGRAPHY
Soil and Rock is classified and described in Reports of Boreholes and Test Pits using the preferred method given in AS 1726 - 2017. The material proper-
ties are assessed in the field by visual/tactile methods.

                         PARTICLE SIZE                                                                  PLASTIC PROPERTIES

      Major
                    Sub Division               Particle Size
     Division

               Boulders                          >200 mm

               Cobbles                         63 - 200 mm

      Gravel              Coarse               20 - 63 mm

      Gravel             Medium                6.7 - 20 mm

      Gravel               Fine               2.36 - 6.7 mm

      Sand                Coarse              0.6 - 2.36 mm

      Sand               Medium               0.21 - 0.6 mm

      Sand                 Fine             0.075 - 0.21 mm


                 Silt                    0.002 - 0.075 mm

                Clay                           <0.002 mm

MOISTURE CONDITION FOR COARSE GRAINED SOIL                        AS 1726 - 2017

Symbol             Term                                           Description

D                  Dry                                            Non-cohesive and free running

M                  Moist                                          Soil feels cool, darkened in colour, tends to stick together

W                  Wet                                            Soil feels cool, darkened in colour, soil sticks together, free water forms when handling

MOISTURE CONDITION FOR FINE GRAINED SOIL                          AS1726 - 2017


Symbol             Term                                           Description
W<PL               Moist dry of liquid limit                      Hard and friable or powdery
W = PL             Moist near plastic limit                       Soils can be molded at a moisture condition approximately equal to the plastic limit
W >PL              Moist, wet of plastic limit                    Soils usually weakened and free water forms on hands when handling
W = LL             Wet near plastic limit
W > LL             Wet, wet of liquid limit
CONSISTENCY TERMS FOR                           AS1726—2017           RELATIVE DENSITY OF COARSE GRAINED SOILS                                   AS1726—2017
COHESIVE SOILS
                                                                      Symbol                 Term                      Density Index %           SPT ‘N’ #
Symbol           Term                           Undrained Shear
                                                                      VL                     Very Loose                Less than 15              0 to 4
                                                Strength
                                                                      L                      Loose                     15 to 35                  4 to 10
VS               Very Soft                      0 to 12 kPa

S                Soft                           12 to 25 kPa          MD                     Medium Dense              35 to 65                  10 to 30

F                Firm                           25 to 50 kPa          D                      Dense                     65 to 85                  30 to 50

St               Stiff                          50 to 100 kPa         VD                     Very Dense                Above 85                  Above 50

VSt              Very Stiff                     100 to 200 kPa        In the absence of test results, consistency and density may be assessed from correlations with
                                                                      the observed behaviour of the material.
H                Hard                           Above 200 kPa

Page 19

                                              TERMS FOR ROCK MATERIAL STRENGTH & WEATHERING AND
                                              ABBREVIATIONS FOR DEFECT DESCRIPTIONS
ROCK MATERIAL STRENGTH CLASSIFICATION                                 AS1726—2017

Symbol          Term               Uniaxial         Point Load                                                Field Guide
                                                   Strength Is (50)
                                Compressive
                                                       (MPa)
                               Strength (MPa)
VL        Very Low             0.6 to 2            0.03 to 0.1        Material crumbles under firm blows with sharp end of pick. Pieces up to 30 mm thick can
          Strength                                                    be broken with finger pressure.

L         Low Strength         2 to 6              0.1 to 0.3         Easily scored with knife. Indentations 1 mm to 3 mm show in the specimen with firm
                                                                      blows of the pick point. A piece of core 150 mm by 50 mm may be broken by hand. Sharp
                                                                      edges of core are friable and break during handling.

M         Medium               6 to 20             0.3 to 1           Readily scored with a knife. A piece of core 150 mm by 50 mm can be broken by hand
          Strength                                                    with difficulty.

H         High Strength        20 to 60            1 to 3             A piece of core 150 mm by 50 mm cannot be broken by hand but can be broken by a pick
                                                                      with a single firm blow. Rock rings under hammer.

VH        Very High            60 to 200           3 to 10            Hand specimen breaks with pick after more than one blow. Rock rings under hammer.
          Strength

EH        Extremely High       Above 200           Above 10           Specimen requires many blows with geological pick to break through intact material. Rock
          Strength                                                    rings under hammer.

