Original source · versioned page text
Fencing Details URB-P0003847-000-SP-APPENDIX(2of2)-240719
Very large file (11.3 MB): the original may take a few minutes to open or download. The page text below is quick to read.
0) 4''(e) "3°49 SPECIFICATION SHEETS GOLOURSMART BREEZEWAY GOLORBOND® FENCING
See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalLog in to download the original file
The download may take a few minutes. On mobile data, it is best to wait for Wi-Fi.
Full text of the other 43 pages
Page 2
COLORBOND® COLOURSMART BREEZEWAY PANEL
WIDTHS 2400, 3180; HEIGHTS 1200, 1500, 1800, 2100
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
- Posts & Rails 0.8mm / Infill Sheets 0.35mm
Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
COLORBOND® BREEZEWAY PANELS
2400mm wide Breezeway Panel consists of:
3 x Overlapped Sheets (835mm Wide)
2 x CS Channel Posts
3 x 2400mm CS Rails
3 of 65 x 16 x 2400mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
Posts with 14mm Slat Spacings
3180mm wide Breezeway Panel consists of:
**1800mm High Panel Shown 4 x Overlapped Sheets (835mm Wide)
COLORBOND® COLOURSMART BREEZEWAY GATE
2 x CS Channel Posts
WIDTHS 930, 1720; HEIGHTS 1200, 1500, 1800, 2100
Channel Posts are connected together 3 x 3180mm CS Rails
and sit back to back in post holes to
create the Post system FRONT ELEVATION 3 of 65 x 16 x 3600mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
Posts with 14mm Slat Spacings
COLORBOND® BREEZEWAY GATES
Single Gates are 930mm Wide:
1 x Infill Sheets;
BACK TO BACK POST DETAIL 2 x Breezeway Gate Stile;
3 x 830mm CS Rail;
3 of 65 x 16 x 820mm Slats
Double Gates are 1720mm Wide per Leaf:
COLOURSMART POST
2 x Infill Sheets;
PROFILE - 0.8 BMT 2 x Breezeway Gate Stile;
BREEZEWAY ZIG ZAG PROFILE
0.35MM BASE METAL THICKNESS (BMT) 3 x 1620mm CS Rail;
3 of 65 x 16 x 1610mm Slats
Available in 22 Colorbond® Steel Fencing
500 - 600mm
colours, guaranteed to meet AS2728.
POWDER COATED
65 X 16MM BREEZEWAY
POWDER COATED PRE-SLOTTED TITLE: COLOURSMART BREEZEWAY
ALUMINIUM SLAT ALUMINIUM POST PANEL & GATE SPECIFICATIONS
14MM SPACINGS
CONTACT: [email protected]
250mm COLOURSMART RAIL
IN GROUND POST DETAIL BREEZEWAY PANEL INFILL PROFILE - 0.8 BMT oxworks.com.au 1300 336 237
Page 3
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
- Posts & Rails 0.8mm / Infill Sheets 0.35mm
Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
COLORBOND® BREEZEWAY PANELS
2400mm wide Breezeway Panel consists of:
3 x Overlapped Sheets (835mm Wide)
2 x CS Channel Posts
3 x 2400mm CS Rails
3 of 65 x 16 x 2400mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
Posts with 14mm Slat Spacings
3180mm wide Breezeway Panel consists of:
4 x Overlapped Sheets (835mm Wide)
2 x CS Channel Posts
3 x 3180mm CS Rails
3 of 65 x 16 x 3600mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
Posts with 14mm Slat Spacings
COLORBOND® BREEZEWAY GATES
Single Gates are 930mm Wide:
1 x Infill Sheets;
2 x Breezeway Gate Stile;
3 x 830mm CS Rail;
3 of 65 x 16 x 820mm Slats
Double Gates are 1720mm Wide per Leaf:
2 x Infill Sheets;
2 x Breezeway Gate Stile;
3 x 1620mm CS Rail;
3 of 65 x 16 x 1610mm Slats
Available in 22 Colorbond® Steel Fencing
colours, guaranteed to meet AS2728.
TITLE: COLOURSMART BREEZEWAY
TYPICAL CONFIGURATION
(2400 X 1800MM PANEL SHOWN)
COLOURSMART BREEZEWAY PANEL CONTACT: [email protected]
(2400 x 1800mm SHOWN)
oxworks.com.au 1300 336 237
Page 4
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
- Posts & Rails 0.8mm / Infill Sheets 0.35mm
Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
COLORBOND® BREEZEWAY PANELS
2400mm wide Breezeway Panel consists of:
3 x Overlapped Sheets (835mm Wide)
2 x CS Channel Posts
3 x 2400mm CS Rails
BREEZEWAY SLAT SETUP TOP RAIL POST SETUP 3 of 65 x 16 x 2400mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
Posts with 14mm Slat Spacings
3180mm wide Breezeway Panel consists of:
4 x Overlapped Sheets (835mm Wide)
2 x CS Channel Posts
3 x 3180mm CS Rails
3 of 65 x 16 x 3600mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
Posts with 14mm Slat Spacings
COLORBOND® BREEZEWAY GATES
Single Gates are 930mm Wide:
CHANNEL
POST 1 x Infill Sheets;
2 x Breezeway Gate Stile;
3 x 830mm CS Rail;
3 of 65 x 16 x 820mm Slats
Double Gates are 1720mm Wide per Leaf:
IN-FILL 2 x Infill Sheets;
SHEET 2 x Breezeway Gate Stile;
3 x 1620mm CS Rail;
3 of 65 x 16 x 1610mm Slats
Available in 22 Colorbond® Steel Fencing
colours, guaranteed to meet AS2728.
