Skip to the record
The definitive source for everything Noosa Council.

Council archive · source document

Geotechnical Investigation · MCU24/0153

of 40

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

        Proposed Unit Development
                    51 Elanda Street, Sunshine Beach

Proposed Unit Development 30 September 2024 | Ref. 24265-001-Rev0
30 September 2024 | 24265-001-Rev0                                  i
Full text of the other 39 pages

Page 2

Document Review
 Doc No.      Revision     Prepared By          Reviewed By                 Date Issued
 001          0            Ben Cole             Geoff Hurley                30 September 2024




 Doc No.      Revision     Method of Delivery   Issued To
 001          0            Electronic           Martin Smith ([email protected])




Prepared By                                       Reviewed By




Ben Cole                                          Geoff Hurley BSc (Hons) MSc DIC C.Geol RPEQ 5716
Undergraduate Geotechnical Engineer               Senior Consultant




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                   ii

Page 3

Executive Summary
This report details the results of a geotechnical investigation undertaken for a proposed unit
development at 51 Elanda Street, Sunshine Beach. The investigation comprised drilling of boreholes at
four locations across accessible areas of the development footprint. This report summarises the results
of the investigation and provides geotechnical recommendations regarding earthworks and footings,
together with temporary and permanent basement retention.
Architectural design drawings provided indicate that the development will comprise a three-storey
building, over a single level basement carpark. Excavations will be in the order of up to 7 m deep and
localised filling less than 1 m high is anticipated. Excavations are expected to extend close to the site
boundaries and therefore, some form of temporary retention will be required.
The subsurface conditions encountered in the boreholes are summarised as follows:
▪   Topsoil – comprising loose silty sand to depths of 0.1 m to 0.2 m below ground level (BGL); then
▪   Fill – comprising loose silty sand to depths of between 0.4 m and 1.3 m BGL; then
▪   Natural Sands – comprising poorly graded sands mostly being loose to depths of between 1.4 m
    and 2.6 m BGL; then becoming medium dense and increasing to dense below depths of about
    2.8 to 3.8 m BGL.
No signs of groundwater seepage (‘springs’) were observed during our walk-over. Groundwater was not
encountered in the boreholes at the time of investigation.
Provided the recommendations within this report are adhered to, and subject to detailed design and
construction of the footing and retention system by a suitably qualified and experienced RPEQ structural
engineer, there should be a Low Risk to property from slope instability.
Excavations through the existing soils should be achievable using conventional earthmoving plant (e.g.
small or larger excavators with toothed buckets). Temporary unsurcharged cuts could be formed at
1V:2H in the very loose to loose sands, and at 1V:1H in medium dense (or denser) sand, for batters up to
3 m in height, provided groundwater seepage is not encountered and sands do not slough from the
batter face as they dry out. It is expected that space restrictions will limit battering of temporary cuts on
the site and so some form of temporary retention system, such as sheet piles or contiguous reinforced
concrete piles, will be required. These retention systems, which may have to be temporarily braced during
construction, may also be designed to form the permanent basement walls.
Footings for the proposed development and any ancillary structures (e.g. retaining walls) must penetrate
through any fill materials and unsuitable natural soils (i.e. very loose to loose sands) to found at least
0.5 m into medium dense (or denser) natural sands. Such materials were encountered in the boreholes
below depths of between about 1.4 m and 2.6 m BGL (existing ground levels). High-level footings would
be suitable in excavation areas where medium dense (or denser) natural sands are exposed at the
subgrade level. Piled footings would be required unless excavations expose such materials at or near
foundation subgrade level. Given the sandy soil profile, where deepened footings are required, steel
screw piles are considered to be a suitable foundation type. Due to the presence of loose sands,
together with the close proximity of adjacent buildings, open bored piers or driven piles are not
considered to be suitable for this site. Cast in place continuous flight auger (CFA) piles may also be
suitable for both foundation and shoring piles provided a small rig capable of traversing the site can be
sourced.




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                          iii

Page 4

Contents
Executive Summary.........................................................................................................................................................iii
1.       Introduction ............................................................................................................................................................ 1
2.       Proposed Development ....................................................................................................................................... 1
3.       Method of Investigation ......................................................................................................................................2
4.       Results of Investigation .......................................................................................................................................2
         4.1 Site Description ......................................................................................................................................................... 2
         4.2 Topography................................................................................................................................................................. 4
         4.3 Geology ........................................................................................................................................................................ 5
         4.4 Subsurface Conditions ............................................................................................................................................ 6
         4.5 Groundwater............................................................................................................................................................... 7
         4.6 Surface Drainage....................................................................................................................................................... 7
5.       Slope Stability Assessment .................................................................................................................................8
         5.1 Existing Conditions................................................................................................................................................... 8
         5.2 Stability Assessment ................................................................................................................................................ 9
6.       Geotechnical Recommendations ..................................................................................................................... 11
         6.1 Development Limitations..................................................................................................................................... 11
         6.2 Earthworks ................................................................................................................................................................. 11
              6.2.1   Site Preparation and Trafficability................................................................................................... 11
              6.2.2   Excavations .............................................................................................................................................. 12
              6.2.3   Filling ......................................................................................................................................................... 12
         6.3 Building Foundations ............................................................................................................................................ 13
              6.3.1   Indicative Site Classification .............................................................................................................. 13
              6.3.2   Footing Design....................................................................................................................................... 13
         6.4 Temporary and Permanent Retention ............................................................................................................ 15
         6.5 Drainage ..................................................................................................................................................................... 16
7.       Conclusion ............................................................................................................................................................. 17
8.       limitations .............................................................................................................................................................. 17




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                                                                                                         iv

Page 5

Appendices
Appendix A                    Borehole Reports and Explanatory Notes
Appendix B                    AGS Guidlines - Qualitative Terminology for Use in Assesing the Risk to Property Some
                              Guidelines for Hillside Construction
Appendix C                    Limitations


Text Figures
Text Figure 1: South elevation plan (courtesy Archend).................................................................................................... 1
Text Figure 2: 2023 aerial image of the site and immediate surrounds (courtesy Nearmap imagery) ........... 3
Text Figure 3: Easterly facing view of the site driveway and adjacent alleyway from Elanda Street ................ 3
Text Figure 4: Concrete block retaining wall (LHS) and beam cracking (RHS) at north of site ........................... 4
Text Figure 5: Concrete block wall supporting internal basement undercroft (LHS) and cracking
      observed in retaining wall (RHS) along southern boundary ................................................................................ 4
Text Figure 6: Plan showing ground surface contours (courtesy Noosa Council ‘Intramaps’) ........................... 5
Text Figure 7: Extract of 1:100,000 Laguna Bay Surface Geology Map ........................................................................ 5
Text Figure 8: Extract from NC landslide hazard overlay mapping ............................................................................... 8
Text Figure 9: Footing depth required to prevent undermining ................................................................................. 15



Figures
Figure 1: Site Plan



Tables
Table 1: Summary of Subsurface Conditions........................................................................................................................ 6
Table 2: Stability Risk Levels ........................................................................................................................................................ 9
Table 3: Details of Qualitative Risk Assessment for Property (AGS 2007) ............................................................... 10
Table 4: Retaining Structure Design Parameters............................................................................................................... 16




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                                                                                                    v

Page 6

1.          Introduction
This report details the results of a geotechnical investigation undertaken for a proposed unit
development at 51 Elanda Street, Sunshine Beach. The investigation was performed by Tectonic for
Archend, generally in accordance with Proposal P24478-Rev0, dated 9 August 2024.
The investigation comprised drilling of boreholes at four locations across accessible areas of the
development footprint. This report summarises the results of the investigation and provides
geotechnical recommendations regarding earthworks and footings, together with advice for temporary
and permanent basement retention.
In summary, subject to the implementation of the recommendations made herein, it is assessed that
there would be a Low Risk of slope instability affecting the proposed development in accordance with
the Australian Geomechanics Society Guidelines for Landslide Risk Management, dated March 2007 (AGS
2007).



2.          Proposed Development
Design details provided to us indicate that the development will comprise a three-storey building, over a
basement carpark covering most of the site. The construction will include a combination of masonry
walls and reinforced concrete floors with various architectural finishes to the walls. Excavations for the
development will be in the order of up to 7 m deep in the upslope area adjacent to Elanda Street with
the basement level shallowing to about 2 m to 3 m deep downslope to the east. Localised filling less
than 1 m high is anticipated. Excavations are expected to extend close to the site boundaries and
therefore, some form of temporary retention will be required. Isolated deeper excavations may be
required for the lift overrun pit and other elements.
Extract from the design drawings provided by Archend are provided below in Text Figure 1.




                           Text Figure 1: South elevation plan (courtesy Archend)


Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                       1

Page 7

3.          Method of Investigation
As part of our assessment, a desk-top study was carried out comprising a review of published geological
maps, slope stability studies as well as Noosa Council (NC) planning overlays and site information.
An experienced geotechnical engineer from Tectonic undertook a site walk-over on 6 September 2024 to
visually assess any indicators of past slope instability. The walk-over included assessment of soil
exposures, surface drainage conditions, topography, evidence of erosion or past instability, and
vegetation coverage/condition.
This was followed by a subsurface investigation comprising the drilling of four boreholes (designated
BH1 to BH4) in accessible areas across the site. Borehole BH1 was drilled on the existing driveway
toward the western boundary of the site using Tectonic’s 4WD mounted solid flight auger rig to a depth
of 8 m below ground level (BGL). Due to access restrictions boreholes BH2 to BH4 were drilled using
hand augering techniques to 3 m BGL to the north, east and south of the site. A further two boreholes,
designated BH2A and BH2B were drilled to a depth of 1 m BGL to attempt to delineate rubbish
encountered in the area during a previous soil test by another firm.
In-situ testing, using the dynamic cone penetrometer (DCP) method, was carried out from the ground
surface and within each borehole. DCP testing was extended below the base of the hand augered
boreholes to depths between 4.5 m and 6.0 m BGL. Boreholes were backfilled on completion with
drilling spoil, with excess material slightly mounded at surface.
Laboratory classification testing was not warranted due to the sandy nature of the subsurface conditions
encountered.
Borehole locations are shown in Figure 1 attached at the end of this report, with borehole and DCP logs
presented in Appendix A, together with explanatory notes. Subsurface conditions are discussed in
Section 4.4. Borehole coordinates were recorded using a handheld global positioning system (GPS).
The results of the desk-top study and walk-over survey are included in Section 4 below.



4.          Results of Investigation
4.1         Site Description
The site is formally described as Lot 403 RP48112, covering an area of 755 m2, with frontage to Elanda
Street to the west. At the time of the investigation a two-storey residential building occupied most of
the western part of the site. The building was surrounded by at-grade concrete pathways and slabs with
some garden spaces. Neighbouring properties consisted of two to three storey residential unit buildings
to the north, east and south. An alleyway and drainage easement along the southern boundary provided
pedestrian access between Elanda Street and Henderson Street to the east and also accommodated
hydraulic services including stormwater and sewer mains.
Inferred cut and fill earthworks had taken place across the site and adjacent areas. The site had been
levelled with cut to fill earthworks up to about 2 m high supported by retaining walls along the northern
and southern boundaries. Cut to fill estimated to be up to about 1 m was observed to form retained
garden terraces.



Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                        2

Page 8

Cut and fill embankments were retained by the existing building as well as concrete block retaining walls
ranging in heights of less than 0.5 m to 2.1 m high. Cracking was observed in some retaining walls on the
property, appearing to likely be related to age and poor construction. A rendered concrete block
retaining wall was observed on the northern neighbouring property, increasing up to 2.2 m to form the
entrance of a basement carpark below that building. Other observable walls of neighbouring properties
appeared to be in relatively good structural condition, based on an external assessment.
Significant cracking was observed on a concrete beam at the north-eastern corner of the residence.
Minor cracking was observed in the concrete slab surrounding the building which appeared to be related
to age, poor construction and possibly consolidation of the upper loose sands.
A 2021 aerial image of the site and surrounds is shown in Text Figure 2 overleaf.




                                                                             Subject Site




  Text Figure 2: 2023 aerial image of the site and immediate surrounds (courtesy Nearmap imagery)

Site conditions at the time of our investigation are shown below and overleaf in Text Figures 3 to 5.