       = Diametral Point Load Test                  = Axial Point Load Test

CLASSIFICATION OF MATERIAL                        AS1726—2017
WEATHERING
     Symbol                   Term                                                                  Field Guide
RS                  Residual Soil (Note 1)        Material is weathered to such an extent that it has soil properties. Mass structure and material texture and
                                                  fabric of original rock are no longer visible but the soil has not been significantly transported.

XW                  Extremely Weathered           Material is weathered to such an extent that is has soil properties. Mass structure and material texture and
                    (Note 1)                      fabric of original rock are still visible.

HW                  Highly Weathered (Note 2) The whole rock mass is discoloured, usually by iron staining or beaching to the extent that the colour of the
                                              original rock is not recognizable. Rock strength is significantly changed by weathering. Some primary miner-
                                              als have weathered to clay minerals. Porosity may be increased by leaching, or may be decreased due to
                                              deposition of weathering products in pores.

MH                  Moderately Weathered          The whole of the rock material is discoloured, usually by iron staining or bleaching to the extent that the
                    (Note 2)                      colour of the original rock is not recognizable, but shows little or no change in strength from fresh rock.

SW                  Slightly Weathered            Pock is partially discoloured with staining or bleaching along joints but shows little or no change of strength
                                                  from fresh rock.

FR                  Fresh                         Rock shows no signs of decomposition of individual minerals or colour change.

Note 1              The term ‘Extremely Weathered rock’ is misleading as the material has soil properties. The word ‘rock’ should be replaced with the name
                    of the original rock of the word ‘material’, eg. Extremely Weathered granite or Extremely Weathered material.

Note 2              Where it is not possible to distinguish between ‘Highly Weathered’ and ‘Moderately Weathered’ rock the term ‘Distinctly Weathered’ may
                    be used.
                       DEFECT TYPE/DESCRIPTION                                           DEFECT PROFILE                          DEFECT ROUGHNESS
                                                                               Symbol               Description                       DESCRIPTION
B           Bedding Parting               V           Vein
                                                                               PL                   Planar
                                                                                                                         Symbol               Description
J           Joint                         HB/DB       Handling/Drilling        St                   Stepped
                                                      Break                                                              Sl                   Slickenside
                                                                               Un                   Undulating
EW          Extremely Weathered           C           Contact                                                            Sm                   Smooth
                                                                                    DEFECT INFILL DESCRIPTION
            Seam
                                                                               Symbol               Description          Ro                   Rough
FZ          Fracture Zone                 L           Cleavage                                                           Vertical Boreholes - The dip
                                                                               Cn                   Clean: No visible
                                                                                                    coating              (inclination from horizontal) for the
CZ/S        Crushed Zone/Seam             X           Foliation                                                          defect is given.
                                                                               Sn                   Stain: Coated 1 to
                                                                                                    3 mm               Inclined Boreholes - The inclination
IS          Infilled Seam                 S           Schistocity                                                      is measured as the acute angle to the
                                                                               Vr                   Veneer: < 1 mm     core axis.
SZ/S        Sheared Zone/Seam                                                  Ct                   Coating: 1 to 3
                                                                                                    mm

Page 20

 

Appendix C
Qualitative Terminology for Use in Assessing
Risk to Property (AGS 2007)

 

Page 21

                                      PRACTICE NOTE GUIDELINES FOR LANDSLIDE RISK MANAGEMENT 2007
                                                              APPENDIX C: LANDSLIDE RISK ASSESSMENT
                                    QUALITATIVE TERMINOLOGY FOR USE IN ASSESSING RISK TO PROPERTY