IN-FILL SET-UP
RAIL
BOTTOM RAIL & POST SET-UP TITLE: COLOURSMART BREEZEWAY
UNASSEMBLED CONFIGURATION
CONTACT: [email protected]
oxworks.com.au 1300 336 237
Page 5
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
STILE INSERTS INTO - Posts & Rails 0.8mm / Infill Sheets 0.35mm
COLOURSMART RAIL Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
COLORBOND® BREEZEWAY PANELS
2400mm wide Breezeway Panel consists of:
3 x Overlapped Sheets (835mm Wide)
2 x CS Channel Posts
3 x 2400mm CS Rails
3 of 65 x 16 x 2400mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
TOP GATE STILE SET-UP Posts with 14mm Slat Spacings
INFILL SHEET SLIDES INTO 3180mm wide Breezeway Panel consists of:
SIDE C CHANNEL 4 x Overlapped Sheets (835mm Wide)
2 x CS Channel Posts
3 x 3180mm CS Rails
3 of 65 x 16 x 3600mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
COLOURSMART Posts with 14mm Slat Spacings
GATE STILE
COLORBOND® BREEZEWAY GATES
Single Gates are 930mm Wide:
1 x Infill Sheets;
2 x Breezeway Gate Stile;
3 x 830mm CS Rail;
3 of 65 x 16 x 820mm Slats
Double Gates are 1720mm Wide per Leaf:
2 x Infill Sheets;
2 x Breezeway Gate Stile;
3 x 1620mm CS Rail;
3 of 65 x 16 x 1610mm Slats
Available in 22 Colorbond® Steel Fencing
colours, guaranteed to meet AS2728.
TITLE: COLOURSMART BREEZEWAY
SINGLE GATE UNASSEMBLED
CONTACT: [email protected]
BOTTOM GATE STILE SET-UP COLOURSMART BREEZEWAY
SINGLE GATE oxworks.com.au 1300 336 237
Page 6
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
- Posts & Rails 0.8mm / Infill Sheets 0.35mm
Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
STILE INSERTS INTO COLORBOND® BREEZEWAY PANELS
COLOURSMART RAIL 2400mm wide Breezeway Panel consists of:
3 x Overlapped Sheets (835mm Wide)
2 x CS Channel Posts
3 x 2400mm CS Rails
TOP GATE STILE SET-UP 3 of 65 x 16 x 2400mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
Posts with 14mm Slat Spacings
3180mm wide Breezeway Panel consists of:
4 x Overlapped Sheets (835mm Wide)
2 x CS Channel Posts
3 x 3180mm CS Rails
3 of 65 x 16 x 3600mm Slats (Cut on site)
2 of Pre-Slotted 50 x 50 x 250mm Breezeway
Posts with 14mm Slat Spacings
COLORBOND® BREEZEWAY GATES
INFILL SHEET SLIDES INTO COLOURSMART
GATE STILE Single Gates are 930mm Wide:
SIDE C CHANNEL
1 x Infill Sheets;
2 x Breezeway Gate Stile;
3 x 830mm CS Rail;
3 of 65 x 16 x 820mm Slats
Double Gates are 1720mm Wide per Leaf:
2 x Infill Sheets;
2 x Breezeway Gate Stile;
3 x 1620mm CS Rail;
3 of 65 x 16 x 1610mm Slats
Available in 22 Colorbond® Steel Fencing
colours, guaranteed to meet AS2728.
TITLE: COLOURSMART BREEZEWAY
DOUBLE GATE UNASSEMBLED
CONTACT: [email protected]
COLOURSMART BREEZEWAY
BOTTOM GATE STILE SET-UP DOUBLE GATE oxworks.com.au 1300 336 237
Page 7
STANDARD COLOUR RANGE - IN STOCK
EW
N
FENCING REFRESH
SURFMIST® SM DOMAIN® DO PAPERBARK® PA EVENING HAZE® EH SHALE GREY® SG
Frost Classic Cream Terrace Summershade Snow Gum COLORBOND® FENCING
Off White Primrose Merino Mossvale Sands Gull Grey COLOUR NAMES & ALIASES
STANDARDS
EW
EW
N
N
• AS1397
Formability & Structural Grades of Steel:
- Posts & Rails 0.8mm
Base Metal Thickness (BMT)
DUNE® DU RIVERSAND® RI PALE EUCALYPT® PE WILDERNESS® WN JASPER® JA - Infill Sheets 0.35mm BMT
Seedpod Meadow Willow Plateau
Grey Birch Mist Green Rivergum Green • AS2728
Coated Mass & Paint Film Thickness
EW
EW
EW
AVAILABILITY
N
N
N
• All colours available IN STOCK at all Stores
• New Colours Available from Feb 2016
BASALT® BA IRONSTONE® IR WOODLAND GREY® WG MONUMENT® MO
NOTE: As printers, monitors and phone
Dark Ash Grey Ridge Shadow screens can differ in the way they display
Slate Grey colours, these colour swatches should be
used as an indicative guide only.
EXTENDED COLOUR RANGE - IN STOCK
EW
EW
N
N
WALLABY® WA WINDSPRAY® WS DEEP OCEAN® DE MANOR RED® MR NIGHT SKY® BL
Haze Bluestone Red Oak Eclipse
Armour Grey Mountain Blue Heritage Red Black Posts & Rails Only
TITLE: COLORBOND® STEEL FENCING
COLOUR RANGE
CONTACT: [email protected]
BUSHLAND® BU COTTAGE GREEN® CG HARVEST® HA ESTATE® ES HEDGE® HE
Tea Tree Evergreen Wheat Ironbark While Stocks Last Plantation While Stocks Last
oxworks.com.au 1300 336 237
Caulfield Green
Page 8
0) 4''(e) "3°49 SPECIFICATION SHEETS COLOURSMART TRIMLINE GOLORBOND® FENCING
Page 9
COLORBOND® COLOURSMART TRIMLINE PANEL
WIDTHS 2400, 3180; HEIGHTS 1200, 1500, 1800, 2100
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
Posts & Rails 0.8mm / Infill Sheets 0.35mm
Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
COLORBOND® TRIMLINE PANELS
2400mm wide Coloursmart Panel consists of:
3 x TL Infill Sheets (835mm Wide
Overlapped)
2 x CS Channel Posts
2 x 2400mm CS Rails
12 of 10-16*16 Tek Screws per Panel
(Sold Seperately)
3180mm wide Coloursmart Panel consists of:
4 x TL Infill Sheets (835mm Wide
COLORBOND® COLOURSMART TRIMLINE GATE **1800mm High Panel Shown Overlapped)
WIDTHS 930, 1720; HEIGHTS 1200, 1500, 1800, 2100 2 x CS Channel Posts
Channel Posts are connected together
and sit back to back in post holes to FRONT ELEVATION 2 x 3180mm CS Rails
create the Post system
16 of 10-16*16 Tek Screws per Panel
(Sold Seperately)
COLORBOND® TRIMLINE GATES
• Single Gates (930mm Wide):
1 x TL Infill Sheets; 2 x CS Gate Stile;
BACK TO BACK POST DETAIL 2 x 830mm CS Rail;
16 of 10-16*16 Tek Screws per Single Gate
(Sold Seperately)
• Double Gates (1720mm Wide per Leaf):
COLOURSMART POST 2 x TL Infill Sheets; 2 x CS Gate Stile;
PROFILE - 0.8 BMT 2 x 1620mm CS Rail;
16 of 10-16*16 Tek Screws per Double Gate
Leaf (Sold Seperately)
Available in 22 Colorbond® Steel Fencing
500 - 600mm
colours, guaranteed to meet AS2728.
