Skip to the record
Noosa's #1 Council Tracker.

Council archive · source document

SUPERSEDED - MCU13/0215.01 Change to Existing Approval

of 1

Text shows just the words. Original shows the document exactly as it was published.

Officer:	Jack Lewis
Direct Telephone:	07 53296236
Our Reference:	JLEWIS:MCU13/0215.01
Your Reference:	15225
22 September 2015

Aldev Holdings Pty Ltd
C/- KHA Development Managers
PO Box  6380
MAROOCHYDORE BC  QLD  4558

[email protected]

Dear Sir/Madam

Change to an Existing Approval
Sustainable Planning Act 2009

I refer to your request to make a permissible change to an existing approval.  On 21 September 2015, Council decided your requested changes.

Details of the decision are as follows:
1.	APPLICATION DETAILS

Application No:	MCU13/0215.01
Street Address:	43 Elanda St SUNSHINE BEACH  QLD  4567
Real Property Description:	Lot 1 SP 230070
Planning Scheme:	The Noosa Plan (16 September 2013)

2.	DECISION DETAILS

Council on 3 February 2014 decided to issue the following type of approval:
Development Permit for Material Change of Use - Multiple dwelling Type 4 Conventional - 5 units

In relation to the request to make a change to the existing approval, Council on 21 September 2015 decided to:
Approve a change to the development approval to read as follows:
Development Permit for Material Change of Use – Multiple Dwelling Type 4 Conventional - 7 units.
B.	Approve a change to Conditions 2, 3, 12 & 21.
C.	Change Advisory Note 3.
D.	Amend Item 6 – Approved Plans to reflect the change to condition 2.

3.	RELEVANT PERIOD OF APPROVAL

The relevant period for this development approval is 4 years starting the day that this development approval takes effect.

4.	ASSESSMENT MANAGER CONDITIONS

When conditions must be Complied With
Unless otherwise stated, all conditions of this Decision Notice must be complied with prior to the use commencing, and then compliance maintained at all times while the use continues.

Approved Plans
Development undertaken in accordance with this approval must generally comply with the approved plans of development. The approved plans are listed in the following table unless otherwise amended by these conditions.

Plan No.	Rev.	Plan/Document Name	Date
7032/DA/00		Perspective View drawn by Blackburne Jackson Design	
7032/DA/01	13	Site Plan drawn by Blackburne Jackson Design	27/08/2015
7032/DA/02	13	Floor Plan Basement drawn by Blackburne Jackson Design	27/08/2015
7032/DA/03	13	Floor Plan Ground Level drawn by Blackburne Jackson Design	27/08/2015
7032/DA/04	13	Floor Plan Ground Level 1 drawn by Blackburne Jackson Design	27/08/2015
7032/DA/05	13	Floor Plan Ground Level 2 drawn by Blackburne Jackson Design	27/08/2015
7032/DA/06	13	Roof Plan drawn by Blackburne Jackson Design	27/08/2015
7032/DA/07	13	Upper Roof Plan drawn by Blackburne Jackson Design	27/08/2015
7032/DA/08	13	Elevations drawn by Blackburne Jackson Design	27/08/2015
7032/DA/09	13	Elevations drawn by Blackburne Jackson Design	27/08/2015

Building Height
The maximum height of the development must not exceed 12m metres above the existing natural ground levels.

Certification must be submitted to Council from a Licensed Surveyor which certifies that the building does not exceed the maximum height requirement of this Decision Notice.

Performance Bond
Security in the form of a cash bond or trading bank guarantee to the sum of $10,000 must be submitted to Council, to secure performance of all conditions of this approval, prior to the issue of a Development Permit for Operational Works.  The cash bond or trading bank guarantee will be returned on performance of the conditions of approval less any costs incurred by Council in respect of enforcing performance of this permit.  Council reserves the right to call upon the bond or guaranteed sum to effect compliance with condition.

Building Appearance
All air conditioning units or other mechanical equipment must be located at ground level or otherwise fully enclosed or screen such that they are not visible from the street frontages nor adjoining properties.

All deck and balcony areas above ground floor must not be enclosed by permanent fixtures such as shutters, louvers, glass panelling or the like, expect where required to satisfy any privacy condition of this Decision Notice.