   QUALITATIVE MEASURES OF LIKELIHOOD

Approximate Annual Probability
                                             Implied Indicative Landslide
                                                                                                                     Description                                           Descriptor               Level
Indicative          Notional                    Recurrence Interval
  Value             Boundary
   10-1                5x10-2
                                              10 years                           The event is expected to occur over the design life.                                ALMOST CERTAIN                   A
                                                                    20 years     The event will probably occur under adverse conditions over the
        -2
   10                                      100 years
                                                                                 design life.
                                                                                                                                                                     LIKELY                           B
                            -3
     -3               5x10                                       200 years
   10                                      1000 years                            The event could occur under adverse conditions over the design life.                POSSIBLE                         C
                      5x10-4                                     2000 years
                                                                                 The event might occur under very adverse circumstances over the
   10-4                                   10,000 years
                                                                                 design life.
                                                                                                                                                                     UNLIKELY                         D
     -5               5x10-5                                     20,000 years
   10                                                                            The event is conceivable but only under exceptional circumstances
                                         100,000 years                                                                                                               RARE                             E
                                                                                 over the design life.
     -6                5x10-6                                    200,000 years
   10                                   1,000,000 years                          The event is inconceivable or fanciful over the design life.                        BARELY CREDIBLE                  F
   Note:     (1)   The table should be used from left to right; use Approximate Annual Probability or Description to assign Descriptor, not vice versa.


   QUALITATIVE MEASURES OF CONSEQUENCES TO PROPERTY

  Approximate Cost of Damage
                                                                                               Description                                                                 Descriptor               Level
Indicative           Notional
  Value              Boundary
                                         Structure(s) completely destroyed and/or large scale damage requiring major engineering works for
   200%                                                                                                                                                             CATASTROPHIC                      1
                                         stabilisation. Could cause at least one adjacent property major consequence damage.
                     100%
                                         Extensive damage to most of structure, and/or extending beyond site boundaries requiring significant
   60%                                                                                                                                                              MAJOR                             2
                                         stabilisation works. Could cause at least one adjacent property medium consequence damage.
                       40%
                                         Moderate damage to some of structure, and/or significant part of site requiring large stabilisation works.
   20%                                                                                                                                                              MEDIUM                            3
                                         Could cause at least one adjacent property minor consequence damage.
                       10%
    5%                 1%                Limited damage to part of structure, and/or part of site requiring some reinstatement stabilisation works.                 MINOR                             4
                                         Little damage. (Note for high probability event (Almost Certain), this category may be subdivided at a
   0.5%                                                                                                                                                             INSIGNIFICANT                     5
                                         notional boundary of 0.1%. See Risk Matrix.)
   Notes:    (2)   The Approximate Cost of Damage is expressed as a percentage of market value, being the cost of the improved value of the unaffected property which includes the land plus the
                   unaffected structures.
             (3)   The Approximate Cost is to be an estimate of the direct cost of the damage, such as the cost of reinstatement of the damaged portion of the property (land plus structures), stabilisation
                   works required to render the site to tolerable risk level for the landslide which has occurred and professional design fees, and consequential costs such as legal fees, temporary
                   accommodation. It does not include additional stabilisation works to address other landslides which may affect the property.
             (4)   The table should be used from left to right; use Approximate Cost of Damage or Description to assign Descriptor, not vice versa


   91                                                          Australian Geomechanics Vol 42 No 1 March 2007

Page 22

                                        PRACTICE NOTE GUIDELINES FOR LANDSLIDE RISK MANAGEMENT 2007
                APPENDIX C: – QUALITATIVE TERMINOLOGY FOR USE IN ASSESSING RISK TO PROPERTY (CONTINUED)


      QUALITATIVE RISK ANALYSIS MATRIX – LEVEL OF RISK TO PROPERTY
                      LIKELIHOOD                                                  CONSEQUENCES TO PROPERTY (With Indicative Approximate Cost of Damage)
                                           Indicative Value of         1: CATASTROPHIC                 2: MAJOR                3: MEDIUM                4: MINOR                    5:
                                          Approximate Annual                 200%                         60%                      20%                     5%                INSIGNIFICANT
                                              Probability                                                                                                                         0.5%
A –    ALMOST CERTAIN                              10-1                          VH                         VH                      VH                       H                   M or L (5)
                                                     -2
B -    LIKELY                                      10                            VH                         VH                       H                       M                       L
C -    POSSIBLE                                    10-3                          VH                          H                       M                       M                      VL

D -    UNLIKELY                                    10-4                           H                         M                        L                       L                      VL
                                                     -5
E -    RARE                                        10                             M                          L                       L                      VL                      VL
                                                     -6
F -    BARELY CREDIBLE                             10                             L                         VL                      VL                      VL                      VL
      Notes:    (5)   For Cell A5, may be subdivided such that a consequence of less than 0.1% is Low Risk.
                (6)   When considering a risk assessment it must be clearly stated whether it is for existing conditions or with risk control measures which may not be implemented at the current
                      time.