                                                                                                3°


   Text Figure 3: Easterly facing view of the site driveway and adjacent alleyway from Elanda Street



Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                      3

Page 9

                                                                                        Cracking in beam




      Text Figure 4: Concrete block retaining wall (LHS) and beam cracking (RHS) at north of site




                                                          Cracking in retaining wall


                                     2.1 m




    Text Figure 5: Concrete block wall supporting internal basement undercroft (LHS) and cracking
                      observed in retaining wall (RHS) along southern boundary




4.2         Topography
As illustrated in Text Figure 6 overleaf, the site is located on the easterly facing flank of an ancient sand
dune which crests about 120 m to the north-west. During the site walk-over, topographic features
specific to the site were noted, and ground slopes were recorded using a hand-held clinometer.
The natural surface profile had been interrupted by historic landscaping and residential construction;
with inferred less altered ground slopes along the alleyway bordering the southern site boundary from
Elanda Street to Henderson Street. Much of the eastern part of the site appeared to be uninterrupted by
historic landscaping. The inferred natural slopes in the area measured at the time of our assessment
ranged from about 3° to the west, up to about 15° to the east. Based on our observations it appeared
that cut and fill earthworks had been undertaken across the site, resulting in a generally flat building
platform and a terraced lawn and garden areas supported by various retaining walls, as discussed in
above in Section 4.1.



Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                              4

Page 10

Generally, no irregular surface features were noted which would indicate global slope instability.




                                                                                       Subject Site




          Text Figure 6: Plan showing ground surface contours (courtesy Noosa Council ‘Intramaps’)


4.3              Geology
Available geological information1 indicates that the site is underlain by Pleistocene age parabolic sand
dunes comprising “quartz sand” (Ref: Text Figure 7).




                 Approx. Site Location




                         Text Figure 7: Extract of 1:100,000 Laguna Bay Surface Geology Map




1
    Queensland Government, Department of Mines and Energy, 1:100,000 Laguna Bay Surface Geology Map, Sheet 9545, 11 July 2018


Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                                              5

Page 11

4.4            Subsurface Conditions
Detailed descriptions of the subsurface conditions encountered in the boreholes are provided in the
borehole reports attached in Appendix A, along with definition sheets which describe terms and
abbreviations used on the reports. The subsurface conditions encountered in the boreholes are
summarised as follows:
▪     Topsoil – comprising loose silty sand to depths of 0.1 m to 0.2 m below ground level (BGL); then
▪     Fill – comprising loose silty sand to depths of between 0.4 m and 0.1.3 m BGL; then
▪     Natural Sands – comprising poorly graded sands mostly being loose to depths of between 1.4 m
      and 2.6 m BGL; then becoming medium dense and increasing to dense below depths of about
      2.8 to 3.8 m BGL.
Table 1 below summarises the subsurface profile in each borehole.

Table 1: Summary of Subsurface Conditions

                                                                                       Medium         Dense (or
    Borehole No.      Topsoil              Fill                 Loose Sands
                                                                                       Dense Sands    denser) Sands
                      0.0 – 0.2            0.2 – 0.4            0.4 – 1.5              1.5 – 2.8      2.8 – 8.0TD
    BH1


                      0.0 – 0.1            0.1 – 0.4            0.4 – 1.4              1.4 – 3.0TD    3.3* – 4.7DCP
    BH2


                      0.0 – 0.1            0.1 – 1.3            1.3 – 2.6              2.6 – 3.0 TD   3.7* – 4.8DCP
    BH3


    BH4               0.0 – 0.1            -                    0.1 – 1.7              1.7 – 3.0TD    3.8 – 4.8TD
Notes: 1.          Depths noted in m BGL at time of investigation (22 February 2022)

2.        NE denotes not encountered

3.        TD denotes borehole terminated at target depth


4.        * inferred from DCP testing

5.        DCP denotes DCP termination depth




A site classification ‘soil test’ report by Australian Soil Investigations (ASI) (Ref. Report No. 230154(S),
dated 12 June 2023) comprised the drilling of two boreholes (designated BH1 and BH2) in accessible
locations to the east of the property. Rubbish was noted by ASI in BH2 at a depth of 0.7 m BGL. Three
boreholes (designated BH2, BH2A and BH2B) were drilled by Tectonic in this area to delineate the extent
of this rubbish, however, no deleterious material was encountered at those locations.
ASI has classified the site as Class P, as per AS2870, due to poor bearing capacity and fill; however, has
stated that the site would have the shrink-swell characteristics of a Class S site.




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                                    6

Page 12

4.5         Groundwater
No signs of groundwater seepage (‘springs’) were observed during our walk-over. Groundwater was not
encountered in the boreholes at the time of investigation.
Groundwater conditions are expected to be reflective of prevailing weather conditions and seepage may
develop particularly following periods of prolonged or heavy rainfall.


4.6         Surface Drainage
Surface drainage would be expected to follow natural surface contours to the east, draining into
stormwater infrastructure at the east of the property and towards the Henderson Street roadside
drainage system. It is noted that the site has a relatively large catchment; however, most runoff from
upslope of the property is anticipated to be intercepted by the existing stormwater infrastructure
associated with the neighbouring structures and roadside drainage systems along Elanda Street.
Given the sandy nature of the site, rainfall would normally be anticipated to infiltrate the ground surface.
However, as the proposed development will occupy a large part of the block, significant run-off from
hard surfaces will occur. Nevertheless, where directed into swales rather than pipes, such run-off would
be expected to infiltrate into the natural sands relatively rapidly.
No significant surface run-off features were noted during our assessment (e.g. deep rilling or scour/wash
out scars). This indicates that significant overland flow is generally absent during rainfall events.
Recommendations to improve surface drainage as part of the development works are provided in
Section 6.5.




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                         7

Page 13

5.          Slope Stability Assessment
5.1         Existing Conditions
The Noosa Planning Scheme 2020 includes a landslide hazard overlay map (Ref. extract in Text Figure 8).
Mapping indicates that part of the site is within a Moderate (pale yellow shading) Landslide Hazard Area.




                                                        Lot boundary




                     Text Figure 8: Extract from NC landslide hazard overlay mapping

It should be noted that the Noosa landslide hazard map is a broad-scale indication of the potential
landslide susceptibility and is superseded by this site-specific assessment. Our observations of surface
features relevant to this slope stability assessment are summarised as follows:
The existing residence and some retaining walls were noted to be cracked in some places however this
distress was inferred to be associated with poor construction or consolidation of upper loose sands as
opposed to global instability.
No indicators of recent global slope instability were observed, i.e. no landslide scarps or ‘hummocky’
ground was evident across the proposed building area.
No signs of groundwater seepage ‘springs’ were observed across the proposed development area.
Overall inferred natural ground slopes were relatively moderate.




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                         8

Page 14

5.2           Stability Assessment
The risk assessment for this project has been carried out following AGS 2007 Practice Note Guidelines for
Landslide Risk Management. Relative levels of risk and their implications are given in Table 2 and the
Qualitative Terminology for Use in Assessing Risk to Property is also attached in Appendix B.

Table 2: Stability Risk Levels

 Risk Level             Example Implications(1)
 V      Very High       Unacceptable without treatment. Extensive detailed investigation and research,
 H      Risk            planning and implementation of treatment options essential to reduce risk to Low;
                        may be too expensive and not practical. Work likely to cost more than value of
                        property.
 H      High Risk       Unacceptable without treatment. Detailed investigation, planning and
                        implementation of treatment options required to reduce risk to Low. Work would
                        cost a substantial sum in relation to the value of the property.
 M      Moderate        May be tolerated in certain circumstances (subject to regulators’ approval) but
        Risk            requires investigation, planning and implementation of treatment options to reduce
                        risk to Low. Treatment options to reduce to Low risk should be implemented as soon
                        as practicable.
 L      Low Risk        Usually acceptable to regulators. Where treatment has been required to reduce the
                        risk to this level, ongoing maintenance required.
 VL     Very Low        Acceptable. Manage by normal slope maintenance procedures.
        Risk


Note: (1) The implications for a particular situation are to be determined by all parties to the risk assessment and may depend
on the nature of the property at risk; these are only given as a general guide.

Given the geology, topography and particularly the relatively moderately sloping terrain across the
proposed development area, it is considered rare that a landslide could affect the proposed development.
Sand dune slopes are generally close to the ‘limit of equilibrium’ where the surface gradient is about 30°,
although possibly lower in the order of 26˚ to 28˚ for very loose sands. The limit of equilibrium is the
‘tipping point’ to instability, where the factor of safety (FOS) of the slope is approximately 1.0. The FOS of
a slope is the balance (ratio) between the forces driving instability (e.g. soil weight, groundwater pressure)
and the resisting forces (e.g. soil friction and cohesion). Inferred natural slopes around this site are
between 3° and 15°.
Considering the existing site conditions (Ref. Section 2), and subject to the implementation of
recommendations given below, it is assessed that there would be a Low (L) Risk of global slope instability
affecting the proposed development. Regulators (NC) normally require that a Very Low or Low Risk of
landslide affecting the property must be demonstrated to enable development approval. Summarised in
Table 3 overleaf is our qualitative assessment of landslide risk for the development site. A summary of
qualitative terminology for use in assessing risk to property is attached (taken from AGS 2007).




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                                                9

Page 15

Table 3: Details of Qualitative Risk Assessment for Property (AGS 2007)
                                                             Assessed
 Hazard                           Likelihood   Consequence
                                                             Risk
                                                                        Comments
 Failure through very loose to    Unlikely     Medium        Low        Given the low to moderate natural gradients through the
 loose natural sands above the                                          proposed building area, it is considered Unlikely that a
 foundation depth                                                       landslip would develop in these materials, subject to
                                                                        implementation of the recommendations in Section 4.
                                                                        Given a potential Medium impact from such instability
                                                                        the resultant risk would be Low as per AGS 2007.

 Deep failure through the         Rare         Major         Low        The likelihood of a deep failure through the medium
 medium dense (or denser)                                               dense (or denser) natural sand below the proposed
 sands below the foundation                                             foundation depth is assessed as Rare due to the lack of
 depth                                                                  precedence of such movements locally, no signs of any
                                                                        existing slope instability and a lack of groundwater.
                                                                        Although the consequence of such a failure would be
                                                                        Major, the resultant risk is Low as per AGS 2007.

 Temporary instability through    Rare         Major         Low        The likelihood of a slip/failure through any temporary
 temporary retention system, as                                         retention system (sheet pile wall, contiguous pile wall or
 discussed in Section 6.4.                                              similar) as outlined in Section 6.4, is assessed as Rare,
                                                                        subject to detailed design by a suitable qualified RPEQ
                                                                        engineer and construction by a specialist contractor
                                                                        which accounts for the required factors of safety against
                                                                        slope instability. Although the consequence of such a
                                                                        failure would be Major, the resultant risk is Low as per
                                                                        AGS2007.



The potential impacts on slope stability of the development components have been assessed, and the
measures recommended below in Section 4 have been designed to mitigate those impacts.




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                                                   10

Page 16

6.          Geotechnical Recommendations
General recommendations to help maintain the stability of the site are given in the document Some
Guidelines for Hillside Construction, which is attached.


6.1         Development Limitations
It is anticipated earthworks may include cuts for the basement level of up to about 7 m deep with only
minor filling expected to be required up to about 1 m in height to form finished surface levels. Should
proposed cuts/fills exceed this quantity, Tectonic must assess the impacts on slope stability before
construction.