Fencing and Walls
Any street fencing must be set back an average of 1 metre from the front property boundary.  Any fencing on the front boundary must either:
not exceed a maximum height of 1.2m or
be of open construction

The area of land between the fence and the front property boundary must be densely landscaped to screen any fencing from the street.

Clothes Drying Areas
Each dwelling unit must be provided with access to an outdoor clothes line which is screened from public view.

Community Management Statement
Any proposed Community Management Statement required for the development pursuant to the Body Corporate and Community Management Act 1997 must be submitted to Council for endorsement at the same time as submission of the Building Format Plan (or similar) to Council for compliance assessment.

Landscaping
The development site must be landscaped. The works must be undertaken in accordance with an Operational Works approval and The Noosa Plan for that specific area and must include in particular:.
Suitable native screening vegetation shall be planted along the side boundaries of the site to assist in reducing the building bulk;
A minimum of 4 x 45L street trees within the Elanda Street frontage; and
Appropriate native screening species to be planted along the podium level beds around the basement carpark.

Existing trees on the site and within road reserves are to be retained, except where required to be removed due to building operations or the conduct of the approved use. These landscape plans required to be submitted are to denote areas of existing vegetation or existing trees proposed or required to be retained.

Cleared vegetation is to be suitably processed by one of the following methods and removed from the site:-
Processing through a woodchipper or shredder. The resulting mulch is to be stockpiled loose in heaps of less than 1000 cubic metres, less than 2.5 metres high with a minimum of 10 metres between edges of heaps.
Disposal for firewood.
Disposal for landscaping purposes.
Transport to alternative site for breaking down materials provided that all necessary permits have been obtained to allow the alternate site to be used for this purpose.
The disposal method for clearing works is to be submitted in conjunction with an application for a Development Permit for Operational Work. The Applicant is advised that other methods may be considered provided full details of the method are submitted.
The Applicant is advised that burning off is an unacceptable method of disposal.

Environmental Health
Where the development involves the removal, relocation or demolition of a building, a Waste Management Plan (construction and demolition) shall be submitted prior to demolition, removal or relocation of any building other than a shed.
Waste Management Plans (construction and demolition) are required to be submitted in accordance with Planning Scheme Policy 11, Waste Management Plans see table below.
Waste storage areas are to provide for adequate separation of all reusable, recyclable and waste materials. These shall be located so that they are convenient and safe to use. (Refer to Noosa Council Waste Management Code)
The Plan shall contain the following information:
The site area for the storage and separation of waste is to be shown on the plan drawings accompanying the application.
A waste management table as indicated below is to be completed showing how waste material is to be segregated - recycled – reused or disposed.

MATERIALS ON-SITE	DESTINATION
	Re-use and Recycling	Disposal
Expected waste materials	Estimated volume(m³)	On-site            *specify proposed re-use or on-site recycling methods	Off-site              *specify contractor and recycling outlet	*specify contractor and landfill site or other disposal site
Excavation material				
Green waste				
Bricks				
Concrete				
Timber-please specify				
Plasterboard				
Metals - please specify				
Asbestos				
Other - please specify				
Note * If a demolition contractor is undertaking works, then the Waste Management table is to be completed by the demolition contractor.
The purpose of the Waste Management Plan is to facilitate the segregation of waste for the effective reuse and recycling of such materials. Additionally Council rewards those who segregate waste by significantly reducing disposal fees at the landfill some items are free. Higher gate fees are charged for loads of mixed waste.

The developer must provide waste storage and disposal facilities in accordance with Planning Scheme Policy “Waste Management Multi-Dwellings and Commercial and Industrial Premises”, including an external imperviously paved area correctly sized for all refuse and recycling containers and suitably screened from public places and neighbouring properties.

Noise emission from mechanical equipment (air conditioners, refrigeration equipment or pool pumps etc) shall comply with the following requirements:
The equipment shall be installed and located in a manner that prevents excessive noise in accordance with Council’s Local Law No. 12 - Control of Nuisances.  Infringement Notices (on-the-spot fines) may apply for offences.
A person must not use equipment on any day if it makes or causes noise to be made:
From 10pm to 7am: More than the lower of either –
40 dB(A)
3 dB(A) above the background noise level
From 7am to 7pm: More than the lower of either –
50 dB(A)
5 dB(A) above the background noise level
From 7pm to 10pm: More than 3 dB(A) above the background noise level.
Pool pumps must not be audible at an effected premises between 10pm-7am

Noise from residential building works shall comply with the following –
Limited to between 7:00am to 6:30pm Monday to Saturday.
All reasonable measures are taken to minimise noise emissions.
Not permitted on Sunday or public holidays.