      RISK LEVEL IMPLICATIONS
                         Risk Level                                                                                  Example Implications (7)
                                                                  Unacceptable without treatment. Extensive detailed investigation and research, planning and implementation of treatment
           VH                    VERY HIGH RISK                   options essential to reduce risk to Low; may be too expensive and not practical. Work likely to cost more than value of the
                                                                  property.
                                                                  Unacceptable without treatment. Detailed investigation, planning and implementation of treatment options required to reduce
           H                          HIGH RISK
                                                                  risk to Low. Work would cost a substantial sum in relation to the value of the property.
                                                                  May be tolerated in certain circumstances (subject to regulator’s approval) but requires investigation, planning and
           M                     MODERATE RISK                    implementation of treatment options to reduce the risk to Low. Treatment options to reduce to Low risk should be
                                                                  implemented as soon as practicable.
                                                                  Usually acceptable to regulators. Where treatment has been required to reduce the risk to this level, ongoing maintenance is
           L                          LOW RISK
                                                                  required.
                                                                  Acceptable. Manage by normal slope maintenance procedures.
           VL                     VERY LOW RISK

       Note:    (7)   The implications for a particular situation are to be determined by all parties to the risk assessment and may depend on the nature of the property at risk; these are only
                      given as a general guide.




      92                         Australian Geomechanics Vol 42 No 1 March 2007

Page 23

 

Appendix D
A Guide to Preventing Structural Damage V3
(QBCC 2015)

 

Page 24

 

A guide to preventing
structural damage

Build better.

Page 25

Home owners guide to planning
landscaping and maintenance
of foundations
Structural damage can result from        - under normal conditions. The
movement in clay soils caused by         performance of footings under this
varying moisture conditions around the   standard requires normal conditions to
perimeter of homes.                      be maintained around the house.
The majority of Queensland homes         This guideline identifies abnormal
are situated on what are termed          conditions that should be avoided
reactive clay soils. These soils are     and/or corrected.
subject to expansion and contraction     Dry seasons cause soils to dry out
depending on seasonal weather and        rapidly. Wet seasons cause soils to
site conditions. Sandy sites and rocky   become wet quickly. This results in
terrain are usually not prone to this    sudden extreme volume changes and
expansion and contraction.               movement in soil.
In Queensland, engineers design          Abnormal conditions (other than
footings to the Australian Standard      seasonal changes), may include the
AS2870 – 2011 Residential slabs          effect of trees, poor surface drainage
and footings. Footings correctly         and/or leaking plumbing. If not allowed
designed to this standard are intended   for in the engineer’s design, these
to accommodate the expected              types of abnormal conditions may lead
movements caused by seasonal             to movement and damage varying
volume changes in the soil (swelling     from minor to extreme.
when wet and shrinking when dry)



  NORMAL MOVEMENT EXPECTATIONS FOR BUILDINGS CONSTUCTED
  ON REACTIVE CLAY SOILS

Page 26

How much can the soils under my
house move?
The amount of movement that may occur depends on the site classification,
which is defined under the Australian Standard AS2870.
The relevant classifications and expected movements under normal site
conditions and seasonal influences are:


Site             Description of type of clay and reactivity                   Expected range of
classification                                                                movement
      A          Mostly sand and rock with little or no ground movement       0
                 from moisture changes.
      S          Slightly reactive clays that do not present significant      0 to 20mm
                 trouble. Very limited damage could be expected in the life
                 of the building.
      M          Moderately reactive clays that may cause minor               20 to 40mm
                 movement and damage in the life of the building.
                 Reasonable care is required in planning the site.
      H          Highly reactive clays have potential to move more, and       H1 40 to 60mm
  (H1 & H2)      react to variable moisture change conditions. Some minor
                 damage may occur in the life of the building under normal
                                                                              H2 60 to 75mm
                 conditions. More significant damage may occur where site
                 maintenance conditions are a problem e.g. influence of
                 trees or leaking underground plumbing or poor drainage.
                 Particular care is required in planning the site.
      E          Extremely reactive clays have the potential to react         >75mm
                 significantly to any variable moisture changes in the
                 foundation clays and require significant attention to
                                                                              (Note: Movements
                 detail in planning the site works. Extreme movement and
                                                                              on E sites have been
                 damage may occur if the site conditions and foundation
                                                                              known to move up
                 maintenance requirements are not observed. Footing
                                                                              to and in excess
                 systems and site conditions on “E” sites require very
                                                                              of 100 to 150mm
                 detailed specification from an engineer.
                                                                              in SE Qld)