6.2         Earthworks
6.2.1       Site Preparation and Trafficability
Following removal of the existing buildings and associated construction elements (e.g. footings, services,
etc.), any tree stumps and large roots should be ‘grubbed out’. Any organic rich topsoil and uncontrolled
fill should then be stripped and set aside. Based on site observations and boreholes, topsoil (where
present) stripping depths should generally range between 0.1 m and 0.2 m BGL, with uncontrolled fill
encountered to depths of between 0.4 m to 0.6 m BGL. It is noted that deeper pockets of topsoil or
uncontrolled fill may exist and deeper, localised grubbing out of tree roots may be required.
Rubbish was noted during soil testing by ASI at a depth of 0.7 m BGL. Three boreholes (designated BH2,
BH2A and BH2B) were drilled by Tectonic in this area to delineate the extent of this rubbish, however, no
deleterious material was encountered at those locations. It would be prudent to allow to investigate this
area further by excavation of test pits prior to construction commencing to assess if rubbish is present
and to what extent.
Topsoil materials must not be used in structural fill; however, may be placed across landscaping areas.
Unsuitable natural material such as any saturated, loose or soft materials encountered should also be
removed during subgrade preparation for bulk earthworks.
It should be noted that compaction of such relatively ‘clean’ sands as structural fill requires the addition
of substantial volumes of water (‘flooding’) combined with the use of vibratory compaction equipment
(typically a vibrating plate). Care must be taken with the use of vibratory equipment (e.g. compactors or
sheet piling) to ensure that there are no adverse impacts on surrounding structures. The impacts from
ground vibration must be closely monitored and managed during construction. It would be prudent to
conduct a dilapidation survey of neighbouring structures prior to commencement of construction.
The exposed natural subgrade following excavations will likely be in a loose condition and must be
compacted by several passes of a vibrating plate or minimum 4 tonne vibrating smooth drum roller, in
conjunction with surface application of ample water, to achieve the required compaction.
Due to the potential for poor trafficability during placement of a minimum 150 mm thick granular
working platform may be required on soil subgrades along haul roads and across laydown areas.
Specific platform design would be required prior to mobilisation and trafficking of any heavy mobile
plant on the site (e.g. cranes, concrete pumps or piling rigs).




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                         11

Page 17

Construction areas and surrounds should be graded to shed surface water runoff. Swale drains should
be constructed along the crest and toe of any cuts, and above fill batters, where possible. Drains are to
be graded to discharge collected waters to a control point(s) before release into existing stormwater
infrastructure.
It should be noted that during wet weather, the natural soils may cause sediment run-off. Appropriate
erosion and sediment control measures must be installed prior to commencement of earthworks at this
site.

6.2.2       Excavations
Excavations through the existing soils should be achievable using conventional earthmoving plant (e.g.
small or larger excavators with toothed buckets). Temporary, unsurcharged cuts in the very loose to
loose sand could be formed at 1V:2H and at 1V:1H in medium dense (or denser) sand for batters up to
3 m in height. Flatter batters or temporary retention may be required if groundwater seepage is
encountered or if sloughing of dry sand occurs at the batter surface. Deeper cuts, if required, should be
specifically assessed by Tectonic.
If filling or permanent cuts exceed 1 m, then these must be retained. Permanent cut and fill batters up to
1 m high shall not exceed 1V:2.5H. Any permanent soil and fill batters will require erosion protection (e.g.
revegetation or surface protection).
Temporary batter slopes would not be able to be achieved in places, due to spatial restraints, and so
temporary shoring will be required (e.g. sheet piles or contiguous piles) as per the recommendations in
Section 6.4 below. Excavations in close proximity to existing structures, including on neighbouring
properties, will need to be specifically designed to prevent undermining. It is recommended that footing
exposures or confirmation of foundations via certified building plans be undertaken to assess the
possibility of undermining. If undermining is a potential issue the existing structures may need to be
underpinned or excavations may require temporary shoring.
The advice of a suitably qualified and experienced RPEQ structural engineer must be sought regarding
any potential undermining as well as design and construction of any underpins/temporary shoring (if
required).
The above recommendations do not supersede any existing safety regulations or legislation applicable to
excavations (e.g. limits on personnel entry into trenches).
Due to the highly permeable nature of the sands at this site, stormwater is expected to rapidly infiltrate
the ground, making un-sealed surface drainage ineffective for the control of flows. Any sealed areas
should be graded to ensure free drainage of stormwater away from construction areas, and to a control
point(s).

6.2.3       Filling
The existing sandy soils (fill and natural) where free of deleterious materials (e.g. vegetation, building
debris etc.) may be reused as structural fill, subject to appropriate moisture adjustment. It should be
noted that compaction of such relatively ‘clean’ sands as structural fill requires the addition of substantial
volumes of water (‘flooding’) combined with the use of vibratory compaction equipment (typically a
smooth drum roller or heavy vibrating plate).




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                          12

Page 18

Should importation of fill be required, it is recommended that such fill should comply with the following:
▪   Minimum CBR of 10%
▪   Maximum plasticity index of 15%
▪   Shrink-swell index ≤ 1%
▪   Maximum particle size of 100 mm
Any fill should be compacted at moisture contents within the range of ±2% of optimum moisture
content for Standard Compaction. Fill material should be placed in 250 mm thick (loose thickness) layers
and be compacted by repeated rolling using a minimum 4 tonne smooth drum roller (or equivalent, with
vibration on if safe to do so) to achieve a dry density ratio of at least 98% of the maximum Dry Density
Ratio (DDR), based upon the Standard Compaction method, or a Dry Density Index of at least 75%.
Confirmatory compaction testing must be carried out at regular intervals. A minimum of two tests per
vertical lift is recommended where structural fill heights are to exceed 300 mm. Further details for
control and testing of fill are given in Australian Standard AS 3798-2007 Guidelines on Earthworks for
Commercial and Residential Developments.
Fill embankment edges must be over-filled by 0.5 m (horizontally) and then trimmed back to well
compacted material.


6.3         Building Foundations
6.3.1       Indicative Site Classification
Site classifications for footing design are determined in accordance with AS 2870-2011 Residential Slabs
and Footings, and depend on the depth of cut / fill undertaken at a site, variations in the natural soil/rock
depths, and the reactivity of the in situ soil / rock and any imported fill materials. It should be noted that
the proposed works are outside of the scope of AS2870.
Based on the results of the investigation, the site is classified as Class P in accordance with AS 2870-2011
Residential Slabs and Footings, due to the presence of uncontrolled fill and poor bearing capacity soils at
shallow depths. However, if not for these factors, the site would have the characteristics of Class S, with
the estimated characteristic surface movements (‘ys’) ranging up to about 20 mm. Due to the potential
variability in subgrade density a site classification of Class M is recommended in relation to assessment
of flexibility requirements for ground slab, footing and plumbing design.

6.3.2       Footing Design
No design loadings were available at the time of reporting. Footings for the proposed development and
any ancillary structures (e.g. retaining walls, etc.) must penetrate through any fill materials and unsuitable
natural soils (i.e. very loose to loose sands) to found at least 0.5 m into medium dense (or denser) natural
sands. Such materials were encountered below depths between about 1.4 m and 2.6 m BGL (existing
ground levels) in the boreholes. Thus, piled footings will be required unless excavations expose such
materials at or near foundation subgrade level (e.g. as anticipated in deeper basement cut areas).
Piles so founded may be designed using an allowable end bearing pressure of 500 kPa. High level
footings, where achievable in deeper cut areas, may be designed using an allowable bearing pressure of
100 kPa provided that they are founded in the natural medium dense (or denser) sands. Settlement under
such loads is expected to be in the order of up to 20 mm or 1% of footing width.



Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                          13

Page 19

Given the sandy soil profile and depths of footings required, steel screw piles are considered to be a
suitable foundation type for the proposed unit development generally. However, in areas of cut
exposing medium dense (or denser) sands at the subgrade level conventional high-level footings may be
adopted. It should be noted that excavation for concrete strip footings (or similar) may loosen the base.
Therefore, the use of a vibrating plate and ample water would be required to densify any high-level
footing bases prior to the placement of reinforcing steel.
Due to the presence of loose sands, open bored piers or driven piles are not considered to be suitable
for this site. Steel reinforced concrete bore piles may be possible; however, the use of casings or
sacrificial liners (e.g. formatube etc.) would be required. Cast in place continuous flight auger (CFA) piles
may also be suitable for foundation piles (and shoring piles) provided a small rig capable of traversing
the site can be sourced.
The advice of a specialist piling contractor must be sought regarding feasibility, design and installation of
the piling system for this site, including an assessment of potential vibration effects on nearby structures,
and monitoring requirements.
If steel screw piles are adopted, it will be important to ensure close supervision of installation, as piling
may not encounter sufficient drilling resistance (from torque measurement) in sands at the suggested
founding depth, and piles could extend to much greater depth than necessary.
It is therefore recommended that site specific static load testing be conducted from screw piles, if
adopted, at a minimum. Where tension or compression capacity developed in the footings is critical for
the future structure (e.g. resistance to uplift forces from high winds), then cyclic load tests (including
measurement of deflections under tension and compression cycles) should also be undertaken prior to
construction. Kentledge for static testing, or simulated cyclic loads, should prove the piles to a minimum
of two times the expected working load within tolerable deflections.
Footing design should also account for potential soil reactivity to be equivalent to Class M. It should be
noted that placement of reactive clay (which is not recommended) may result in a more severe equivalent
site classification, such as H1 or greater.
All footings should found such that they are not adversely affected by any adjacent excavations, trenches,
retaining walls, or in ground structures that are not designed to support building loads. Footings should
found at least below a plane extending 1 m horizontally from the base of trenches/excavations/retaining
walls/swimming pool, then rising up at 1V:1H, as illustrated in Text Figure 10 overleaf.




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                              14

Page 20

                      Text Figure 9: Footing depth required to prevent undermining

Site drainage should be designed to readily remove surface water and to prevent ponding of water on
subgrade areas during construction and also adjacent to foundations and perimeter slabs once
construction is completed. It is recommended that footings be inspected by a suitably qualified and
experienced engineer prior to placement of steel reinforcement and pouring of concrete to confirm
allowable bearing pressures and cleanliness of excavations.
If any soil conditions encountered during construction are found to differ from those noted in the
geotechnical investigation, Tectonic should be notified immediately and an inspection carried out to
determine if changes to footing design are required.


6.4         Temporary and Permanent Retention
Excavations for the basement level may extend to depths of around 7 m BGL (existing ground levels) and
the basement footprint will extend close to some of the site boundaries, so some form of temporary
shoring will be required to support the basement excavation.
Based upon our experience with similar sites, we anticipate that temporary shoring may be achieved by
use of reinforced concrete contiguous pile wall. Sheet piling is not considered suitable for this site due
to the depth of the excavation, the risk of consolidation of loose sands from vibratory effects and the
potential for lateral movements to result in distress to existing structures or underground services behind
the boundary walls. An alternative a secant pile wall configuration could be considered along with
propping of the shoring wall with the use of internal struts. The temporary wall can also act as the
permanent basement wall if appropriately designed.
Installation of such piles in this setting would require the use of cast in place CFA piles. We understand
that the client has been in consultation with a specialist contractor who has a small specialised rig that
would be capable of installing such piles on this terrain. The advice of a specialist shoring contractor
must be sought regarding feasibility, design and installation of the proposed retention and subsurface
drainage system. It will be necessary to conduct numerical analysis to optimise the retention system.


Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                           15

Page 21

Detailed design will also need to account for relevant factors of safety to maintain the temporary and
long-term stability of the retention system and control deflections so as not to put neighbouring
structures or underground services at risk or distress.
Retaining structures greater than 1 m high, or those required to support surcharge loads or sloping
backfill, will require engineer design and certification of construction. Retaining wall design should be
carried out in accordance with AS4678-2002 Earth retaining structures.
Design for temporary and permanent retaining structures could be carried out using a trapezoidal (for
propped or anchored walls) pressure distribution applicable to the wall type and based on the
parameters listed in Table 4. These values do not include allowance for hydrostatic pressures nor
transient (e.g. construction) or adjacent footing loadings.

Table 4: Retaining Structure Design Parameters

                               Unit                          Lateral earth pressure coefficients
                                              Friction
 Retained material             weight                        Ka                   Ko                    Kp
                                              angle (°)
                               (kN/m3)                       (Cantilever wall)    (Non-yielding wall)
                               18             28             0.36                 0.53                  2.77
 Very Loose/ Loose
 Sands


                               19             34             0.28                 0.44                  3.54
 Medium Dense (or
 Denser) Sands


                               *              *              *                    *                     *
 Future Controlled Fill*


Note:   * Depends on fill material type and level of compaction.

Retaining structures must be founded as per the recommendations in Section 6.3.2 above with the piled
footings, if required, also designed to resist lateral loads imposed by the retaining wall. Detailed design
must include an assessment of stability.