External Works
Elanda Street must be upgraded for the length of its frontage to the subject site.  The works must be undertaken in accordance with an Operational Works approval and must include in particular:
Construction of kerb and channelling to match with, and connect to, the existing adjoining sections of kerb and channelling.
Widening and sealing of the existing road pavement in accordance with Council’s requirements and standards, including any required pavement correction to the existing pavement.
Construction of a pedestrian 1.5m wide concrete footpath in accordance with Council’s standard drawing SEQ R-065 and with a meandering alignment to match smoothly with the existing adjoining concrete footpaths. The pathway must be incorporated in the landscaping design for the frontage works.

Site Access and Driveways
A sealed access driveway must be provided from Elanda Street to all parking and manoeuvring areas of the development. The works must be undertaken in accordance with an Operational Works approval and must include in particular:
A driveway crossover in accordance with IPWEAQ standard drawing SEQ R- 051 and to grades that prevent vehicles from scraping and/or bottoming whilst also allowing pedestrians movements along the footpath without any step or level difference.  The driveway crossover design must also ensure no stormwater runoff is directed from the street into the site.
For pedestrian safety between vehicles exiting the site and pedestrians on the footpath, the driveway and any associated fencing or vegetation near the driveway shall comply with the minimum sight line requirements as defined in AS 2890.1, section 3.2.4.
A driveway width of 5.5 metres, extending for a minimum distance of 6 metres from the kerb line into the site.
Adjustment to any adjoining concrete footpath, if required, to achieve smooth and compliant grades.

Car Parking
Car parking must be provided within the site generally as shown on the approved plans, except as modified herein.  The works must be undertaken in accordance with an Operational Works approval and must include in particular:
The car parking must be in compliance with the provisions of AS/NZS 2890.1-2004 for user class 1A with allowance for vehicles to enter and leave the site in a forward gear and with a minimum head clearance (headroom) at any point of 2.2m.

All car parking areas and access driveways must be maintained exclusively for vehicle parking and manoeuvring and kept in a tidy and safe condition at all times.

Stormwater Drainage
The site must be provided with a stormwater drainage system connecting to a lawful point of discharge.  The works must be undertaken in accordance with an Operational Works approval and be in accordance with a design prepared and certified by a suitably qualified and experienced registered professional. The design must be in accordance with the relevant sections of QUDM, be supported by a detailed stormwater drainage report and include in particular:
Where it is considered effective and practical roof runoff should be directed to the frontage of the site and discharged into the street’s kerb and channel drainage system. Please note that the maximum discharge at any one location is 25 l/sec.
A Stormwater detention and infiltration system to cater for runoff from the development.  The design of the infiltration system must also address any potential impacts on adjoining properties as a result of stormwater seepage from the infiltration system.
An ongoing maintenance plan for the detention and infiltration system to ensure proper performance of the system.
A grease/oil arrestor/gross pollutant trap shall be provided on site for the treatment of stormwater runoff from the car parking areas and the driveway prior to being permitted to discharge into stormwater detention/infiltration system.
An ongoing maintenance plan for the grease/oil arrestor/gross pollutant trap to ensure proper performance of the system.

Stormwater runoff from the development must be disposed of on-site without causing scour or damage to the subject site or any adjoining property.

Earthworks
Any earthworks required on site shall be carried out in accordance with Council’s Planning Scheme Policy PSP5 – Engineering Design Standards.

Earthworks carried out on site shall not affect the structural integrity of any of the existing fences or structures that border the development site.  Fences that are affected shall be replaced prior to the Building Certifier issuing the Certificate of Classification.  In this regard any fences to be replaced shall be clearly shown on the plans submitted for Operational Works approval.