Page 27

Is it normal to expect cracking
to occur in brickwork, walls
and ceilings?
Yes, damage in varying degrees can
be expected in the life of the building     Key points to consider when
depending on the relevant site              planning landscaping to avoid
classification.                             structural damage.
If cracking becomes apparent the site       •   Plan type and location of
maintenance conditions should be                gardens, paths, driveways,
checked as noted under “key points              lawns, filling and retaining walls
to consider...”                             •   Take care in selection of trees
Corrective action should be carried out         and shrubs. Do not over plant
immediately and may include regrading           next to the house
surface drainage, moving gardens and        •   Keep trees with high water
trees or repairing leaks in water supply,       demand well away from
stormwater and/or sewer drainage.               buildings in reactive clay areas.
A sound plan for a reactive clay site       •   Avoid variable conditions
is to provide a consistent moisture             around the house and maintain
regime around the building by installing        adequate moisture/watering.
paths and patios against the house.             Do not over water and avoid
Locate lawns up against paths & patios.         the use of unregulated
Garden beds, the most heavily watered           sprinkler systems.
parts of a garden, should be kept well
                                            •   Locate ponds and water
away from the house.
                                                features away from the house.
If gardens must be placed in close
                                            •   Direct surface water away from
proximity to the house, they should be
                                                the house. Do not allow water
sealed with plastic and contain only
                                                to be trapped or pond near
a few small plants. Take care not to
                                                the house.
trap water against the building if using
garden edging.                              •   Repair leaking pipes and taps.
Caution: Care should also be taken if       Note: these issues should be
placing filling against the house. Always   considered as part of planning
ensure weep holes are not covered           and maintaining the home. Aim
and that existing Termite Management        to provide a consistent moisture
Systems are not compromised.                regime around the house. This will
                                            minimise soil moisture variations
                                            that may cause movement and
                                            result in structural damage.

Page 28

Common sense guidelines for
landscaping and gardens
1. Gardens
Important: It is quite impractical to try          If gardens must be placed in close
to prevent gardening activities from               proximity to the house, they should be
increasing the moisture content                    sealed with plastic and contain only
around the foundations of your                     a few small plants. Take care not to
home. The only practical course is to              trap water against the building if using
keep such activities away from the                 garden edging.
immediate vicinity of the building and             Caution: Care should also be taken
so minimise their effects.                         if placing filling against the house.
A sound plan for a reactive clay site              Always ensure weep holes are not
is to provide a consistent moisture                covered and that existing Termite
regime around the building by installing           Management Systems are not
paths and patios against the house.                compromised.
Locate lawns up against paths & patios.
Garden beds, the most heavily watered
parts of a garden, should be kept well
away from the house.




 RECOMMENDED LAYOUT FOR GARDENS AND LANDSCAPING

 TREES  AND
 Trees and   GARDEN
           garden bedsBEDS REQUIRING
                       requiring        HEAVY WATERING
                                 heavy watering            SHOULD
                                                should be kept       BE KEPT from
                                                               well removed   WELL  REMOVED
                                                                                  the dwelling.
 FROM THE DWELLING.

Page 29

2. Paths, patios and driveways
Paths should be laid hard against         Concrete pavements should be
brickwork or footings with a fall away    constructed in a way that will not
from the house to a stormwater            impede surface water flowing away
discharge point.                          from the building or cause water to
Avoid placing large expanses of           pond adjacent to the footings causing
concrete on one side of the house         clay foundations to swell.
and heavily watered garden beds           On “H” & “E” site classifications,
on the other.                             particular detail is required to prevent
The water saturated clay in the gardens   pavement from moving away from
will expand and swell while the soil      the building. Movement in paths could
under the concrete may not move.          cause stress on pipes and inspection
Structural damage can result from         openings and/or breakages in pipes.
this unco-ordinated movement.             Resulting leakages may cause
                                          movement and damage as a result of
                                          clay soils under the house swelling.