6.5          Drainage
Surface diversion drainage should be constructed above the crest of any new cut or fill embankment or
retaining walls (e.g. grassed or landscaped swales or diversion mounds). Adequate site drainage must be
installed to ensure that stormwater runoff is directed away from building walls, footings, batters and
retaining walls.
Although unlikely, if groundwater seepage is encountered during excavations, Tectonic must be notified
to assess the impact on stability.
All excess stormwater collected around the residence (including overflow from rainwater tanks etc.) must
be directed by pipes or lined channels to discharge into the existing stormwater infrastructure along
Bottlebrush Avenue or Noosa Drive. Subsurface disposal of stormwater must not be undertaken.



Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                             16

Page 22

7.          Conclusion
Based on the findings of our assessment it is assessed that there would be a Low Risk of slope instability
affecting the proposed development subject to implementation of the recommendations given in this
report.




8.          Limitations
Your attention is drawn to the document Limitations, which is included in Appendix C of this report. The
statements presented in this document are intended to advise you of what your realistic expectations of
this report should be, and to present you with recommendations on how to minimise the risks associated
with the services provided by Tectonic for this project.




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                       17

Page 23

 

 

0 5 10 15 20m LEGEND

 

 

 

 

 

 

 

 

 

CHEN, DRC IE CT Ae APPROXIMATE BOREHOLE LOCATIONS
ARCHEND GEOTECHNICAL INVESTIGATION FOR PROPOSED UNIT DEVELOPMENT
DRAWN BY DATE 3 51 ELANDA STREET, SUNSHINE BEACH CI SITE BOUNDARY
BC 24/09/2024 " DRAWING TITLE NOTES
CHECKED BY DATE SITE PLAN BASEMAP COURTESY OF NEARMAP, DATED 15 NOVEMBER 2023
DP 24/09/2024
PROJECT NO. DOC NO. FIGURE NO. REVISION
SCALE SHEET SIZE
AS SHOWN AB 24265 001 1 0

 

 

 

 

 

 

 

 

 

Page 24

      Appendix A
      Borehole Reports and Explanatory Notes




Proposed Unit Development
30 September 2024 | 24265-001-Rev0             1

Page 25

                                                                                                                                                                                                                                                                                                                                                                                                                                          Borehole No.

                                                                                                                                                                                                                                                                                                                                                                                                                                                BH1
                                                                                                                                                                                                                                                                                                                                                                                                                                          Page 1 of 1

                                                                                                                                                                                                            Engineering Log - Borehole                                                                                                                                 Project No.:                     24265

                                                                                                                                                                                                                 Client:                                     Archend                                                                                                   Commenced:                       6/9/2024
                                                                                                                                                                                                                 Project Name:                               Proposed Unit Development                                                                                 Completed:                       6/9/2024
                                                                                                                                                                                                                 Hole Location:                              51 Elanda Street, Sunshine Beach                                                                          Logged By:                       BC
                                                                                                                                                                                                                 Hole Position:                              510867.0 m E 7079242.0 m N MGA2020 Zone 56                                                                Checked By:                      DP
                                                                                                                                                                                                                 Drill Model and Mounting:                                    4WD Auger                                                Inclination: -90°               RL Surface:                 No survey
                                                                                                                                                                                                                 Hole Diameter:                                               100 mm                                                   Bearing:     360°               Datum:                      AHD       Operator:               WD

                                                                                                                                                                                                                                    Drilling Information                                                                                              Material Description and Observations




                                                                                                                                                                                                                                                                                                                                                                                Relative Density
                                                                                                                                                                                                                                                                                                         Classification                                                                                                              DCP TEST
                                                                                                                                                                                                                     Penetration




                                                                                                                                                                                                                                                                                                                                                                                                     Pocket




                                                                                                                                                                                                                                                                                                                                                                                Consistency
                                                                                                                                                                                                                                                                                           Graphic Log


                                                                                                                                                                                                                                                        Samples                                                                          Material Description
                                                                                                                                                                                                                                                                                                                                                                                                   Penetrometer




                                                                                                                                                                                                                                                                                                                                                                                Condition
                                                                                                                                                                                                                                                                   Recovery




                                                                                                                                                                                                                                                         Tests                                                             soil type: plasticity or particle characteristics,




                                                                                                                                                                                                                                                                                                                                                                                Moisture
                                                                                                                                                                                                                                                                                                                                                                                                      UCS                         Blows per 100 mm
                                                                                                                                                                                                                                                                                                         Symbol
                                                                                                                                                                                                            Method




                                                                                                                                                                                                                                                                                                                            secondary and minor components, colour
                                                                                                                                                                                                                                   Water




                                                                                                                                                                                                                                                        Remarks                RL Depth                                                                                                               (kPa)
                                                                                                                                                                                                                                                                               (m) (m)                                                                                                                             0       5        10     15     20   25




                                                                                                                                                                                                                                                                                                                                                                                                    100
                                                                                                                                                                                                                                                                                                                                                                                                    200
                                                                                                                                                                                                                                                                                                                                                                                                    300
                                                                                                                                                                                                                                                                                                                                                                                                    400
                                                                                                                                                                                                                                                                                                                                                                                                    500
                                                                                                                                                                                                                                                                                                                          Silty SAND (TOPSOIL), fine to coarse
                                                                                                                                                                                                                                                                                                                          grained, brown, with organics
                                                                                                                                                                                                                                                                                                                          Silty SAND (FILL), fine to coarse grained,
                                                                                                                                                                                                                                                                                                           SP
                                                                                                                                                                                                            HA




                                                                                                                                                                                                                                                                                                                          orange brown, with fine to medium sized
                                                                                                                                                                                                                                                                                                                          subrounded gravel, with clay pockets                             L
                                                                                                                                                                                                                                                                                                                          SAND, fine to medium grained, grey, with silt,                                               Augered to 0.9m
                                                                                                                                                                                                                                                                                     1                                    (AEOLIAN)
                                                                                                                                                                                                                                                                                                                          becoming pale grey, without silt




                                                                                                                                                                                                                                                                                     2
                                                                                                                                                                                                                                                     DS_2.0-2.5m
                                                                                                                                                                                                                                                                                                                                                                                         MD
TECTONIC 3.00.2 LIB.GLB Log 1 TECTONIC BOREHOLE 24265.GPJ <<DrawingFile>> 24/9/2024 13:59 10.02.00.04 Datgel Lab and In Situ Tool - DGD | Lib: Tectonic 3.00.2 2021-03-30 Prj: Tectonic 3.00.2 2021-03-30




                                                                                                                                                                                                                                                                                     3
                                                                                                                                                                                                                                   Not Encountered




                                                                                                                                                                                                                                                                                                                                                                                           D

                                                                                                                                                                                                                                                                                     4                                                                                            M

                                                                                                                                                                                                                                                                                                                                                                                                                       Augered to 4.4m
                                                                                                                                                                                                            AD/T




                                                                                                                                                                                                                                                                                     5




                                                                                                                                                                                                                                                                                                                                                                                                                       Augered to 5.9m
                                                                                                                                                                                                                                                                                     6                                                                                                                                 20/70
                                                                                                                                                                                                                                                                                                                                                                                         VD




                                                                                                                                                                                                                                                                                     7




                                                                                                                                                                                                                                                                                     8
                                                                                                                                                                                                                                                                                                                          Hole Terminated at 8.00 m
                                                                                                                                                                                                                                                                                                                          Target depth

                                                                                                                                                                                                                      Method                                           Penetration                                        Water                   Samples and Tests                        Moisture Condition                  Consistency/Relative Density
                                                                                                                                                                                                                 AD/T-Auger Drilling TC Bit                                     VE - Very Easy        Level (Date)                         U## - Undisturbed Sample (## mm)                    D - Dry                             VS - Very Soft
                                                                                                                                                                                                                 AD/V-Auger Drilling V Bit                                      E - Easy                                                   DS - Disturbed Sample                               M - Moist                           S - Soft
                                                                                                                                                                                                                 RT - Rotary Tri-cone Bit                                                             Inflow                               BDS- Bulk Disturbed Sample                          W - Wet                             F - Firm
                                                                                                                                                                                                                 RD - Rotary Drilling                                           F - Firm                                                   SPT - Standard Penetration Test                                                         VSt - Very Stiff
                                                                                                                                                                                                                                                                                                      Partial Loss
                                                                                                                                                                                                                 NMLC -Rock Core                                                H - Hard                                                                                                                                           H - Hard
                                                                                                                                                                                                                                                                                VH - Very hard       Complete Loss
                                                                                                                                                                                                                 HA - Hand Auger                                                                                                                                                                   Plastic Limit                   VL - Very Loose
                                                                                                                                                                                                                                                                              Graphic Log/Core Loss                                                                                                                                L   - Loose
                                                                                                                                                                                                                                                                                                                                                  Classification Symbols                              < PL                         MD - Medium Dense
                                                                                                                                                                                                                                                                                 Core recovered (hatching                                         and Soil Descriptions                                                            D - Dense
                                                                                                                                                                                                                                                                                 indicates material)                                                                                                  = PL
                                                                                                                                                                                                                                                                                                                                                   Based on Unified Soil                              < PL                         VD - Very Dense
                                                                                                                                                                                                                                                                                 Core loss                                                         Classification System                                                           Fr - Friable

Page 26

                                                                                                                                                                                                                                                                                                                                                                                                                                     Borehole No.

                                                                                                                                                                                                                                                                                                                                                                                                                                           BH2
                                                                                                                                                                                                                                                                                                                                                                                                                                     Page 1 of 1

                                                                                                                                                                                                            Engineering Log - Borehole                                                                                                                             Project No.:                     24265

                                                                                                                                                                                                                 Client:                                 Archend                                                                                                   Commenced:                       6/9/2024
                                                                                                                                                                                                                 Project Name:                           Proposed Unit Development                                                                                 Completed:                       6/9/2024
                                                                                                                                                                                                                 Hole Location:                          51 Elanda Street, Sunshine Beach                                                                          Logged By:                       BC
                                                                                                                                                                                                                 Hole Position:                          510885.0 m E 7079262.0 m N MGA2020 Zone 56                                                                Checked By:                      DP
                                                                                                                                                                                                                 Drill Model and Mounting:                                4WD Auger                                                Inclination: -90°               RL Surface:                 No survey
                                                                                                                                                                                                                 Hole Diameter:                                           100 mm                                                   Bearing:     360°               Datum:                      AHD       Operator:             WD

                                                                                                                                                                                                                                    Drilling Information                                                                                          Material Description and Observations




                                                                                                                                                                                                                                                                                                                                                                            Relative Density
                                                                                                                                                                                                                                                                                                     Classification                                                                                                            DCP TEST
                                                                                                                                                                                                                     Penetration




                                                                                                                                                                                                                                                                                                                                                                                                 Pocket




                                                                                                                                                                                                                                                                                                                                                                            Consistency
                                                                                                                                                                                                                                                                                       Graphic Log


                                                                                                                                                                                                                                                     Samples                                                                         Material Description
                                                                                                                                                                                                                                                                                                                                                                                               Penetrometer




                                                                                                                                                                                                                                                                                                                                                                            Condition
                                                                                                                                                                                                                                                               Recovery




                                                                                                                                                                                                                                                      Tests                                                            soil type: plasticity or particle characteristics,




                                                                                                                                                                                                                                                                                                                                                                            Moisture
                                                                                                                                                                                                                                                                                                                                                                                                  UCS                      Blows per 100 mm
                                                                                                                                                                                                                                                                                                     Symbol
                                                                                                                                                                                                            Method




                                                                                                                                                                                                                                                                                                                        secondary and minor components, colour
                                                                                                                                                                                                                                   Water




                                                                                                                                                                                                                                                     Remarks               RL Depth                                                                                                               (kPa)
                                                                                                                                                                                                                                                                           (m) (m)                                                                                                                             0       5      10      15    20   25




                                                                                                                                                                                                                                                                                                                                                                                                100
                                                                                                                                                                                                                                                                                                                                                                                                200
                                                                                                                                                                                                                                                                                                                                                                                                300
                                                                                                                                                                                                                                                                                                                                                                                                400
                                                                                                                                                                                                                                                                                                                                                                                                500
                                                                                                                                                                                                                                                                                                                      Silty SAND (TOPSOIL), fine to coarse
                                                                                                                                                                                                                                                                                                                      grained, brown, with organics
                                                                                                                                                                                                                                                                                                                      Silty SAND (FILL), fine to coarse grained,
                                                                                                                                                                                                                                                                                                       SP             brown
                                                                                                                                                                                                                                                                                                                      SAND, fine to medium grained, grey,                              L
                                                                                                                                                                                                                                                                                                                      (AEOLIAN)
                                                                                                                                                                                                                                   Not Encountered