Site Stability
Prior to obtaining a Development Permit for Operational Works, a Geotechnical Engineer or similar qualified expert shall assess the soil condition on site, determine the soil classification, establish whether any measures are required to protect the stability of adjoining buildings and/or structures and/or land, and make recommendations on the type of foundation system(s) and soil retention methods best suited for the proposed development. The recommendations of the report shall be incorporated into the design and construction of the proposed development.

An existing conditions survey of the adjoining properties shall be carried out and submitted to Council 10 days prior to the commencement of the operational works for records purpose and future reference if required.

Water and Sewerage
Construction activities must not impede the access of Unitywater or Fire Brigade personnel to vital infrastructure (eg. valves, fire hydrants and sewer access chambers).

The fire-fighting demand on Unitywater’s water supply system from the development must not exceed 15 litres per second.

A single Unitywater installed primary water meter must be provided immediately inside the property boundary.  Additional water meters must be installed for each title of a community title or sub-lease scheme. Meters must be Unitywater approved, installed in accordance with Unitywater requirements and remain accessible at all times for reading and maintenance purposes and in accordance with the Unitywater Sub-Meter policy.

Water meters must be located on alternative boundaries to electrical pillars.

Buildings and other structures must maintain a minimum clearance of 1.5 metres from Unitywater sewer mains, and 1.0 metre from a sewer manhole chamber or sewer inspection opening.

Easements of between 3 and 10 metres must be provided over all Unitywater sewers located within property boundaries in accordance with the SEQ standards. Easements shall be centred over the pipe. Easement terms shall be the most current registered dealing held by the Department of Natural Resources & Mines and shall not be altered or amended.

If the level of the existing sewer manhole is to be adjusted it must be so to suit the proposed finished surface levels. Work must be undertaken by Unitywater at the applicant’s cost or by the applicant’s private contractors following submission to Council of an Operational Works application and approval of the application.

Storm water retention systems and gross pollutant traps must maintain a minimum clearance of 1.5 metres from Unitywater water supply and sewerage infrastructure.

Tree plantings must maintain a minimum horizontal clearance of 1.0 metre from Unitywater water mains and 1.5 metres from Unitywater sewerage mains. Landscaping plants within these clearances must be low growing when mature, and suitable approved varieties.

Construction works undertaken in the vicinity of Unitywater water supply or sewerage infrastructure must not adversely affect the integrity of the infrastructure. All costs associated with repair, replacement or alteration of infrastructure must be met by the applicant.

5.	REFERRAL AGENCIES

Not Applicable.

6.	APPROVED PLANS

The following plans are Approved Plans for the development:
Approved Plans
Plan No.	Rev.	Plan/Document Name	Date
7032/DA/00		Perspective View drawn by Blackburne Jackson Design	
7032/DA/01	13	Site Plan drawn by Blackburne Jackson Design	27/08/2015
7032/DA/02	13	Floor Plan Basement drawn by Blackburne Jackson Design	27/08/2015
7032/DA/03	13	Floor Plan Ground Level drawn by Blackburne Jackson Design	27/08/2015
7032/DA/04	13	Floor Plan Ground Level 1 drawn by Blackburne Jackson Design	27/08/2015
7032/DA/05	13	Floor Plan Ground Level 2 drawn by Blackburne Jackson Design	27/08/2015
7032/DA/06	13	Roof Plan drawn by Blackburne Jackson Design	27/08/2015
7032/DA/07	13	Upper Roof Plan drawn by Blackburne Jackson Design	27/08/2015
7032/DA/08	13	Elevations drawn by Blackburne Jackson Design	27/08/2015
7032/DA/09	13	Elevations drawn by Blackburne Jackson Design	27/08/2015

7.	REFERENCED DOCUMENTS

Not Applicable.