COLOURSMART TRIMLINE PANEL PROFILE
0.35MM BASE METAL THICKNESS (BMT) TITLE:
COLOURSMART TRIMLINE
PANEL AND GATE
SPECIFICATIONS
CONTACT: [email protected]
250mm COLOURSMART RAIL
PROFILE - 0.8 BMT oxworks.com.au 1300 336 237
IN GROUND POST DETAIL
Page 10
COLOURSMART TRIMLINE PANEL
(2400 x 1800mm SHOWN)
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
Posts & Rails 0.8mm / Infill Sheets 0.35mm
Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
COLORBOND® TRIMLINE PANELS
2400mm wide Coloursmart Panel consists of:
3 x TL Infill Sheets (835mm Wide
Overlapped)
2 x CS Channel Posts
2 x 2400mm CS Rails
12 of 10-16*16 Tek Screws per Panel
(Sold Seperately)
3180mm wide Coloursmart Panel consists of:
4 x TL Infill Sheets (835mm Wide
Overlapped)
2 x CS Channel Posts
2 x 3180mm CS Rails
16 of 10-16*16 Tek Screws per Panel
(Sold Seperately)
COLORBOND® TRIMLINE GATES
• Single Gates (930mm Wide):
1 x TL Infill Sheets; 2 x CS Gate Stile;
2 x 830mm CS Rail;
16 of 10-16*16 Tek Screws per Single Gate
(Sold Seperately)
• Double Gates (1720mm Wide per Leaf):
2 x TL Infill Sheets; 2 x CS Gate Stile;
2 x 1620mm CS Rail;
16 of 10-16*16 Tek Screws per Double Gate
Leaf (Sold Seperately)
Available in 22 Colorbond® Steel Fencing
colours, guaranteed to meet AS2728.
TITLE: COLOURSMART TRIMLINE
TYPICAL CONFIGURATION
(2385 X 1800MM PANEL SHOWN)
CONTACT: [email protected]
oxworks.com.au 1300 336 237
Page 11
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
Posts & Rails 0.8mm / Infill Sheets 0.35mm
Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
COLORBOND® TRIMLINE PANELS
2400mm wide Coloursmart Panel consists of:
3 x TL Infill Sheets (835mm Wide
Overlapped)
2 x CS Channel Posts
IN-FILL 2 x 2400mm CS Rails
CHANNEL SHEET
12 of 10-16*16 Tek Screws per Panel
POST (Sold Seperately)
3180mm wide Coloursmart Panel consists of:
4 x TL Infill Sheets (835mm Wide
Overlapped)
IN-FILL SET-UP 2 x CS Channel Posts
2 x 3180mm CS Rails
16 of 10-16*16 Tek Screws per Panel
(Sold Seperately)
COLORBOND® TRIMLINE GATES
• Single Gates (930mm Wide):
1 x TL Infill Sheets; 2 x CS Gate Stile;
2 x 830mm CS Rail;
RAIL
16 of 10-16*16 Tek Screws per Single Gate
(Sold Seperately)
BOTTOM RAIL & POST SET-UP
• Double Gates (1720mm Wide per Leaf):
2 x TL Infill Sheets; 2 x CS Gate Stile;
2 x 1620mm CS Rail;
16 of 10-16*16 Tek Screws per Double Gate
Leaf (Sold Seperately)
Available in 22 Colorbond® Steel Fencing
colours, guaranteed to meet AS2728.
TITLE:
COLOURSMART TRIMLINE
PANEL UNASSEMBLED
CONFIGURATION
CONTACT: [email protected]
oxworks.com.au 1300 336 237
Page 12
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
Posts & Rails 0.8mm / Infill Sheets 0.35mm
STILE INSERTS INTO Base Metal Thickness (BMT)
COLOURSMART RAIL • AS2728
Coated Mass & Paint Film Thickness
COLORBOND® TRIMLINE PANELS
2400mm wide Coloursmart Panel consists of:
3 x TL Infill Sheets (835mm Wide
Overlapped)
2 x CS Channel Posts
2 x 2400mm CS Rails
12 of 10-16*16 Tek Screws per Panel
(Sold Seperately)
TOP GATE STILE SET-UP
3180mm wide Coloursmart Panel consists of:
4 x TL Infill Sheets (835mm Wide
Overlapped)
INFILL SHEET SLIDES INTO 2 x CS Channel Posts
SIDE C CHANNEL 2 x 3180mm CS Rails
16 of 10-16*16 Tek Screws per Panel
(Sold Seperately)
COLORBOND® TRIMLINE GATES
• Single Gates (930mm Wide):
COLOURSMART 1 x TL Infill Sheets; 2 x CS Gate Stile;
2 x 830mm CS Rail;
GATE STILE
16 of 10-16*16 Tek Screws per Single Gate
(Sold Seperately)
• Double Gates (1720mm Wide per Leaf):
2 x TL Infill Sheets; 2 x CS Gate Stile;
2 x 1620mm CS Rail;
16 of 10-16*16 Tek Screws per Double Gate
Leaf (Sold Seperately)
Available in 22 Colorbond® Steel Fencing
colours, guaranteed to meet AS2728.