                                                                                                                                                                                                                                                                                                                                                                                                                   Augered to 1.0m
                                                                                                                                                                                                                                                                                 1
                                                                                                                                                                                                                                                                                                                      becoming pale grey


                                                                                                                                                                                                                                                                                                                                                                              M
                                                                                                                                                                                                            HA




                                                                                                                                                                                                                                                                                                                                                                                     MD
                                                                                                                                                                                                                                                                                                                                                                                                                   Augered to 2.0m
                                                                                                                                                                                                                                                                                 2




                                                                                                                                                                                                                                                                                                                                                                                       D
TECTONIC 3.00.2 LIB.GLB Log 1 TECTONIC BOREHOLE 24265.GPJ <<DrawingFile>> 24/9/2024 13:59 10.02.00.04 Datgel Lab and In Situ Tool - DGD | Lib: Tectonic 3.00.2 2021-03-30 Prj: Tectonic 3.00.2 2021-03-30




                                                                                                                                                                                                                                                                                 3
                                                                                                                                                                                                                                                                                                                      Hole Terminated at 3.00 m
                                                                                                                                                                                                                                                                                                                      Target depth




                                                                                                                                                                                                                                                                                 4




                                                                                                                                                                                                                                                                                 5




                                                                                                                                                                                                                                                                                 6




                                                                                                                                                                                                                                                                                 7




                                                                                                                                                                                                                                                                                 8



                                                                                                                                                                                                                      Method                                       Penetration                                        Water                   Samples and Tests                        Moisture Condition               Consistency/Relative Density
                                                                                                                                                                                                                 AD/T-Auger Drilling TC Bit                                 VE - Very Easy        Level (Date)                         U## - Undisturbed Sample (## mm)                    D - Dry                          VS - Very Soft
                                                                                                                                                                                                                 AD/V-Auger Drilling V Bit                                  E - Easy                                                   DS - Disturbed Sample                               M - Moist                        S - Soft
                                                                                                                                                                                                                 RT - Rotary Tri-cone Bit                                                         Inflow                               BDS- Bulk Disturbed Sample                          W - Wet                          F - Firm
                                                                                                                                                                                                                 RD - Rotary Drilling                                       F - Firm                                                   SPT - Standard Penetration Test                                                      VSt - Very Stiff
                                                                                                                                                                                                                                                                                                  Partial Loss
                                                                                                                                                                                                                 NMLC -Rock Core                                            H - Hard                                                                                                                                        H - Hard
                                                                                                                                                                                                                                                                            VH - Very hard       Complete Loss
                                                                                                                                                                                                                 HA - Hand Auger                                                                                                                                                               Plastic Limit                VL - Very Loose
                                                                                                                                                                                                                                                                          Graphic Log/Core Loss                                                                                                                             L   - Loose
                                                                                                                                                                                                                                                                                                                                              Classification Symbols                              < PL                      MD - Medium Dense
                                                                                                                                                                                                                                                                             Core recovered (hatching                                         and Soil Descriptions                                                         D - Dense
                                                                                                                                                                                                                                                                             indicates material)                                                                                                  = PL
                                                                                                                                                                                                                                                                                                                                               Based on Unified Soil                              < PL                      VD - Very Dense
                                                                                                                                                                                                                                                                             Core loss                                                         Classification System                                                        Fr - Friable

Page 27

                                                                                                                                                                                                                                                                                                                                                                                                                                    Borehole No.

                                                                                                                                                                                                                                                                                                                                                                                                                                      BH2A
                                                                                                                                                                                                                                                                                                                                                                                                                                    Page 1 of 1

                                                                                                                                                                                                            Engineering Log - Borehole                                                                                                                                   Project No.:                     24265

                                                                                                                                                                                                                 Client:                                       Archend                                                                                                   Commenced:                       6/9/2024
                                                                                                                                                                                                                 Project Name:                                 Proposed Unit Development                                                                                 Completed:                       6/9/2024
                                                                                                                                                                                                                 Hole Location:                                51 Elanda Street, Sunshine Beach                                                                          Logged By:                       BC
                                                                                                                                                                                                                 Hole Position:                                510882.0 m E 7079259.0 m N MGA2020 Zone 56                                                                Checked By:                      DP
                                                                                                                                                                                                                 Drill Model and Mounting:                                      4WD Auger                                                Inclination: -90°               RL Surface:                 No survey
                                                                                                                                                                                                                 Hole Diameter:                                                 100 mm                                                   Bearing:     360°               Datum:                      AHD       Operator:       WD

                                                                                                                                                                                                                                     Drilling Information                                                                                               Material Description and Observations




                                                                                                                                                                                                                                                                                                                                                                                  Relative Density
                                                                                                                                                                                                                                                                                                           Classification
                                                                                                                                                                                                                     Penetration




                                                                                                                                                                                                                                                                                                                                                                                                       Pocket




                                                                                                                                                                                                                                                                                                                                                                                  Consistency
                                                                                                                                                                                                                                                                                             Graphic Log


                                                                                                                                                                                                                                                           Samples                                                                         Material Description
                                                                                                                                                                                                                                                                                                                                                                                                     Penetrometer




                                                                                                                                                                                                                                                                                                                                                                                  Condition
                                                                                                                                                                                                                                                                     Recovery




                                                                                                                                                                                                                                                            Tests                                                            soil type: plasticity or particle characteristics,




                                                                                                                                                                                                                                                                                                                                                                                  Moisture
                                                                                                                                                                                                                                                                                                                                                                                                        UCS
                                                                                                                                                                                                                                                                                                           Symbol
                                                                                                                                                                                                            Method




                                                                                                                                                                                                                                                                                                                              secondary and minor components, colour
                                                                                                                                                                                                                                   Not Encountered Water




                                                                                                                                                                                                                                                           Remarks               RL Depth                                                                                                               (kPa)
                                                                                                                                                                                                                                                                                 (m) (m)                                                                                                                             0   5    10     15     20   25




                                                                                                                                                                                                                                                                                                                                                                                                      100
                                                                                                                                                                                                                                                                                                                                                                                                      200
                                                                                                                                                                                                                                                                                                                                                                                                      300
                                                                                                                                                                                                                                                                                                                                                                                                      400
                                                                                                                                                                                                                                                                                                                                                                                                      500
                                                                                                                                                                                                                                                                                                                            Silty SAND (TOPSOIL), fine to coarse
                                                                                                                                                                                                                                                                                                                            grained, brown, with organics
                                                                                                                                                                                                                                                                                                                            Silty SAND (FILL), fine to coarse grained,
                                                                                                                                                                                                                                                                                                             SP                                                                     M        L
                                                                                                                                                                                                            HA




                                                                                                                                                                                                                                                                                                                            brown
                                                                                                                                                                                                                                                                                                                            SAND, fine to medium grained, grey,
                                                                                                                                                                                                                                                                                                                            (AEOLIAN)
                                                                                                                                                                                                                                                                                       1
                                                                                                                                                                                                                                                                                                                            becoming pale grey
                                                                                                                                                                                                                                                                                                                            Hole Terminated at 1.00 m
                                                                                                                                                                                                                                                                                                                            Target depth



                                                                                                                                                                                                                                                                                       2
TECTONIC 3.00.2 LIB.GLB Log 1 TECTONIC BOREHOLE 24265.GPJ <<DrawingFile>> 24/9/2024 13:59 10.02.00.04 Datgel Lab and In Situ Tool - DGD | Lib: Tectonic 3.00.2 2021-03-30 Prj: Tectonic 3.00.2 2021-03-30




                                                                                                                                                                                                                                                                                       3




                                                                                                                                                                                                                                                                                       4




                                                                                                                                                                                                                                                                                       5




                                                                                                                                                                                                                                                                                       6




                                                                                                                                                                                                                                                                                       7




                                                                                                                                                                                                                                                                                       8



                                                                                                                                                                                                                      Method                                             Penetration                                        Water                   Samples and Tests                        Moisture Condition          Consistency/Relative Density
                                                                                                                                                                                                                 AD/T-Auger Drilling TC Bit                                       VE - Very Easy        Level (Date)                         U## - Undisturbed Sample (## mm)                    D - Dry                     VS - Very Soft
                                                                                                                                                                                                                 AD/V-Auger Drilling V Bit                                        E - Easy                                                   DS - Disturbed Sample                               M - Moist                   S - Soft
                                                                                                                                                                                                                 RT - Rotary Tri-cone Bit                                                               Inflow                               BDS- Bulk Disturbed Sample                          W - Wet                     F - Firm
                                                                                                                                                                                                                 RD - Rotary Drilling                                             F - Firm                                                   SPT - Standard Penetration Test                                                 VSt - Very Stiff
                                                                                                                                                                                                                                                                                                        Partial Loss
                                                                                                                                                                                                                 NMLC -Rock Core                                                  H - Hard                                                                                                                                   H - Hard
                                                                                                                                                                                                                                                                                  VH - Very hard       Complete Loss
                                                                                                                                                                                                                 HA - Hand Auger                                                                                                                                                                     Plastic Limit           VL - Very Loose
                                                                                                                                                                                                                                                                                Graphic Log/Core Loss                                                                                                                        L   - Loose
                                                                                                                                                                                                                                                                                                                                                    Classification Symbols                              < PL                 MD - Medium Dense
                                                                                                                                                                                                                                                                                   Core recovered (hatching                                         and Soil Descriptions                                                    D - Dense
                                                                                                                                                                                                                                                                                   indicates material)                                                                                                  = PL
                                                                                                                                                                                                                                                                                                                                                     Based on Unified Soil                              < PL                 VD - Very Dense
                                                                                                                                                                                                                                                                                   Core loss                                                         Classification System                                                   Fr - Friable

Page 28

                                                                                                                                                                                                                                                                                                                                                                                                                                    Borehole No.

                                                                                                                                                                                                                                                                                                                                                                                                                                      BH2B
                                                                                                                                                                                                                                                                                                                                                                                                                                    Page 1 of 1

                                                                                                                                                                                                            Engineering Log - Borehole                                                                                                                                   Project No.:                     24265

                                                                                                                                                                                                                 Client:                                       Archend                                                                                                   Commenced:                       6/9/2024
                                                                                                                                                                                                                 Project Name:                                 Proposed Unit Development                                                                                 Completed:                       6/9/2024
                                                                                                                                                                                                                 Hole Location:                                51 Elanda Street, Sunshine Beach                                                                          Logged By:                       BC
                                                                                                                                                                                                                 Hole Position:                                510884.0 m E 7079258.0 m N MGA2020 Zone 56                                                                Checked By:                      DP
                                                                                                                                                                                                                 Drill Model and Mounting:                                      4WD Auger                                                Inclination: -90°               RL Surface:                 No survey
                                                                                                                                                                                                                 Hole Diameter:                                                 100 mm                                                   Bearing:     360°               Datum:                      AHD       Operator:       WD

                                                                                                                                                                                                                                     Drilling Information                                                                                               Material Description and Observations




                                                                                                                                                                                                                                                                                                                                                                                  Relative Density
                                                                                                                                                                                                                                                                                                           Classification
                                                                                                                                                                                                                     Penetration




                                                                                                                                                                                                                                                                                                                                                                                                       Pocket




                                                                                                                                                                                                                                                                                                                                                                                  Consistency
                                                                                                                                                                                                                                                                                             Graphic Log


                                                                                                                                                                                                                                                           Samples                                                                         Material Description
                                                                                                                                                                                                                                                                                                                                                                                                     Penetrometer




                                                                                                                                                                                                                                                                                                                                                                                  Condition
                                                                                                                                                                                                                                                                     Recovery




                                                                                                                                                                                                                                                            Tests                                                            soil type: plasticity or particle characteristics,




                                                                                                                                                                                                                                                                                                                                                                                  Moisture
                                                                                                                                                                                                                                                                                                                                                                                                        UCS
                                                                                                                                                                                                                                                                                                           Symbol
                                                                                                                                                                                                            Method




