Skip to the record
For the highest quality transcripts.

Council archive · source document

Geotechnical Investigation · MCU24/0153

of 40

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

4.4            Subsurface Conditions
Detailed descriptions of the subsurface conditions encountered in the boreholes are provided in the
borehole reports attached in Appendix A, along with definition sheets which describe terms and
abbreviations used on the reports. The subsurface conditions encountered in the boreholes are
summarised as follows:
▪     Topsoil – comprising loose silty sand to depths of 0.1 m to 0.2 m below ground level (BGL); then
▪     Fill – comprising loose silty sand to depths of between 0.4 m and 0.1.3 m BGL; then
▪     Natural Sands – comprising poorly graded sands mostly being loose to depths of between 1.4 m
      and 2.6 m BGL; then becoming medium dense and increasing to dense below depths of about
      2.8 to 3.8 m BGL.
Table 1 below summarises the subsurface profile in each borehole.

Table 1: Summary of Subsurface Conditions

                                                                                       Medium         Dense (or
    Borehole No.      Topsoil              Fill                 Loose Sands
                                                                                       Dense Sands    denser) Sands
                      0.0 – 0.2            0.2 – 0.4            0.4 – 1.5              1.5 – 2.8      2.8 – 8.0TD
    BH1


                      0.0 – 0.1            0.1 – 0.4            0.4 – 1.4              1.4 – 3.0TD    3.3* – 4.7DCP
    BH2


                      0.0 – 0.1            0.1 – 1.3            1.3 – 2.6              2.6 – 3.0 TD   3.7* – 4.8DCP
    BH3


    BH4               0.0 – 0.1            -                    0.1 – 1.7              1.7 – 3.0TD    3.8 – 4.8TD
Notes: 1.          Depths noted in m BGL at time of investigation (22 February 2022)

2.        NE denotes not encountered

3.        TD denotes borehole terminated at target depth


4.        * inferred from DCP testing

5.        DCP denotes DCP termination depth




A site classification ‘soil test’ report by Australian Soil Investigations (ASI) (Ref. Report No. 230154(S),
dated 12 June 2023) comprised the drilling of two boreholes (designated BH1 and BH2) in accessible
locations to the east of the property. Rubbish was noted by ASI in BH2 at a depth of 0.7 m BGL. Three
boreholes (designated BH2, BH2A and BH2B) were drilled by Tectonic in this area to delineate the extent
of this rubbish, however, no deleterious material was encountered at those locations.
ASI has classified the site as Class P, as per AS2870, due to poor bearing capacity and fill; however, has
stated that the site would have the shrink-swell characteristics of a Class S site.




Proposed Unit Development
30 September 2024 | 24265-001-Rev0                                                                                    6

Used in these records

About this file

File size
6.8 MB (large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

Geotechnical Investigation.pdf · 6.8 MB (large file)

The download may take up to a minute.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.