TITLE:
COLOURSMART TRIMLINE
SINGLE GATE UNASSEMBLED
CONFIGURATION
CONTACT: [email protected]
BOTTOM GATE STILE SET-UP COLOURSMART TRIMLINE
SINGLE GATE oxworks.com.au 1300 336 237
Page 13
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
Posts & Rails 0.8mm / Infill Sheets 0.35mm
Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
COLORBOND® TRIMLINE PANELS
2400mm wide Coloursmart Panel consists of:
3 x TL Infill Sheets (835mm Wide
Overlapped)
2 x CS Channel Posts
TOP GATE STILE SET-UP 2 x 2400mm CS Rails
12 of 10-16*16 Tek Screws per Panel
(Sold Seperately)
3180mm wide Coloursmart Panel consists of:
4 x TL Infill Sheets (835mm Wide
Overlapped)
2 x CS Channel Posts
2 x 3180mm CS Rails
16 of 10-16*16 Tek Screws per Panel
(Sold Seperately)
INFILL SHEET SLIDES INTO COLORBOND® TRIMLINE GATES
SIDE C CHANNEL
• Single Gates (930mm Wide):
COLOURSMART 1 x TL Infill Sheets; 2 x CS Gate Stile;
GATE STILE 2 x 830mm CS Rail;
16 of 10-16*16 Tek Screws per Single Gate
(Sold Seperately)
• Double Gates (1720mm Wide per Leaf):
2 x TL Infill Sheets; 2 x CS Gate Stile;
2 x 1620mm CS Rail;
16 of 10-16*16 Tek Screws per Double Gate
Leaf (Sold Seperately)
Available in 22 Colorbond® Steel Fencing
colours, guaranteed to meet AS2728.
TITLE:
COLOURSMART TRIMLINE
DOUBLE GATE UNASSEMBLED
CONFIGURATION
STILE INSERTS INTO CONTACT: [email protected]
COLOURSMART RAIL
COLOURSMART TRIMLINE
BOTTOM GATE STILE SET-UP DOUBLE GATE oxworks.com.au 1300 336 237
Page 14
STANDARD COLOUR RANGE - IN STOCK
EW
N
FENCING REFRESH
SURFMIST® SM DOMAIN® DO PAPERBARK® PA EVENING HAZE® EH SHALE GREY® SG
Frost Classic Cream Terrace Summershade Snow Gum COLORBOND® FENCING
Off White Primrose Merino Mossvale Sands Gull Grey COLOUR NAMES & ALIASES
STANDARDS
EW
EW
N
N
• AS1397
Formability & Structural Grades of Steel:
- Posts & Rails 0.8mm
Base Metal Thickness (BMT)
DUNE® DU RIVERSAND® RI PALE EUCALYPT® PE WILDERNESS® WN JASPER® JA - Infill Sheets 0.35mm BMT
Seedpod Meadow Willow Plateau
Grey Birch Mist Green Rivergum Green • AS2728
Coated Mass & Paint Film Thickness
EW
EW
EW
AVAILABILITY
N
N
N
• All colours available IN STOCK at all Stores
• New Colours Available from Feb 2016
BASALT® BA IRONSTONE® IR WOODLAND GREY® WG MONUMENT® MO
NOTE: As printers, monitors and phone
Dark Ash Grey Ridge Shadow screens can differ in the way they display
Slate Grey colours, these colour swatches should be
used as an indicative guide only.
EXTENDED COLOUR RANGE - IN STOCK
EW
EW
N
N
WALLABY® WA WINDSPRAY® WS DEEP OCEAN® DE MANOR RED® MR NIGHT SKY® BL
Haze Bluestone Red Oak Eclipse
Armour Grey Mountain Blue Heritage Red Black Posts & Rails Only
TITLE: COLORBOND® STEEL FENCING
COLOUR RANGE
CONTACT: [email protected]
BUSHLAND® BU COTTAGE GREEN® CG HARVEST® HA ESTATE® ES HEDGE® HE
Tea Tree Evergreen Wheat Ironbark While Stocks Last Plantation While Stocks Last
oxworks.com.au 1300 336 237
Caulfield Green
Page 15
STANDARDS
• AS1397 Formability & Structural Grades of
Steel:
- Posts & Rails 0.8mm / Infill Sheets 0.35mm
Base Metal Thickness (BMT)
• AS2728
Coated Mass & Paint Film Thickness
POST EXTENSION
• 0.55mm Galvanised Steel Section
• 50 x 500mm
• 15mm Folded Opposing wings
• Allows up to 300mm of extension of channel
posts
• Fix using 2 x 10-16*16 Tek Screws
200mm
(Sold Seperately)
500 - 600mm
500mm
300mm
15mm
50mm
TITLE:
COLORBOND® COLOURSMART
POST EXTENSION
SPECIFICATIONS
15mm
BACK TO BACK POST EXTENSION DETAIL CONTACT: [email protected]
oxworks.com.au 1300 336 237
Page 16
DEK BOLLARD SPECIFICATIONS
Design - Street + Garden , 2016 Designing Shared Value
Image Credit: Regan Crook
Simple yet effective, the Dek bollard address Each design developed by S+G has been
all the needs of a modern bollard in one created to become an integral part of all the
simple and modern and cost effective design. diverse elements that distinguish a particular
place or time. Historical and contemporary
references along with current and long term
aspirations for what a place is and may be are
adopted as the ways to find a functional and
complementary design solution.
Designed and Manufactured in Australia. www.streetandgarden.com
Material Options Warranty and Care
○○ Grade 304 Stainless Steel Remove grime with damp cloth. Apply mild
○○ Grade 316 Stainless Steel automotive polish to maintain original
appearance.
Finish Options
Frame • 12 month finish warranty on PC
○○ Bead Blasted Stainless Steel • 5 year structure warranty
○○ Brushed Stainless Steel (Standard)
See warranty agreement for further details.
Variations
○○ Flat Top - Removable (DEK6-F-R)
○○ Flat Top - Fixed (DEK6-F-F)
○○ Dome Top - Removable (DEK6-D-R)
○○ Dome Top - Fixed (DEK6-D-F)
Installation
Fixed
• 3 x M10 masonry anchors with Security
nuts (by others)
© Street + Garden 2015
Removable
• Cast in rag bolt cage with fixing bolt
(supplied by S+G)
Page 17
SL0Z Uapued + 122415 @
@ STREET
+
(OW) Garden
Fixed
Product Code - DEK6-F-F
Fixed
Product Code - DEK6-D-F
225 (9°)
=
te
ee
Fete
oS
| .
225 (9°)
1000 (3°4")
DE TE AAU
Scale ~ 1:20 (Ad) Removable
MM IFT INCH")
Da not scale from drawings. Product Code - DEK6-D-R
Seale - 1:20 IAA)
MM {FT INCH")
Da not scale from drawings.