                                                                                                                                                                                                                                                                                                                              secondary and minor components, colour
                                                                                                                                                                                                                                   Not Encountered Water




                                                                                                                                                                                                                                                           Remarks               RL Depth                                                                                                               (kPa)
                                                                                                                                                                                                                                                                                 (m) (m)                                                                                                                             0   5    10     15     20   25




                                                                                                                                                                                                                                                                                                                                                                                                      100
                                                                                                                                                                                                                                                                                                                                                                                                      200
                                                                                                                                                                                                                                                                                                                                                                                                      300
                                                                                                                                                                                                                                                                                                                                                                                                      400
                                                                                                                                                                                                                                                                                                                                                                                                      500
                                                                                                                                                                                                                                                                                                                            Silty SAND (TOPSOIL), fine to coarse
                                                                                                                                                                                                                                                                                                                            grained, brown, with organics
                                                                                                                                                                                                                                                                                                                            Silty SAND (FILL), fine to coarse grained,
                                                                                                                                                                                                                                                                                                             SP                                                                     M        L
                                                                                                                                                                                                            HA




                                                                                                                                                                                                                                                                                                                            brown
                                                                                                                                                                                                                                                                                                                            SAND, fine to medium grained, grey,
                                                                                                                                                                                                                                                                                                                            (AEOLIAN)
                                                                                                                                                                                                                                                                                       1
                                                                                                                                                                                                                                                                                                                            becoming pale grey
                                                                                                                                                                                                                                                                                                                            Hole Terminated at 1.00 m
                                                                                                                                                                                                                                                                                                                            Target depth



                                                                                                                                                                                                                                                                                       2
TECTONIC 3.00.2 LIB.GLB Log 1 TECTONIC BOREHOLE 24265.GPJ <<DrawingFile>> 24/9/2024 13:59 10.02.00.04 Datgel Lab and In Situ Tool - DGD | Lib: Tectonic 3.00.2 2021-03-30 Prj: Tectonic 3.00.2 2021-03-30




                                                                                                                                                                                                                                                                                       3




                                                                                                                                                                                                                                                                                       4




                                                                                                                                                                                                                                                                                       5




                                                                                                                                                                                                                                                                                       6




                                                                                                                                                                                                                                                                                       7




                                                                                                                                                                                                                                                                                       8



                                                                                                                                                                                                                      Method                                             Penetration                                        Water                   Samples and Tests                        Moisture Condition          Consistency/Relative Density
                                                                                                                                                                                                                 AD/T-Auger Drilling TC Bit                                       VE - Very Easy        Level (Date)                         U## - Undisturbed Sample (## mm)                    D - Dry                     VS - Very Soft
                                                                                                                                                                                                                 AD/V-Auger Drilling V Bit                                        E - Easy                                                   DS - Disturbed Sample                               M - Moist                   S - Soft
                                                                                                                                                                                                                 RT - Rotary Tri-cone Bit                                                               Inflow                               BDS- Bulk Disturbed Sample                          W - Wet                     F - Firm
                                                                                                                                                                                                                 RD - Rotary Drilling                                             F - Firm                                                   SPT - Standard Penetration Test                                                 VSt - Very Stiff
                                                                                                                                                                                                                                                                                                        Partial Loss
                                                                                                                                                                                                                 NMLC -Rock Core                                                  H - Hard                                                                                                                                   H - Hard
                                                                                                                                                                                                                                                                                  VH - Very hard       Complete Loss
                                                                                                                                                                                                                 HA - Hand Auger                                                                                                                                                                     Plastic Limit           VL - Very Loose
                                                                                                                                                                                                                                                                                Graphic Log/Core Loss                                                                                                                        L   - Loose
                                                                                                                                                                                                                                                                                                                                                    Classification Symbols                              < PL                 MD - Medium Dense
                                                                                                                                                                                                                                                                                   Core recovered (hatching                                         and Soil Descriptions                                                    D - Dense
                                                                                                                                                                                                                                                                                   indicates material)                                                                                                  = PL
                                                                                                                                                                                                                                                                                                                                                     Based on Unified Soil                              < PL                 VD - Very Dense
                                                                                                                                                                                                                                                                                   Core loss                                                         Classification System                                                   Fr - Friable

Page 29

                                                                                                                                                                                                                                                                                                                                                                                                                                     Borehole No.

                                                                                                                                                                                                                                                                                                                                                                                                                                           BH3
                                                                                                                                                                                                                                                                                                                                                                                                                                     Page 1 of 1

                                                                                                                                                                                                            Engineering Log - Borehole                                                                                                                             Project No.:                     24265

                                                                                                                                                                                                                 Client:                                 Archend                                                                                                   Commenced:                       6/9/2024
                                                                                                                                                                                                                 Project Name:                           Proposed Unit Development                                                                                 Completed:                       6/9/2024
                                                                                                                                                                                                                 Hole Location:                          51 Elanda Street, Sunshine Beach                                                                          Logged By:                       BC
                                                                                                                                                                                                                 Hole Position:                          510899.0 m E 7079247.0 m N MGA2020 Zone 56                                                                Checked By:                      DP
                                                                                                                                                                                                                 Drill Model and Mounting:                                4WD Auger                                                Inclination: -90°               RL Surface:                 No survey
                                                                                                                                                                                                                 Hole Diameter:                                           100 mm                                                   Bearing:     360°               Datum:                      AHD       Operator:             WD

                                                                                                                                                                                                                                    Drilling Information                                                                                          Material Description and Observations




                                                                                                                                                                                                                                                                                                                                                                            Relative Density
                                                                                                                                                                                                                                                                                                     Classification                                                                                                            DCP TEST
                                                                                                                                                                                                                     Penetration




                                                                                                                                                                                                                                                                                                                                                                                                 Pocket




                                                                                                                                                                                                                                                                                                                                                                            Consistency
                                                                                                                                                                                                                                                                                       Graphic Log


                                                                                                                                                                                                                                                     Samples                                                                         Material Description
                                                                                                                                                                                                                                                                                                                                                                                               Penetrometer




                                                                                                                                                                                                                                                                                                                                                                            Condition
                                                                                                                                                                                                                                                               Recovery




                                                                                                                                                                                                                                                      Tests                                                            soil type: plasticity or particle characteristics,




                                                                                                                                                                                                                                                                                                                                                                            Moisture
                                                                                                                                                                                                                                                                                                                                                                                                  UCS                      Blows per 100 mm
                                                                                                                                                                                                                                                                                                     Symbol
                                                                                                                                                                                                            Method




                                                                                                                                                                                                                                                                                                                        secondary and minor components, colour
                                                                                                                                                                                                                                   Water




                                                                                                                                                                                                                                                     Remarks               RL Depth                                                                                                               (kPa)
                                                                                                                                                                                                                                                                           (m) (m)                                                                                                                             0       5      10      15    20   25




                                                                                                                                                                                                                                                                                                                                                                                                100
                                                                                                                                                                                                                                                                                                                                                                                                200
                                                                                                                                                                                                                                                                                                                                                                                                300
                                                                                                                                                                                                                                                                                                                                                                                                400
                                                                                                                                                                                                                                                                                                                                                                                                500
                                                                                                                                                                                                                                                                                                                      Silty SAND (TOPSOIL), fine to coarse
                                                                                                                                                                                                                                                                                                                      grained, brown, with organics                         D to
                                                                                                                                                                                                                                                                                                                      Silty SAND (FILL), fine to coarse grained,             M
                                                                                                                                                                                                                                                                                                                      brown
                                                                                                                                                                                                                                   Not Encountered




                                                                                                                                                                                                                                                                                                                                                                                                                   Augered to 1.0m
                                                                                                                                                                                                                                                                                 1

                                                                                                                                                                                                                                                                                                                                                                                       L
                                                                                                                                                                                                                                                                                                       SP             SAND, fine to medium grained, pale grey,
                                                                                                                                                                                                            HA




                                                                                                                                                                                                                                                                                                                      (AEOLIAN)

                                                                                                                                                                                                                                                                                                                                                                              M
                                                                                                                                                                                                                                                                                                                                                                                                                   Augered to 2.0m
                                                                                                                                                                                                                                                                                 2




                                                                                                                                                                                                                                                                                                                                                                                     MD
TECTONIC 3.00.2 LIB.GLB Log 1 TECTONIC BOREHOLE 24265.GPJ <<DrawingFile>> 24/9/2024 14:00 10.02.00.04 Datgel Lab and In Situ Tool - DGD | Lib: Tectonic 3.00.2 2021-03-30 Prj: Tectonic 3.00.2 2021-03-30




                                                                                                                                                                                                                                                                                                                                                                                                                   Augered to 3.0m
                                                                                                                                                                                                                                                                                 3
                                                                                                                                                                                                                                                                                                                      Hole Terminated at 3.00 m
                                                                                                                                                                                                                                                                                                                      Target depth




                                                                                                                                                                                                                                                                                 4




                                                                                                                                                                                                                                                                                 5




                                                                                                                                                                                                                                                                                 6




                                                                                                                                                                                                                                                                                 7




                                                                                                                                                                                                                                                                                 8



                                                                                                                                                                                                                      Method                                       Penetration                                        Water                   Samples and Tests                        Moisture Condition               Consistency/Relative Density
                                                                                                                                                                                                                 AD/T-Auger Drilling TC Bit                                 VE - Very Easy        Level (Date)                         U## - Undisturbed Sample (## mm)                    D - Dry                          VS - Very Soft
                                                                                                                                                                                                                 AD/V-Auger Drilling V Bit                                  E - Easy                                                   DS - Disturbed Sample                               M - Moist                        S - Soft
                                                                                                                                                                                                                 RT - Rotary Tri-cone Bit                                                         Inflow                               BDS- Bulk Disturbed Sample                          W - Wet                          F - Firm
                                                                                                                                                                                                                 RD - Rotary Drilling                                       F - Firm                                                   SPT - Standard Penetration Test                                                      VSt - Very Stiff
                                                                                                                                                                                                                                                                                                  Partial Loss
                                                                                                                                                                                                                 NMLC -Rock Core                                            H - Hard                                                                                                                                        H - Hard
                                                                                                                                                                                                                                                                            VH - Very hard       Complete Loss
                                                                                                                                                                                                                 HA - Hand Auger                                                                                                                                                               Plastic Limit                VL - Very Loose
                                                                                                                                                                                                                                                                          Graphic Log/Core Loss                                                                                                                             L   - Loose
                                                                                                                                                                                                                                                                                                                                              Classification Symbols                              < PL                      MD - Medium Dense
                                                                                                                                                                                                                                                                             Core recovered (hatching                                         and Soil Descriptions                                                         D - Dense
                                                                                                                                                                                                                                                                             indicates material)                                                                                                  = PL
                                                                                                                                                                                                                                                                                                                                               Based on Unified Soil                              < PL                      VD - Very Dense
                                                                                                                                                                                                                                                                             Core loss                                                         Classification System                                                        Fr - Friable

Page 30

                                                                                                                                                                                                                                                                                                                                                                                                                                     Borehole No.