8.	ADVISORY NOTES

The following notes are included for guidance and information purposes only and do not form part of the assessment manager conditions:
The Building and Construction Industry (Portable Long Service Leave) Levy must be paid prior to the issue of a development permit where one is required for the 'Building and Construction Industry'.  This applies to Building Works, Operational Works and Plumbing and Drainage Works applications, as defined under the Sustainable Planning Act 2009, where the works are $80,000 or more and matching the definition of 'Building and Construction Industry' under the Building and Construction Industry (Portable Long Service Leave) Act 1991. Council will not be able to issue a Decision Notice without receipt of details that the Levy has been paid.  Should you require clarification in regard to the amendments to the Building and Construction Industry (Portable Long Service Leave) Act 1991, you should contact QLeave on 1800 803 481 (free call) or (07) 3212 6855
Connection to Unitywater live water mains and the Unitywater live sewer system must be undertaken by Unitywater at the applicant’s cost.
This Development Permit for a “Change to Existing Approval” will trigger an “Infrastructure Charge Notice” to be issued in accordance with Council’s “Charges Resolution” made pursuant to the Sustainable Planning Act 2009  and in conjunction with the State Planning Regulatory Provision (adopted charges).
This Infrastructure Charge relates:
Only to the “Change to Existing Approval” to increase the previously approval quantity by 2 additional units; and
Is additional to the earlier Infrastructure Charges Notice N1001 that also remains applicable to the original development approval for 5 units.

9.	PROPERTY NOTES

Not Applicable.

10.	PRELIMINARY APPROVAL OVERRIDING PLANNING SCHEME

Not Applicable.

11.	FURTHER DEVELOPMENT PERMITS REQUIRED

Development Permit for Operational Work (Landscaping, Carparking & Access, Frontage Works, Stormwater Drainage & Detention and Infiltration System, Road Widening & Kerb & Channel and Erosion & Sediment Control)
Development Permit for Building Work

12.	SELF ASSESSABLE CODES

Not Applicable.

13.	SUBMISSIONS

Not Applicable.

14.	REASONS / GROUNDS FOR APPROVAL DESPITE CONFLICT WITH SCHEME

Not Applicable.

15.	RIGHTS OF APPEAL

You are entitled to appeal against this decision.  A copy of the relevant appeal provisions from the Sustainable Planning Act 2009 is attached.

During the appeal period, you as the applicant may suspend your appeal period and make written representations to Council about the conditions contained within the development approval.  If Council agrees or agrees in part with the representations, a “negotiated decision notice” will be issued.  Only one “negotiated decision notice” may be given.  Taking this step will defer your appeal period, which will commence again from the start the day after you receive a “negotiated decision notice”.

16.	OTHER DETAILS

If you wish to obtain more information about Council’s decision, electronic copies are available on line at www.noosa.qld.gov.au, or at Council Offices.

DECISION NOTICE HISTORY Original Decision Notice (3 February 2015) Change to an Existing Approval (21 September 2015)

Yours faithfully

DENIS WALLACE
COORDINATOR - PLANNING

Encl. 	Infrastructure Charges Notice
Approved Plans/Documents
Appeal Rights

cc	Unitywater

	Appeal Rights SUSTAINABLE PLANNING ACT 2009 & SUSTAINABLE PLANNING REGULATION 2009

The following is an extract from the Sustainable Planning Act 2009 (Chapter 7)

466 	Appeals about decisions relating to permissible changes
(1) 	For a development approval given for a development application, the following persons may appeal to the court against a decision on a request to make a permissible change to the approval—
(a) 	if the responsible entity for making the change is the assessment manager for the application—
(i) 	the person who made the request; or
(ii) 	an entity that gave a notice under section 373 or a pre-request response notice about the request;
(b) 	if the responsible entity for making the change is a concurrence agency for the application—the person who made the request.
(2) 	The appeal must be started within 20 business days after the day the person is given notice of the decision on the request under section 376.
(3) 	Also, a person who has made a request under section 369 may appeal to the court against a deemed refusal of the request.
(4)	An appeal under subsection (3) may be started at any time after the last day the decision on the matter should have been made.

[word/footer1.xml]
Page 10 of 11

[word/footer2.xml]
Page 1 of 11
			
		
					PO Box 141		P. (07) 5329 6500	[email protected]	
	TEWANTIN  QLD  4565	F. (07) 5329 6501	www.noosa.qld.gov.au

[word/header3.xml]
MCU13/0215.01

[Attachment: image4.png (image text)]
 
 
 

 
 
 

a
mm

  

NOOSA
COUNCIL

Used in these records

About this file

File size
109 KB (small file)
File type
DOCX

No other editions are linked here.

Original file

Log in to download the original file

SUPERSEDED - MCU13_0215.01 Change to Existing Approval.docx · 109 KB (small file)

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.