225 9")
1000 (3°4")
Seale - 1:20 [A4)
MM FT INCH")
Do not-scale from drawings:
Page 18
SL0Z Uapued + 122415 @ STREET + (OW) Garden Bollard locked down to ground surface with central locking pin [booker rod and bolt) JS a sa Ballard fitted to in-ground socket assembly with guide bracket and pins Rag bolt assembly and bollard fixing plate installed flush with ground surface Pavement level Typical Removable Bollard Installation Elevation View MM (FTINCH") Do not scale from drawings. UREN — —@———// — Installation and Fixings (BY OTHERS) Slab and Footing details to OTHERS specifications Applies to all surface mounted bollards Typical Bollard Installation | | | Use furniture to mark and drill fixing locations Detail View MM (FT'INCH") Do not scale from drawings.
Page 19
BEFORE YOU START
• To ensure that the installation and erection of your Stratco Handi-Mate™ Shed proceeds smoothly you should confirm that all
the components and materials listed on the delivery documentation and in this installation guide have been supplied. Details
for ordering individual components can be found in the “Component Index” section at the end of this document.
• Carefully read this installation guide to familiarise yourself with all the steps involved and ensure that you have the correct tools
and equipment for the job.
• There are different types and colours of screws. Ensure that the right type and colour screw is being used at each location.
• Use heavy gloves when handling steel sheeting and flashings and never attempt to install a shed in windy conditions.
• It is important that you contact your local government authority to determine if building approval is required.
• Stability and performance of the shed relies on the door being closed during high wind events.
• It is essential to clear and level the site prior to assembling your Stratco Handi-Mate™ Shed.
• Do not traverse the roof of the Handi-Mate™.
• The installer is responsible for ensuring the slab or concrete pads are sufficient to support the shed and sustain wind loading.
Do not directly anchor your shed to pavers. All Stratco Handi-Mate™ Sheds must be securely bolted to a permanent concrete
base with sufficient masonry anchors as specified in Figure 6.0 to prevent wind uplift.
Option 1 - Before building the shed, pour a base that is larger than the area by at least 200mm in each direction. The
base should be poured so the concrete outside the shed floor area slopes away from the shed to help prevent water from
entering the shed.
Option 2 - Substantial concrete pads may be used at each anchor location as an alternative to a complete concrete floor.
It is recommended pads are minimum Ø250mm x 400mm deep, embedded into a firm natural soil base.
• Where necessary, components are marked with a coloured sticker as to easily differentiate one from another. Components are
referenced throughout the installation guide by their colour. For example, Panel (Short) is marked with a red sticker.
SHED WINDOWS (OPTIONAL)
Stratco Shed Windows are available as an optional add-on, available in both Louvre and Sliding variations. Handi-Mate Windows
should be purchased along side the Handi-Mate Shed and installed during the Handi-Mate Shed assembly. Refer to the “Window
Installation” section if installing a Stratco Window, or visit your local Stratco store for more information.
HANDI-MATE™ HM6 HINGED DOOR SHED
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
Page 20
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
TOOLS REQUIRED
Rivet Gun Power Drill PH2 Phillips Head Bit 3/16 Hex Head Bit Adjustable Spanner 3.5mm Bit (Supplied)
(Supplied) (Supplied) 12mm Bit
10mm Masonry Bit
Gloves Safety Glasses Step Ladder 2 x Trestles Permanent Marker Tape Measure
HANDI-MATE™ DIMENSIONS
2.91
2.91 1.47
1.47
2.00
2.00
2.85
2.85 1.45
1.45
HANDI-MATE™ SHED WINDOWS
Stratco Handi-Mate Shed Windows are available as an optional add-on. For HM6 size Handi-Mates, the Window can be
installed to the front or rear wall. Handi-Mate Windows should be installed during the Handi-Mate Shed assembly.
Refer to the “Window Installation” section at the end of this document if installing a Stratco Window, or visit a Stratco store for
more information.
Page 21
COMPONENTS
Door Door Jamb Wall Wall Ridge Cap Ridge Beam
x1 x1 Channel Channel x2 x1
x 12 Joiner
x4
L/H Barge Cap R/H Barge Cap Door Shroud Door Handle Door Tongue Corner Hold Down
x2 x2 x1 x1 x1 Bracket Lug
x8 x8
M8x47 Masonry Coloured Rivet 10x16 Wafer- Head
Anchor x 35 Screw
x 12 x3
10x16 Hex-Head 10x16 Hex-Head 10x25 Hex-Head
Screw Coloured Screw Coloured Screw
x 200 (with neo washer) (with neo washer)
x 75 x 22
Page 22
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
COMPONENTS
Split Wall Sheet Corner Wall Sheet Wall Sheet Roof Sheet
x1 x4 x6 x4
10x16mm Hex-Head Screw
Wall Channel
Fasten through Fasten middle
pilot holes first Screws secondly
ASSEMBLY HANDY HINTS When assembling the Wall and Door Sheets, lay the sheets
down on trestles / blocks (Figure 1.1). This will make assembly
The ‘Sheet Crest’, as referenced throughout this guide, refers
easier and reduce the risk of damage to components.
to the curved top faces of the sheet.
Sheet Crest
REAR WALL ASSEMBLY Trestles / Blocks
FIGURE 1.0 FIGURE 1.1
Page 23
(Optional) Drainage holes can be drilled to help trapped water flow out of the bottom Wall Channels. After assembling the
Walls, drill 6mm holes spaced approximately 350mm apart through the bottom Wall Channels of each Wall. Ensure holes are
located in-between Sheet crests. Ensure metal filings are removed from the channels as to prevent rust spots from forming.
Drain Hole
350
mm
Wall Channel
FIGURE 1.2
WALL CHANNEL ASSEMBLY
Slide two Wall Channels into a Wall Channel Joiner. Ensure the six middle pre-punched holes of the Wall Channel Joiner and
Wall Channels line up. Fasten four 10x16 Hex-Head Screws through the four middle pilot holes of the Wall Channel Joiner and
into the Wall Channels (Figure 2.0).
Assemble three more Wall Channel Assemblies in the same manner so that there are four Wall Channel Assemblies.
Wall Channel
10x16 Hex-Head Screw
Wall Channel Joiner
Wall Channels fit
into Wall Channel Joiner
Wall Channel
FIGURE 2.0
Page 24
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
REAR WALL ASSEMBLY
Stratco Handi-Mate Windows
Refer to the “Window Installation” section at the end of this
document if installing a Stratco Window, or visit a Stratco
store for more information.
Wall Sheet
Wall Channel Assembly
Corner Wall Sheet
Wall Sheet
Wall Channel Assembly Wall Sheet
FIGURE 3.0
Using Trestles or Blocks to support the sheets, lay the Corner Wall Sheet down first. Then lay down the three Wall Sheets. Pay
attention to the ‘overlap’ and ‘underlap’ lapping details (Figure 3.1).