                                                                                                                                                                                                                                                                                                                                                                                                                                           BH4
                                                                                                                                                                                                                                                                                                                                                                                                                                     Page 1 of 1

                                                                                                                                                                                                            Engineering Log - Borehole                                                                                                                             Project No.:                     24265

                                                                                                                                                                                                                 Client:                                 Archend                                                                                                   Commenced:                       6/9/2024
                                                                                                                                                                                                                 Project Name:                           Proposed Unit Development                                                                                 Completed:                       6/9/2024
                                                                                                                                                                                                                 Hole Location:                          51 Elanda Street, Sunshine Beach                                                                          Logged By:                       BC
                                                                                                                                                                                                                 Hole Position:                          510912.0 m E 7079249.0 m N MGA2020 Zone 56                                                                Checked By:                      DP
                                                                                                                                                                                                                 Drill Model and Mounting:                                4WD Auger                                                Inclination: -90°               RL Surface:                 No survey
                                                                                                                                                                                                                 Hole Diameter:                                           100 mm                                                   Bearing:     360°               Datum:                      AHD       Operator:             WD

                                                                                                                                                                                                                                    Drilling Information                                                                                          Material Description and Observations




                                                                                                                                                                                                                                                                                                                                                                            Relative Density
                                                                                                                                                                                                                                                                                                     Classification                                                                                                            DCP TEST
                                                                                                                                                                                                                     Penetration




                                                                                                                                                                                                                                                                                                                                                                                                 Pocket




                                                                                                                                                                                                                                                                                                                                                                            Consistency
                                                                                                                                                                                                                                                                                       Graphic Log


                                                                                                                                                                                                                                                     Samples                                                                         Material Description
                                                                                                                                                                                                                                                                                                                                                                                               Penetrometer




                                                                                                                                                                                                                                                                                                                                                                            Condition
                                                                                                                                                                                                                                                               Recovery




                                                                                                                                                                                                                                                      Tests                                                            soil type: plasticity or particle characteristics,




                                                                                                                                                                                                                                                                                                                                                                            Moisture
                                                                                                                                                                                                                                                                                                                                                                                                  UCS                      Blows per 100 mm
                                                                                                                                                                                                                                                                                                     Symbol
                                                                                                                                                                                                            Method




                                                                                                                                                                                                                                                                                                                        secondary and minor components, colour
                                                                                                                                                                                                                                   Water




                                                                                                                                                                                                                                                     Remarks               RL Depth                                                                                                               (kPa)
                                                                                                                                                                                                                                                                           (m) (m)                                                                                                                             0       5      10      15    20   25




                                                                                                                                                                                                                                                                                                                                                                                                100
                                                                                                                                                                                                                                                                                                                                                                                                200
                                                                                                                                                                                                                                                                                                                                                                                                300
                                                                                                                                                                                                                                                                                                                                                                                                400
                                                                                                                                                                                                                                                                                                                                                                                                500
                                                                                                                                                                                                                                                                                                                      Silty SAND (TOPSOIL), fine to medium
                                                                                                                                                                                                                                                                                                       SP             grained, brown, with organics
                                                                                                                                                                                                                                                                                                                      SAND, fine to medium grained, pale grey,
                                                                                                                                                                                                                                                                                                                      (AEOLIAN)

                                                                                                                                                                                                                                                                                                                                                                                       L
                                                                                                                                                                                                                                   Not Encountered




                                                                                                                                                                                                                                                                                                                                                                                                                   Augered to 1.0m
                                                                                                                                                                                                                                                                                 1


                                                                                                                                                                                                                                                                                                                                                                              M
                                                                                                                                                                                                            HA




                                                                                                                                                                                                                                                                                                                                                                                                                   Augered to 2.0m
                                                                                                                                                                                                                                                                                 2

                                                                                                                                                                                                                                                                                                                                                                                     MD
TECTONIC 3.00.2 LIB.GLB Log 1 TECTONIC BOREHOLE 24265.GPJ <<DrawingFile>> 24/9/2024 14:00 10.02.00.04 Datgel Lab and In Situ Tool - DGD | Lib: Tectonic 3.00.2 2021-03-30 Prj: Tectonic 3.00.2 2021-03-30




                                                                                                                                                                                                                                                                                                                                                                                                                   Augered to 3.0m
                                                                                                                                                                                                                                                                                 3
                                                                                                                                                                                                                                                                                                                      Hole Terminated at 3.00 m
                                                                                                                                                                                                                                                                                                                      Target depth




                                                                                                                                                                                                                                                                                 4




                                                                                                                                                                                                                                                                                 5




                                                                                                                                                                                                                                                                                 6




                                                                                                                                                                                                                                                                                 7




                                                                                                                                                                                                                                                                                 8



                                                                                                                                                                                                                      Method                                       Penetration                                        Water                   Samples and Tests                        Moisture Condition               Consistency/Relative Density
                                                                                                                                                                                                                 AD/T-Auger Drilling TC Bit                                 VE - Very Easy        Level (Date)                         U## - Undisturbed Sample (## mm)                    D - Dry                          VS - Very Soft
                                                                                                                                                                                                                 AD/V-Auger Drilling V Bit                                  E - Easy                                                   DS - Disturbed Sample                               M - Moist                        S - Soft
                                                                                                                                                                                                                 RT - Rotary Tri-cone Bit                                                         Inflow                               BDS- Bulk Disturbed Sample                          W - Wet                          F - Firm
                                                                                                                                                                                                                 RD - Rotary Drilling                                       F - Firm                                                   SPT - Standard Penetration Test                                                      VSt - Very Stiff
                                                                                                                                                                                                                                                                                                  Partial Loss
                                                                                                                                                                                                                 NMLC -Rock Core                                            H - Hard                                                                                                                                        H - Hard
                                                                                                                                                                                                                                                                            VH - Very hard       Complete Loss
                                                                                                                                                                                                                 HA - Hand Auger                                                                                                                                                               Plastic Limit                VL - Very Loose
                                                                                                                                                                                                                                                                          Graphic Log/Core Loss                                                                                                                             L   - Loose
                                                                                                                                                                                                                                                                                                                                              Classification Symbols                              < PL                      MD - Medium Dense
                                                                                                                                                                                                                                                                             Core recovered (hatching                                         and Soil Descriptions                                                         D - Dense
                                                                                                                                                                                                                                                                             indicates material)                                                                                                  = PL
                                                                                                                                                                                                                                                                                                                                               Based on Unified Soil                              < PL                      VD - Very Dense
                                                                                                                                                                                                                                                                             Core loss                                                         Classification System                                                        Fr - Friable

Page 31

                                                                                           TERMS USED ON LOGS

DRILLING/EXCAVATION METHOD
AD*        Auger Drilling          RD      Rotary Blade or Drag bit            NQ         Diamond Core - 47 mm
*V         V-Bit                   RT      Rotary Tri-cone bit                 NMLC       Diamond Core - 52 mm
*T         TC-Bit                  RA      Rotary Air                          HQ         Diamond Core - 63 mm
HA         Hand Auger                                                          HMLC       Diamond Core – 63mm
ADH        Hollow Auger                                                        BH         Tractor Mounted Backhoe
                                                                               EX         Tracked Hydraulic Excavator



WATER
GROUNDWATER NOT             The observation of groundwater, whether present or not, was not possible due to drilling water,
OBSERVED                    surface seepage or cave in of the borehole/test pit.
GROUNDWATER NOT            The borehole/test pit was dry soon after excavation. However, groundwater could be present in
ENCOUNTERED                less permeable strata. Inflow may have been observed had the borehole/test pit been left open
                           for a longer period.

SAMPLING AND TESTING
SPT                Standard Penetration Test to AS1289.6.3.1-2004
5,4,10 N=14        5,4,10 = Blows per 150mm. N = Blows per 300mm penetration following 150mm seating
30/65mm            Where practical refusal occurs, the blows and penetration for that interval are reported
RW                 Penetration occurred under the rod weight only
HW                 Penetration occurred under the hammer and rod weight only
HB                 Hammer double bouncing on anvil
DS                 Disturbed sample
BDS                Bulk disturbed sample
FV                 Field vane shear test expressed as uncorrected shear strength (sv = peak value, sr = residual value)
PP                 Pocket penetrometer test expressed as instrument reading in kPa
U50                Thin walled tube sample - number indicates nominal sample diameter in millimetres
DCP                Dynamic cone penetration test
CPT                Electronic cone penetration test
CPTu               Electronic cone penetration test with pore pressure (u) measurement



                                                                                                                       Rev1
                                                                                                                 August 2024

Page 32

                                                                         METHOD OF SOIL DESCRIPTION
                                                                                      USED ON LOGS
CLASSIFICATION AND INFERRED STRATIGRAPHY
Soil is classified and described in borehole and test pit logs using the preferred method given in AS1726 – 2017.
The material properties are assessed in the field by visual/tactile methods.
Particle Size                                                                      Plasticity Properties

 Major          Sub Division           Particle Size
Division
          BOULDERS                     > 200 mm
           COBBLES                    63 to 200 mm
                  Coarse               19 to 63 mm
 GRAVEL           Medium               6.7 to 19 mm
                       Fine           2.36 to 6.7 mm
                  Coarse              0.6 to 2.36 mm
  SAND            Medium              0.21 to 0.6 mm
                   Fine               0.075 to 0.21
                SILT                  0.002 to 0.075
             CLAY                      < 0.002 mm
                                                          NOTE: The U line is an approximate upper bound for most materials.
                                                          Data which plot above the U line may represent unusual/problem soil
                                                          behavior, or unreliable data and should be considered carefully.

MOISTURE CONDITION                                               AS1726 - 2017
Symbol     Term    Description
   D              Dry         Sands and gravels are free flowing. Clays & Silts may be brittle or friable and powdery.
   M             Moist        Soils are darker than in the dry condition & may feel cool. Sands and gravels tend to cohere.
   W              Wet         Soils exude free water. Sands and gravels tend to cohere.

CONSISTENCY AND DENSITY                                         AS1726 - 2017
 Symbol      Term       Undrained Shear                       Symbol        Term              Density Index %        SPT “N” #
                           Strength
    VS           Very Soft             0 to 12 kPa               VL         Very Loose          Less than 15              0 to 4
    S              Soft               12 to 25 kPa                L            Loose               15 to 35              4 to 10
    F              Firm               25 to 50 kPa              MD        Medium Dense             35 to 65           10 to 30
    St             Stiff              50 to 100 kPa              D            Dense                65 to 85           30 to 50
    VSt          Very Stiff          100 to 200 kPa              VD         Very Dense            Above 85           Above 50
     H            Hard             Above 200 kPa
In the absence of test results, consistency and density may be assessed from correlations with the observed behaviour of
the material.
# SPT correlations are not stated in AS1726 – 2017, and may be subject to corrections for overburden pressure and
equipment type.




                                                                                                                                  Rev2
                                                                                                                           August 2024

Page 33

Appendix B
AGS Guidlines - Qualitative Terminology for Use
in Assesing the Risk to Property
Some Guidelines for Hillside Construction




Proposed Unit Development
30 September 2024 | 24265-001-Rev0            2

Page 34

                                      PRACTICE NOTE GUIDELINES FOR LANDSLIDE RISK MANAGEMENT 2007
                                                              APPENDIX C: LANDSLIDE RISK ASSESSMENT
                                    QUALITATIVE TERMINOLOGY FOR USE IN ASSESSING RISK TO PROPERTY


   QUALITATIVE MEASURES OF LIKELIHOOD

Approximate Annual Probability
                                             Implied Indicative Landslide
                                                                                                                     Description                                           Descriptor               Level
Indicative          Notional                    Recurrence Interval
  Value             Boundary
   10-1                5x10-2
                                              10 years                           The event is expected to occur over the design life.                                ALMOST CERTAIN                   A
                                                                    20 years     The event will probably occur under adverse conditions over the
        -2
   10                                      100 years
                                                                                 design life.
                                                                                                                                                                     LIKELY                           B
                            -3
     -3               5x10                                       200 years
   10                                      1000 years                            The event could occur under adverse conditions over the design life.                POSSIBLE                         C
                      5x10-4                                     2000 years
                                                                                 The event might occur under very adverse circumstances over the
   10-4                                   10,000 years
                                                                                 design life.
                                                                                                                                                                     UNLIKELY                         D
     -5               5x10-5                                     20,000 years
   10                                                                            The event is conceivable but only under exceptional circumstances
                                         100,000 years                                                                                                               RARE                             E
                                                                                 over the design life.
     -6                5x10-6                                    200,000 years
   10                                   1,000,000 years                          The event is inconceivable or fanciful over the design life.                        BARELY CREDIBLE                  F
   Note:     (1)   The table should be used from left to right; use Approximate Annual Probability or Description to assign Descriptor, not vice versa.