 RECOMMENDED LANDSCAPING

Page 30

3. Lawns                                     5. Excessive watering of gardens
If placing lawn areas against the house,     and lawns
ensure that filling built up against the
                                             The erection of a building also
wall is graded away and will not allow
                                             indirectly brings with it changes in the
ponding of water to occur. The filling
                                             moisture content to the site. While it
should be impervious clay soil and not
                                             is normal to water gardens and lawns,
sandy loam.
                                             excessive or over watering should be
REMEMBER: Do not cover weep holes.           avoided. Consistent and adequate
                                             watering should be observed at all
4. Filling                                   times.
Prior to preparing for gardens, lawns or     The location of sprinkler systems next
filling as part of site works, care should   to houses should also be avoided on
be taken to ensure the sub-grade or          H and E sites.
ground level is graded or sloped away,       Sprinkler systems should be as well
especially when filling or top dressing      controlled and maintained as practical,
with sandy loam. The sub-grade should        and only used in gardens and on lawns
consist of impervious natural site clay.     away from the building.
Where elevated floors exist ensure that
the final finished ground level outside
the house is not higher than the sub-
floor area and that water cannot flow
back under the house.

Page 31

6. Site drainage and sloping sites
Design for site conditions, location of
retaining walls, paths, swimming pools,
future structures or proposed extensions
etc. should all be considered when
preparing the site for correct surface
water flow.
If the ground slopes towards the house,
paths with spoon drains should be
provided.
It is also important to place drains uphill
of the footings so as to direct water
around the house and away from the
footings. A stormwater and roof water         Seek advice from an engineer
drainage management plan should be
                                              1. To ascertain surface falls which
considered and take into account water
                                                  allow for the specific potential
flowing from adjoining properties.
                                                 soil movement of the site without
                                                 loss of free drainage
                                              2. To provide correct mechanical
                                                  connection of perimeter paths
                                                  of footings



  RECOMMENDED DRAINAGE AND
  MAINTENANCE ADJACENT TO DWELLING

Page 32

7. Trees and shrubs
The roots of trees and shrubs can         Height of Tree(h)
affect footings by removing moisture      Distance from house (d)
from clay soils immediately underneath    d = 1 h for class H and M sites.
the building causing subsidence as the
                                          d = 1.5 h for class E sites.
clays shrink.
                                          d = 2 h for rows or groups of trees.
In its search for water, a tree root
system can spread a lateral distance       10 to 20      20 to 30        30 to 60
equal to the height of the tree. If in     metres        metres          metres
rows or grouped with other trees the         Acacias     But-But         Blue Gum
roots may spread up to twice the
                                               Ash       Cedars          Cypress
height of the tree.
                                            Athel Tree   English Oak     English Elm
Care should be taken when selecting
trees and, as a guide, the trees listed     Candlebark   Lemon Gum       Figs
should not be planted within the           Manna Gum     Palms           Karri
distance of their mature height from       Pepper tree   Planes          Pines
the house depending on the site
                                             Willows     Sheoaks         Poplars
classification and whether they are to
be planted in a line or in a group.            Yate      Silky Oak       River Gum
                                           Yellow Gum    Spotted         Sugar
                                                         Gum
                                                         Casuarina



  TREES AND SHRUBS

Page 33

Summary of owner responsibilities
for houses under warranty
1. Maintain the site drainage at all times.   5.Do not plant trees within a distance
2.Do not alter the site drainage provided        from a building that equates to
   by the builder. Any changes to the site        their mature height. Always plant in
   drainage should ensure that water will         accordance with the requirements for
   be directed away from the building             the relevant site classification.
   and not pond adjacent to the footing        6.Regularly check and maintain
   and slab system. Care should also be           plumbing, drainage and stormwater
   taken to avoid directing water flow to         systems by immediately carrying
   adjoining properties.                          out repairs to leakages or breakages
3.Where possible on reactive clay sites          when observed (usually displayed by
   (Type M,H,E Classifications), avoid            seepage and/or greener lawns etc.),
   placing gardens or installing garden           or when minor damage or cracking
   edging, gravel pavements etc next to           exceeding 3-5mm appears in walls
   the building. This may cause water             or ceilings.
   retention and/or promote a greater          By observing these requirements,
   variation in moisture conditions            movement and damage which may be
   around the building.                        expected in the life of the building can
4.Installation of sprinkler systems           be minimised and maintained within
   next to dwellings on highly and             normal performance requirements.
   extremely reactive sites (Type H & E
   Classifications) should be avoided.
   Adequate and consistent watering
   only is recommended. Over watering
   should be avoided.