Sheet ‘Overlap’
Sheet ‘Underlap’
Wall Sheet
Wall Sheet
Wall Sheet
Corner Wall Sheet
FIGURE 3.1
1. Fit the Wall Channel Assembly over the lapped Wall Sheets. The end of the Wall Channel should fit up against the end of
the Corner Wall Sheet (Figure 3.2).
2. Wall Channels have three pilot holes in each end. Fasten through the third pilot hole of both Wall Channel ends and into the
Wall Sheet crests. Fasten through the Wall Channel Assemblies and into every third Wall Sheet crest using ten 10x16 Hex-Head
Screws in each Wall Channel Assembly (Figure 3.2).
Page 25
10x16 Hex-Head Screw
Wall Sheet
Corner Wall Sheet
Wall Channel Assembly
Wall Channel Assembly
Wall Sheet
Wall Sheet
1. 2. 2.
FIGURE 3.2
SIDE WALL ASSEMBLY
10x16 Hex-Head Screw
Wall Channel
Corner Wall Sheet
Wall Sheet
Wall Channel
FIGURE 4.0
Page 26
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
Using Trestles or Blocks to support the Sheets, lay down the Corner Wall Sheet and Wall Sheet (Figure 4.1).
Sheet ‘Overlap’
Sheet ‘Underlap’
Wall Sheet
Corner Wall Sheet
FIGURE 4.1
1. Fit the Wall Channel over the lapped Wall Sheets. The end of the Wall Channel should fit up against the end of the Corner
Wall Sheet (Figure 3.2).
2. Fasten through the third pilot hole of both Wall Channel ends and into the Wall Sheet crests. Fasten through the Wall
Channels and into every third Wall Sheet crest using four 10x16 Hex-Head Screws in each Wall Channel (Figure 3.2).
10x16 Hex-Head Screw
Wall Channel
Corner Wall Sheet
Wall Sheet
Wall Channel
1. 2. 2.
FIGURE 3.2
SECOND SIDE WALL ASSEMBLY
Repeat steps in Figures 3.0 - 3.2 to make a second Side Wall Assembly.
Page 27
FRONT WALL ASSEMBLY
Split Wall Sheet
Wall Channel Assembly
Wall Sheet
Corner Wall Sheet
Door
Wall Channel Assembly
Door Jamb
FIGURE 4.0
Lay out a Corner Wall Sheet, Wall Sheet and Split Wall Sheet onto trestles/blocks. Fit the Door over the Split Wall Sheet and then
fit the Door Jamb up against the Door. (Figure 4.1).
Split Wall Sheet
Wall Sheet
Corner Wall Sheet
Door
Door Jamb
Sheet ‘Overlap’
Sheet ‘Underlap’
Split Wall Sheet Door
Wall Sheet
Corner Wall Sheet
FIGURE 4.1
Page 28
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
1. Fit two Wall Channel Assemblies over the lapped Wall Sheets and Door Jambs. The end of the Wall Channels should fit up
against the end of the Corner Wall Sheet (Figure 4.2).
2. Fasten one 10x16 Hex-Head Screw through the third pilot hole of the bottom and top Wall Channels and into the Corner
Wall Sheet crest. Fasten six 10x16 Hex-Head Screws through the bottom and top Wall Channels and into every third Wall Sheet
crest (Figure 4.2).
3. Ensure the edge of the Wall Channels and Door Jamb are in-line. Fasten one 10x16 Hex-Head Screw through the third pilot
hole of the bottom and top Wall Channels and into the Door Jamb (Figure 4.2).
Split Wall Sheet 10x16 Hex-Head Screw
Corner Wall Sheet Wall Channel Assembly
Wall Channel Assembly
Door Jamb
1. 2. 3.
Edge of Wall Channel
and Door Jamb in-line
FIGURE 4.2
Page 29
With the Door open, fit the Door Shroud in-between the Door Jambs. Use the Door Shroud as a guide to set the correct
spacing between the Door Jambs (Figure 4.3).
1. Fasten two 10x16 Hex-Head Screws through both Wall Channels and into the Door Jamb. Close the Door and ensure an
approximate 10mm gap between the edge of the Door and end Door Jamb (Figure 4.3).
10x16 Hex-Head Screw
Door Shroud
Door Jamb Door Jamb
Wall Channel Assembly
1.
10mm
Bottom View
FIGURE 4.3
Page 30
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
JOINING WALL ASSEMBLIES
The wall assemblies can now be joined together. Fit the Corner Wall Sheet of the Front Wall over the Side Wall Sheet. Ensure
the Corner Sheet fits inside the Side Wall Channels (Figure 5.0).
1. Fit a Corner Bracket over the top Wall Channels. Ensure the pilot holes of the Corner Bracket and Wall Channels line up.
2. Fasten through the Corner Bracket pilot holes and into the top Wall Channels using four 10x16 Hex-Head Screws.
3. Fit a Corner Bracket to the bottom Wall Channels. Fasten through the Corner Bracket pilot holes and into the bottom Wall
Channels using four 10x16 Hex-Head Screws (Figure 5.0).
Front Wall Assembly
Wall Assembly
1. 2. 3.
Wall Channel Wall Channel
Corner Bracket
Corner Bracket
10x16 Hex-Head Screw
Corner Bracket 10x16 Hex-Head Screw
FIGURE 5.0
Page 31
Fit the Remaining Wall Assemblies together with Corner Brackets as per Figure 5.0.
Rear Wall Assembly
Side Wall Assembly
Front Wall Assembly
Side Wall Assembly
FIGURE 5.1
Fasten the Door Handle to the Handle Mount with two 10x16 Wafer-Head Screws. Fit the Door Tongue over the Door Handle
shaft. Ensure the Door Tongue is oriented vertically and the Handle is oriented horizontally. Tighten the Door Tongue screw on
the Door Handle shaft to secure the Door Tongue in place. Lastly, slide the Locking Washer onto the Door Handle shaft and
up against the Door Tongue (Figure 5.2).
Locking Washer
Door Tongue Screw
Door Tongue
Handle Mount
Door Handle
10x16 Wafer-Head Screw
FIGURE 5.2
Page 32
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
Fit the Door Shroud into the Wall Channel (Long). Fasten the Using the Corner Bracket pilot holes as a guide, drill holes in
Door Shroud to the Wall Channel with two 10x16 Hex-Head all four corners with a 10mm masonry drill bit. Secure all four
Screws (Figure 5.3). bottom Corner Brackets to the concrete base with M8x47
Masonry Anchors (Figure 6.1).