   QUALITATIVE MEASURES OF CONSEQUENCES TO PROPERTY

  Approximate Cost of Damage
                                                                                               Description                                                                 Descriptor               Level
Indicative           Notional
  Value              Boundary
                                         Structure(s) completely destroyed and/or large scale damage requiring major engineering works for
   200%                                                                                                                                                             CATASTROPHIC                      1
                                         stabilisation. Could cause at least one adjacent property major consequence damage.
                     100%
                                         Extensive damage to most of structure, and/or extending beyond site boundaries requiring significant
   60%                                                                                                                                                              MAJOR                             2
                                         stabilisation works. Could cause at least one adjacent property medium consequence damage.
                       40%
                                         Moderate damage to some of structure, and/or significant part of site requiring large stabilisation works.
   20%                                                                                                                                                              MEDIUM                            3
                                         Could cause at least one adjacent property minor consequence damage.
                       10%
    5%                 1%                Limited damage to part of structure, and/or part of site requiring some reinstatement stabilisation works.                 MINOR                             4
                                         Little damage. (Note for high probability event (Almost Certain), this category may be subdivided at a
   0.5%                                                                                                                                                             INSIGNIFICANT                     5
                                         notional boundary of 0.1%. See Risk Matrix.)
   Notes:    (2)   The Approximate Cost of Damage is expressed as a percentage of market value, being the cost of the improved value of the unaffected property which includes the land plus the
                   unaffected structures.
             (3)   The Approximate Cost is to be an estimate of the direct cost of the damage, such as the cost of reinstatement of the damaged portion of the property (land plus structures), stabilisation
                   works required to render the site to tolerable risk level for the landslide which has occurred and professional design fees, and consequential costs such as legal fees, temporary
                   accommodation. It does not include additional stabilisation works to address other landslides which may affect the property.
             (4)   The table should be used from left to right; use Approximate Cost of Damage or Description to assign Descriptor, not vice versa


                                                                    Australian Geomechanics Vol 42 No 1 March 2007
   68039 Landslide Risk Management Issued 10/7/07

Page 35

                                       PRACTICE NOTE GUIDELINES FOR LANDSLIDE RISK MANAGEMENT 2007
               APPENDIX C: – QUALITATIVE TERMINOLOGY FOR USE IN ASSESSING RISK TO PROPERTY (CONTINUED)


      QUALITATIVE RISK ANALYSIS MATRIX – LEVEL OF RISK TO PROPERTY
                     LIKELIHOOD                                                  CONSEQUENCES TO PROPERTY (With Indicative Approximate Cost of Damage)
                                          Indicative Value of         1: CATASTROPHIC                 2: MAJOR                3: MEDIUM                4: MINOR                    5:
                                         Approximate Annual                 200%                         60%                      20%                     5%                INSIGNIFICANT
                                             Probability                                                                                                                         0.5%
A –    ALMOST CERTAIN                             10-1                          VH                         VH                      VH                       H                   M or L (5)
                                                    -2
B -    LIKELY                                     10                            VH                         VH                       H                       M                       L
C -    POSSIBLE                                   10-3                          VH                          H                       M                       M                      VL

D -    UNLIKELY                                   10-4                           H                         M                        L                       L                      VL
                                                    -5
E -    RARE                                       10                             M                          L                       L                      VL                      VL
                                                    -6
F -    BARELY CREDIBLE                            10                             L                         VL                      VL                      VL                      VL
      Notes:   (5)   For Cell A5, may be subdivided such that a consequence of less than 0.1% is Low Risk.
               (6)   When considering a risk assessment it must be clearly stated whether it is for existing conditions or with risk control measures which may not be implemented at the current
                     time.


      RISK LEVEL IMPLICATIONS
                        Risk Level                                                                                  Example Implications (7)
                                                                 Unacceptable without treatment. Extensive detailed investigation and research, planning and implementation of treatment
        VH                      VERY HIGH RISK                   options essential to reduce risk to Low; may be too expensive and not practical. Work likely to cost more than value of the
                                                                 property.
                                                                 Unacceptable without treatment. Detailed investigation, planning and implementation of treatment options required to reduce
         H                           HIGH RISK
                                                                 risk to Low. Work would cost a substantial sum in relation to the value of the property.
                                                                 May be tolerated in certain circumstances (subject to regulator’s approval) but requires investigation, planning and
         M                      MODERATE RISK                    implementation of treatment options to reduce the risk to Low. Treatment options to reduce to Low risk should be
                                                                 implemented as soon as practicable.
                                                                 Usually acceptable to regulators. Where treatment has been required to reduce the risk to this level, ongoing maintenance is
         L                           LOW RISK
                                                                 required.
                                                                 Acceptable. Manage by normal slope maintenance procedures.
         VL                      VERY LOW RISK

       Note:   (7)   The implications for a particular situation are to be determined by all parties to the risk assessment and may depend on the nature of the property at risk; these are only
                     given as a general guide.




                                                                      Australian Geomechanics Vol 42 No 1 March 2007
      68039 Landslide Risk Management        Issued 10/7/07

Page 36

     PRACTICE NOTE GUIDELINES FOR LANDSLIDE RISK MANAGEMENT 2007



          APPENDIX G - SOME GUIDELINES FOR HILLSIDE CONSTRUCTION

                 GOOD ENGINEERING PRACTICE                                                            POOR ENGINEERING PRACTICE
ADVICE
GEOTECHNICAL     Obtain advice from a qualified, experienced geotechnical practitioner at early       Prepare detailed plan and start site works before
ASSESSMENT       stage of planning and before site works.                                             geotechnical advice.
PLANNING
SITE PLANNING    Having obtained geotechnical advice, plan the development with the risk              Plan development without regard for the Risk.
                 arising from the identified hazards and consequences in mind.
DESIGN AND CONSTRUCTION
                 Use flexible structures which incorporate properly designed brickwork, timber        Floor plans which require extensive cutting and
                 or steel frames, timber or panel cladding.                                           filling.
 HOUSE DESIGN
                 Consider use of split levels.                                                        Movement intolerant structures.
                 Use decks for recreational areas where appropriate.
SITE CLEARING    Retain natural vegetation wherever practicable.                                      Indiscriminately clear the site.
    ACCESS &     Satisfy requirements below for cuts, fills, retaining walls and drainage.            Excavate and fill for site access before
   DRIVEWAYS     Council specifications for grades may need to be modified.                           geotechnical advice.
                 Driveways and parking areas may need to be fully supported on piers.
EARTHWORKS       Retain natural contours wherever possible.                                           Indiscriminatory bulk earthworks.
                 Minimise depth.                                                                      Large scale cuts and benching.
      CUTS       Support with engineered retaining walls or batter to appropriate slope.              Unsupported cuts.
                 Provide drainage measures and erosion control.                                       Ignore drainage requirements
                 Minimise height.                                                                     Loose or poorly compacted fill, which if it fails,
                 Strip vegetation and topsoil and key into natural slopes prior to filling.           may flow a considerable distance including
                 Use clean fill materials and compact to engineering standards.                       onto property below.
      FILLS      Batter to appropriate slope or support with engineered retaining wall.               Block natural drainage lines.
                 Provide surface drainage and appropriate subsurface drainage.                        Fill over existing vegetation and topsoil.
                                                                                                      Include stumps, trees, vegetation, topsoil,
                                                                                                      boulders, building rubble etc in fill.
 ROCK OUTCROPS   Remove or stabilise boulders which may have unacceptable risk.                       Disturb or undercut detached blocks or
  & BOULDERS     Support rock faces where necessary.                                                  boulders.
                 Engineer design to resist applied soil and water forces.                             Construct a structurally inadequate wall such as
                 Found on rock where practicable.                                                     sandstone flagging, brick or unreinforced
   RETAINING
                 Provide subsurface drainage within wall backfill and surface drainage on slope       blockwork.
     WALLS
                 above.                                                                               Lack of subsurface drains and weepholes.
                 Construct wall as soon as possible after cut/fill operation.
                 Found within rock where practicable.                                                 Found on topsoil, loose fill, detached boulders
                 Use rows of piers or strip footings oriented up and down slope.                      or undercut cliffs.
   FOOTINGS
                 Design for lateral creep pressures if necessary.
                 Backfill footing excavations to exclude ingress of surface water.
                 Engineer designed.
                 Support on piers to rock where practicable.
SWIMMING POOLS   Provide with under-drainage and gravity drain outlet where practicable.
                 Design for high soil pressures which may develop on uphill side whilst there
                 may be little or no lateral support on downhill side.
   DRAINAGE
                 Provide at tops of cut and fill slopes.                                              Discharge at top of fills and cuts.
                 Discharge to street drainage or natural water courses.                               Allow water to pond on bench areas.
    SURFACE      Provide general falls to prevent blockage by siltation and incorporate silt traps.
                 Line to minimise infiltration and make flexible where possible.
                 Special structures to dissipate energy at changes of slope and/or direction.
                 Provide filter around subsurface drain.                                              Discharge roof runoff into absorption trenches.
                 Provide drain behind retaining walls.
   SUBSURFACE
                 Use flexible pipelines with access for maintenance.
                 Prevent inflow of surface water.
                 Usually requires pump-out or mains sewer systems; absorption trenches may            Discharge sullage directly onto and into slopes.
    SEPTIC &
                 be possible in some areas if risk is acceptable.                                     Use absorption trenches without consideration
    SULLAGE
                 Storage tanks should be water-tight and adequately founded.                          of landslide risk.
   EROSION       Control erosion as this may lead to instability.                                     Failure to observe earthworks and drainage
  CONTROL &      Revegetate cleared area.                                                             recommendations when landscaping.
 LANDSCAPING
DRAWINGS AND SITE VISITS DURING CONSTRUCTION
   DRAWINGS      Building Application drawings should be viewed by geotechnical consultant
   SITE VISITS   Site Visits by consultant may be appropriate during construction/
INSPECTION AND MAINTENANCE BY OWNER
   OWNER’S       Clean drainage systems; repair broken joints in drains and leaks in supply
RESPONSIBILITY   pipes.
                 Where structural distress is evident see advice.
                 If seepage observed, determine causes or seek advice on consequences.




                        Australian Geomechanics Vol 42 No 1 March 2007                                                                  113

Page 37

      PRACTICE NOTE GUIDELINES FOR LANDSLIDE RISK MANAGEMENT 2007




114             Australian Geomechanics Vol 42 No 1 March 2007

Page 38

a e
@€nic
‘e

Appendix C
Limitations

 

Page 39

Limitations

This document has been prepared for the purpose outlined in Tectonic’s proposal and no responsibility is
accepted for the use of this document, in whole or in part, for any other purpose.
The scope of Tectonic’s Services are as described in Tectonic’s proposal, and are subject to restrictions
and limitations. Tectonic did not perform a complete assessment of all possible conditions or
circumstances that may exist at the site referenced in the report. If a service is not expressly indicated, do
not assume it has been provided. If a matter is not addressed, do not assume that any determination has
been made by Tectonic in regards to it.
Conditions may exist which were undetectable given that economic and time constraints limit the
practical extent of geotechnical investigation. Variations in conditions may occur between investigation
locations, and there may be special conditions pertaining to the site which have not been revealed by the
investigation and which have not therefore been taken into account in the document. Where variations
exist on site, additional studies and actions may be required.
Tectonic’s opinions are based upon information that existed at the time that the work was performed.
The passage of time, man-made or natural events, may alter the site conditions. It is understood that the
Services undertaken allowed Tectonic to form an opinion of the actual conditions of the site at the time
the site was visited and cannot be used to assess the effect of any subsequent changes in the quality of
the site, or its surroundings, or any laws or regulations.
Any assessments made in the preparation of this document are based on the conditions indicated from
published sources and the findings of the investigation described. Actual subsurface conditions may
differ from those indicated in the document (e.g. between boreholes or test pits). No warranty is
included, either express or implied, that the actual conditions will conform exactly to the assessments
contained in this document.
Where data supplied by the client or other external sources, including previous site investigation data,
have been used, it has been assumed that the information is correct unless otherwise stated. No
responsibility is accepted by Tectonic for incomplete or inaccurate data supplied by others.
This document is provided for the sole use by the Client and its professional advisers. No responsibility
whatsoever for the contents of this document will be accepted to any person other than the Client. Any
use which a third party makes of this document, or any reliance on or decisions to be made based on it,
is the responsibility of such third parties. Tectonic accepts no responsibility for damages, if any, suffered
by any third party as a result of decisions made or actions based on this document.




Limitations
August 2024 | Rev2

Page 40

             PO Box 899              tectonicgeo.com.au   [email protected]
          Buderim
Proposed Unit      QLD 4555
              Development
30 September 2024 | 24265-001-Rev0                                                   4

Used in these records

About this file

File size
6.8 MB (large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

Geotechnical Investigation.pdf · 6.8 MB (large file)

The download may take up to a minute.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.