   UNSATISFACTORY METHOD
   FOR CREATING SURFACE FALL
   AWAY FROM DWELLING

Page 34

Notes:




Note: this document has been developed to provide homeowners with general guidance on the
maintenace of their homes. It does not purport to address site specific issues. Homeowners should
seek professional advice from their builder or engineer when they experience movement in their
home or need advice on issues which may affect their home.

Page 35

Need more information?
Visit qbcc.qld.gov.au or call us on 139 333.




                                                                 QBCC20150210_FCTbrstructuraldamageV3




                                               299 Montague Road,
                                                 West End Qld 4101
                                                    GPO Box 5099,
                                                Brisbane Qld 4001
                                                         T: 139 333
                                                   F: 07 3225 2999
                                                W: qbcc.qld.gov.au

Page 36

 

Appendix E
Limitations

 

Page 37

                                             LIMITATIONS

This Document has been provided by Core Consultants Pty Ltd (“Core”) subject to the following
limitations:

This Document has been prepared for the particular purpose outlined in Core’s proposal and no
responsibility is accepted for the use of this Document, in whole or in part, in other contexts or for
any other purpose.

The scope and the period of Core’s Services are as described in C o r e ’s proposal, and are
subject to restrictions and limitations. Core did not perform a complete assessment of all possible
conditions or circumstances that may exist at the site referenced in the Document. If a service
is not expressly indicated, do not assume it has been provided. If a matter is not addressed, do not
assume that any determination has been made by Core in regards to it.

Conditions may exist which were undetectable given the limited nature of the enquiry Core was
retained to undertake with respect to the site. Variations in conditions may occur between
investigatory locations, and there may be special conditions pertaining to the site which have not
been revealed by the investigation and which have not therefore been taken into account in
the Document. Accordingly, additional studies and actions may be required.

In addition, it is recognised that the passage of time affects the information and assessment provided
in this Document. Core’s opinions are based upon information that existed at the time of the
production of the Document. It is understood that the Services provided allowed Core to form no
more than an opinion of the actual conditions of the site at the time the site was visited and cannot
be used to assess the effect of any subsequent changes in the quality of the site, or its surroundings,
or any laws or regulations.

Any assessments made in this Document are based on the conditions indicated from published
sources and the investigation described. No warranty is included, either express or implied, that
the actual conditions will conform exactly to the assessments contained in this Document.

Where data supplied by the client or other external sources, including previous site investigation
data, have been used, it has been assumed that the information is correct unless otherwise stated.
No responsibility is accepted by Core for incomplete or inaccurate data supplied by others.

Core may have retained subconsultants affiliated with Core to provide Services for the benefit of
Core. To the maximum extent allowed by law, the Client acknowledges and agrees it will not have
any direct legal recourse to, and waives any claim, demand, or cause of action against, Core’s
affiliated companies, and their employees, officers and directors.

This Document is provided for sole use by the Client and is confidential to it and its professional
advisers. No responsibility whatsoever for the contents of this Document will be accepted to any
person other than the Client. Any use which a third party makes of this Document, or any reliance
on or decisions to be made based on it, is the responsibility of such third parties. Core accepts no
responsibility for damages, if any, suffered by any third party as a result of decisions made or
actions based on this Document.




Limitations                                Page 1 of 1                                   Date: 12/07/2018
FRM-065                             Uncontrolled When Printed                                  Issue: 1.02

Page 38

CLIENTCHOICE Awards CLIENTCHOICE Awards

2022 2022
e e

G

BEST CONSULTING.
ENGINEERING FIRM

 

Used in these records

About this file

File size
9.3 MB (large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

Attachment G_Geotechnical_Report.pdf · 9.3 MB (large file)

The download may take up to a minute.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.