10x16 Hex-Head Screw Masonry Anchor
Hold Down Lug
Door Shroud
Wall Channel - Long Hold Down Lug Hold Down Lug
Corner Bracket
FIGURE 6.1
Fit a Hold Down Lug at Hold
the middle
Down Lugof both Long Wall
FIGURE 5.3 Channels. Fasten one 10x16 Hex-Head Screw through each
Hold Down Lug into the Wall Channel and Wall Sheet. Fix
both Hold Down Lugs to the concrete base with M8x47
Masonry Anchors (Figure 6.2).
SHED ANCHORING
Check the walls are square. Check the diagonal
measurements from corner to corner. The diagonal
measurements should be equal for the walls to be square.
Note: Shed anchoring requirements are determined by
the wind zone the Handi-Mate is installed in. Contact a
Stratco store for further information or to determine your
wind zone.
The recommended anchor spacing in Figure 6.0 below, Masonry Anchor
where anchor points are no greater than 900mm apart, Bottom Channel
will satisfy engineering requirements for N1, N2 and N3 10x16 Hex-Head
wind zones. Screw
Hold Down Lug
FIGURE 6.2
‘X’ - Anchor Locations
FIGURE 6.0
Page 33
ROOF ASSEMBLY
L/H Barge Cap
Ridge Cap
Roof Sheet
R/H Barge Cap
R/H Barge Cap
Ridge Beam
L/H Barge Cap
FIGURE 7.0
Use an adjustable spanner to turn up the pans at the ridge end of the Roof Sheets. This will prevent water flowing back under
the sheet (Figure 7.1).
Pan
FIGURE 7.1
Refer to the sheet layout below when installing Roof Sheets (Figure 7.2).
Sheet ‘Overlap’
Sheet ‘Underlap’
Roof Sheet
Sheet ‘Overlap’ towards
Roof Sheet the front of the Shed
FIGURE 7.2
Page 34
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
Fit the Ridge Beam onto the top Wall Channel Assemblies. Ensure 1355mm spacing between the edge of the shed and edge
of the Ridge Beam (Figure 7.3).
1. Align the end of the Ridge Beam with the outer edge of the Wall Channel Assembly. Fasten two 10x16 Hex-Head Screws
through the pilot holes in the Ridge Beam and into the Wall Channel Assembly (Figure 7.3).
2. Fasten two 10x16 Hex-Head Screws through the pilot holes in the Ridge Beam and into the rear Wall Channel Assembly
(Figure 7.3).
Wall Channel Assembly Ridge Beam
10x16 Hex-Head Screw
m
5m
135
1. 2.
Ridge Beam
10x16 Hex-Head Screw
Wall Channel
Assembly
5 mm
83
FIGURE 7.3
Refer to Figure 7.2 for Sheet layout. Lay a Roof Sheet onto the Ridge Beam and Wall Channel, ensuring the overlap end of the
Roof Sheet is facing the front of the shed (Figure 7.4).
1. Ensure the end of the Roof Sheet is in-line with the end of the Ridge Beam. Fasten five 10x16 Hex-Head Screws with Neo
Washers through the pans of the Roof Sheet and into the Ridge Beam (Figure 7.4).
2. Fasten five 10x16 Hex-Head Screws with Neo Washers through the pans of the Roof Sheet and into the Wall Channel
(Figure 7.4).
Install the opposing side Roof Sheet in the same manner.
Page 35
Roof Sheet
10x16 Hex-Head Screw
with Neo Washer
Ridge Beam
Wall Channel
Ridge Beam
1. 2.
FIGURE 7.4
Position the Ridge Cap over the Ridge Beam. The end of the Ridge Cap should line up with the outer face of the Wall Channel
(Figure 7.5).
Fasten the Ridge Cap to the Ridge Beam using two 10x16 Hex-Head Screws with Neo Washers (Figure 7.5).
10x16 Hex-Head Screw
with Neo Washer
Ridge Cap
Ridge Beam
FIGURE 7.5
Page 36
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
Refer to Sheet layout in Figure 7.2. Lay the next Roof Sheet onto the Ridge Beam and Wall Channel, ensuring the overlap end of
the Roof Sheet is facing the front of the shed (Figure 7.6).
1. Ensure the Roof Sheet is hard against the step of the Ridge Beam. Fasten five 10x16 Hex-Head Screws with Neo Washers
through the pans of the Roof Sheet and into the Ridge Beam (Figure 7.6).
2. Fasten five 10x16 Hex-Head Screws with Neo Washers through the pans of the Roof Sheet and into the Wall Channel
(Figure 7.6).
Install the opposing side Roof Sheet in the same manner.
Ridge Beam
Roof Sheet
10x16 Hex-Head Screw
with Neo Washer
Wall Channel
1. 2.
FIGURE 7.6
Page 37
Position the Ridge Cap over the Ridge Beam. The end of the Ridge Cap should line up with the outer face of the Wall Channel
(Figure 7.7).
Fasten the Ridge Cap to the Ridge Beam using three 10x16 Hex-Head Screws with Neo Washers (Figure 7.7).
10x16 Hex-Head Screw
with Neo Washer
Ridge Cap
Ridge Beam
Ridge Cap
Ridge Beam
FIGURE 7.7
Page 38
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
1. Place the L/H Barge Cap over the Roof Sheet at the front of the shed. The front face of the Barge Cap should fit up against
the Roof Sheets (Figure 7.6).
2. The ends of the Barge Cap Should align with the end of the Roof Sheet. Fasten two coloured 10x25 Hex-Head Screws with
Neo Washers through the front face of the Barge Cap and into the Wall Channel Assembly. Fasten two coloured 10x25 Hex-
Head Screws with Neo Washers through the top of the Barge Cap and into the crests of the Roof Sheets (Figure 7.6).
Install the R/H Barge Cap in the same manner on the front right side of the shed. Install the remaining L/H and R/H Barge Caps
to the rear of the shed in the same manner (Figure 7.6).
