Compiled Approved Plans - 51983.3225.21 [As Published]

                      GENERAL SPECIFICATION                                                                                                                                   Construction Notes
                                                                                                                                    Timber Frame: Framing to be built in accordance with AS 1684 Termite protected timbers shall be used on all framing
            ALL BUILDING WORK TO BE CARRIED OUT TO THE BUILDING CODE OF AUSTRALIA & THE BUILDING ACT 1975.                          Approved type flashing & sarking to be attached between cladding & frame along with slab & frame to prevent moisture getting to the frames
            BUILDER TO SUPPLY FOOTPATH PROTECTION & REQUIRED SIGNS TO COMPLY TO WORKPLACE HEALTH & SAFETY ACT.
            PRINCIPLE CONTRACTOR TO HAVE A SITE SPECIFIC WORKPLACE HEALTH & SAFETY MANAGEMENT PLAN TO COMPLY WITH                   All wet areas to be made waterproof or resistant to comply to AS 3740 & BCA 3.8.1
            GOVERNMENT REGULATIONS TO BE KEPT ONSITE & GIVEN TO ALL CONTRACTORS                                                     Linings used shall be approved for use in wet areas & shall be fixed in strict accordance
            WRITTEN DIMENSIONS TO TAKE PRECEDENCE OVER SCALE.                                                                       with Manufactures specifications. Wet Areas include Laundry & Bathroom
            BUILDER TO VERIFY ALL SET-OUT DIMENSIONS PRIOR TO PLACEMENT OF CONCRETE
            BUILDING MUST COMPLY WITH THE NATIONAL CONSTRUCTION CODES (BCA) & THE QUEENSLAND HOME BUILDING CODE                     All walls to be checked to ensure they are fixed correctly, straight & plumb prior to fixing plasterboard or interior lining
            ALL CONCRETE SLABS & FOOTINGS TO COMPLY WITH (AS 2870)                                                                  Plasterboard or interior linings to be fixed to dry frames in strict compliance with manufactures details. Setting of plasterboard to be done in strict
            ALL STRUCTURAL TIMBERS TO COMPLY WITH NATIONAL TIMBER FRAMING CODES (AS1684.2 &AS1720) & CONSTRUCTION TIMBERS           compliance with manufactures specifications, Sanded to provide a flat smooth finish
            IN QUEENSLAND (CTIQ)
            TERMITE PROTECTION TO (AS3660.1) CERTIFICATES TO BE SUPPLIED & GIVEN TO CERTIFIER                                       Painting: Paints & application to comply to AS 2311 Min 3 coat application system to be used
            ALL WET AREAS TO BE WATERPROOFED, INTERNAL WATERPROOFING TO COMPLY TO (AS 3740) AS IN BCA 3.8.1                         Substrate to be clean & dry correct type sealers & primers to be used for substrate
            ALL GLASS TO COMPLY TO (AS 1288) WINDOWS & DOORS ALONG WITH SCREENING OR SECURITY SCREENS TO COMPLY TO                  If paint is sprayed on then a back roll should be done between coats & after final coat
            RELEVANT REGULATIONS                                                                                                    Mould resistant paint to be used in Bathrooms, Ceilings to have approved ceiling paint applied & be a matt finish
            PLASTERBOARD TO (AS 2589), PAINTING TO COMPLY TO (AS 2311) TILING TO COMPLY TO (AS 3958)
            STAIRS TO COMPLY TO BCA 3.9.1 BALUSTRADE TO COMPLY TO BCA 3.9.2,                                                        Concrete slabs & footings to be poured AS per Plans & in accord with AS 2870
            WIND CLASSIFICATION (N3).                                                                                               Slabs shall be finished to suit floor coverings
                                                                                                                    -
                                                                                                      NOOSA COUNCIL                 All external windows & doors to have appropriate flashing & seals fitted to prevent water getting into building or
                                                                                                     APPROVED PLANS                 to the frame work
                                                                                                51983.3225.07 29 MARCH 2017




      Client: M & K Himgston           Unit 20/30 Hasting St. The Hastings Noosa Heads                 Wind Classification N3                                                                             Mobile: 0407 693 018                                Date     23/03/2017 3:20:18 PM
                                                                                                                                ACCOLADE Building Designs                                                                                                    Drawn by: S.Horn Drawn for A3 Sheet
      RPD: Lot 20 on GTP 1154            Parish: Weyba       County: March       Site Area : 106 m²                                  Proprietor: Steven Horn                                   Email: [email protected] Project Number
                                                                                                                                                                                                                                                                                              1016HMK
     Proposed
Document            Partial Enclosure of Ground Level Under Existing Unit
         Set ID: 23058716                                                                                                               QBSA Lic. 54806                                        Issue Date            23 - March - 2017                            Sheet No. 1          of      6
Version: 4, Version Date: 01/11/2024