L/H Barge Cap
Roof Sheet
R/H Barge Cap
R/H Barge Cap
L/H Barge Cap
1. 2.
mm
Coloured 10x25 Hex-Head 220
Screw with Neo Washer
FIGURE 7.6
Page 39
A coloured Rivet should be installed at sheet laps in the Roof Sheets, Rear Wall, Wall Corners and Door Jambs. Drill a 3.5mm
hole through the centre of each sheet lap and install a coloured Rivet (Figure 7.7).
Coloured Rivet
FIGURE 7.7
Water-Proofing the Floor (Optional)
Water may enter the Shed between the bottom Wall Channels and Floor. Water ingress can be mitigated by applying silicone to
the gaps along the Floor. From the inside of the Shed, apply a bead of silicone along the entire perimeter of the Shed, including
along the Corner Brackets and Wall Channel ends. Do not apply silicone to the outside of the Shed as this will not allow water
to flow out and away from the Shed (Figure 7.8).
Silicone Bead
Wall Channel
FIGURE 7.8
SHED MAINTENANCE
It is vital that all metal swarf and filings are removed from the shed as to prevent rust spots from forming. Your Stratco Handi-
MateTM Shed will maintain its good looks for even longer with a simple wash and wipe down. Cleaning should be performed as
often as is required to remove any dirt, salt and pollutants.
Stratco Handi-MateTM Sheds are produced from the highest quality materials and will provide many years of service. Refer to
the ‘Selection Use and Maintenance’ brochure for more information on how to get the best out of your product.
Page 40
HANDI-MATE ™ HM6 HINGED DOOR SHED INSTALLATION GUIDE
WINDOW INSTALLATION Fit the window within the opening. Ensure the top lip of the
window is fitted between the Wall Channel and Wall Sheets.
Stratco Shed Windows are an optional add-on, available in
A minimum of four evenly spaced rivets must be used along
both Louvre and Sliding variations. Installation methods are
each side of the window frame. All fasteners must be fixed
identical for each window type. Windows can be installed to
through the crests of the Wall Sheets (Figure 8.3).
the front or rear wall of the shed.
The Window must be installed during the assembly of the
Rear Wall.
Coloured Rivet
Wall Channel
Wall Channel
Stratco Sliding Window Stratco Louvre Window
Window
FIGURE 8.0
Lay a Wall Sheet on trestles or blocks. Mark and cut 750mm
FIGURE 8.3
from the end of the Wall Sheet (Figure 8.1).
The Window Flashing must be fitted from the inside of the
shed. Fit the short face of the Flashing between the window
and the cut edge of the Wall Sheet. Secure the flashing to
the Wall Sheet with four evenly spaced Rivets. Ensure all
rivets are crest-fixed through to the sheets (Figure 8.4).
mm
750
Rivet
Trestles / Blocks
FIGURE 8.1 Window Flashing
Assemble the Wall Assembly as per the “Front/ Rear Wall Assembly”
section of the install guide using below sheet layout (Figure 8.2).
FIGURE 8.2 FIGURE 8.4
Page 41
COMPONENT INDEX
PROFILE DESCRIPTION PRODUCT CODE
Door Handle HMTH
Door Handle Tongue HMDTHDR
Corner Bracket HMCB
Door Shroud HMDSHDRBO
Wall Channel - 1400mm HMWC1400
Wall Channel Joiner HMWCJ
Barge Cap - Left Hand Side HMBCHDRL
Barge Cap - Right Hand Side HMBCHDRR
Ridge Cap HMRC
Ridge Beam HMRB
Door Jamb HMDJHDC
Complete Door & Jamb Assembly HDJAHDC
Roof Sheet SSPHMRS
Split Wall Sheet SSPHMSW
Corner Wall Sheet SSPHMWSCNR
Wall Sheet SSPHMWS
Hold Down Lug HMHL
Masonry Anchor MAA847
Rivet RIV4-3
22mm Wafer Head Screw WTK1022
16mm Self-Drilling Screw TEKNNW1016
16mm Self-Drilling Screw Neo Washer TEK1016
25mm Self-Drilling Screw Neo Washer TEK1025
« SCAN THIS QR CODE TO FIND A STRATCO NEAR YOU
1300 155 155
stratco.com.au
All brands and logos/images accompanied by ® or ™ are trade marks of Stratco (Australia) Pty Limited. ® Copyright July 2023
I
Page 42
STANDARD PRODUCT METROSEAT Product Description: The Metro Range of outdoor seating The Metro seat is a robust and elegant unit manufactured from marine grade aluminium with stainless steel fix- ings. The modular design allows up to 4 metres in continuous FSC 100% hardwood and up to 6 metres in clear anodised extruded aluminium slats. Options include multiple or single arm rests and edge guards for deterring skateboarders. Various mounting options are available. Should you require special modifications to suit your specification, please do not hesitate to contact us. P: 1300 782 101 W: townandpark.com.au E: [email protected] Copyright Stoddart Pty Ltd. All rights reserved.
Page 43
METROSEAT
Models: Construction:
Code: SPTP.SSD.vv.ww.xxx.yyyy.zz • Marine grade aluminium cast legs, end
frames and armrests
SPTP = Stoddart Product - Town and Park • 316 stainless steel fasteners
SSD = Metro Seat • Hardwood timber slats or extruded
aluminium
vv T2 = Select Grade Hardwood Slats • Timber coated with high quality timber oil
T3 = FSC 100 % Hardwood Slats or 25um clear anodised aluminium
A = Aluminium Slats
Finishes:
ww SP = Surface Post • Powder Coated aluminium
SS = Sub Surface
LF = Leg Foot
PM = Plinth Mount
Example Specification Text:
xxx ARx = x no. of arm rests
EGx = x no. of anti skate edge guard Model Code:
SPTP.SSD.T3.SP.AR2.2000
yyyy 2000 = 2000mm long (STD)
*Various Lengths available to suit Town and Park Metro with FSC 100% hard-
specification wood slats coated with high quality outdoor
decking oil. The Surface Post Mount, end frame
zz PC = Powder Coated aluminium and arm rests to be manufactured from marine
grade aluminium casting. The seat is 2000mm
Options: Engraving & Paint Fill long and 1953mm between the fastening
Memorial Plaque points.
Customers Logo
e.g.: for specification and ordering quote
Town and Park model: SPTP.SSD.T3.SP.
AR2.2000
Install Details:
All measurements in millimetres
P: 1300 782 101
W: townandpark.com.au
E: [email protected]
Copyright Stoddart Pty Ltd. All rights reserved.
Page 44
uRBIS | URBIS.COM.AU