Council archive · source document
Development Application - Part 2 of 2 - Title Search, ecoaccess Decision, DTMR Conditions, Correspondence & Plans · OPW11/0322
Plans and drawings: the text below has words only, no drawings.
1370
EXTERNAL SECTION A STANDARD SIDE PROFILES
JSP-203 1210 TYPICAL ALL CATWALKS
SCALE 1:100 0
TOP CHORD / HANDRAILS INTERNAL SCALE 1:25
rn
3mm ALUMINIUM PLATE FIXED TO FRAMING AT 250mm
JSP-202 CRS WITH 4mm AL. RIVETS & COVERED WITH
UPRIGHTS & DIAGONALS COMMERCIAL OUTDOOR CARPET. OR 125 X 25mm CCA
3 UPRIGHT
NOTE: BENT END OPTION CAN BE
TREATED & DRESSED F17 HARDWOOD PLANKS FIXED USED ON ALL SIZED CATWALKS
WITH 6 / 50 X 10 GAUGE STAINLESS STEEL SCREWS
Qv1O EACH PLANK.
50 X 4 TUBE TOE RAIL
TO 6mm PLATE TO EACH NOTE: FOR 4kPo LOADING TO CATWALK 0
UPRIGHT USE JSP-006 RHS BOTTOM CHORD / BASE RAILS 0 I_IPRlrHT BENT END
0
* FOR UNRESTRICTED ACCESS (ALL SITUATIONS OTHER
THAN PRIVATE FACILITIES FOR ONE OR 2 BOATS).
125 X 35 F17 CCA TREATED HARDWOOD PLANKS
OR 4mm ALUMINIUM PLATE IS REQUIRED.
OPTIONAL FOR MARINAS
60 X 40 x 2 RHS LONGITUDINALS
WELDED BETWEEN ALL CROSS MEMBERS
L
JSP-202 RHS SERVICES FOR CATWALKS WITH TIMBER DECKING
BRACKET WELDED UNDER CROSS ONLY
BEAMS 0 1800 CRS 3I
MAXIMUM CATWALK LENGTHS
NOTES:
' ALL FRAMING MATERIAL TO BE ALUMINUM LIVE DECK LOAD 1.5 kPo 2kPa 3kPa 4kPo
' ALL ALUMINIUM WELDING IN ACCORDANCE WITH A.S. 1665 3 UPRIGHTS 7.5m 6.5m 6.Om 5.Om
' ALL S.S STEEL WELDING IN ACCORDANCE WITH A.S. 1554
' ALL WELDS SHALL BE 4mm C.F.W. U.N.O. 5 UPRIGHTS 11m 1 O.Om 9m 8.5m 1000 I-- T-=,UP I G H T
' ALL ALUMINIUM SECTIONS TO BE GRADE 6351-T5.
' DIMENSKIN TOLERANCES U.N.O. SR41 BE
7 UPRIGHTS 13m 12.2m 11.5m 10.5m
FABRICATION - t 2.0 MACHINING - UP TO 10mm ±0.1 9 UPRIGHTS 15m 13 , 9m 12 . 5m 11 . 5m EQUAL
> 10 TO 100mm ±0.2 UPRIGHT 965
> 100mm 1 0.5 11 UPRIGHTS 17m 16.Om 14.5m 13.Om SPACING 't .
ALL ANGLES it
' CATWALK TO BE NO LESS THAN 500mm ONTO PONTOON AT MEAN LOW WATER.
' REMOVE ALL SHARP CORNERS, BURRS & WELD SPATTER.
' ANY CHANGES TO BE NOTED AND RETURNED TO DRAWING OFFICE FOR REVISION
0
L
JSP-206 PIANO HINGE TUBES WELDED TO CATWALK END
LENGTH AND SPACING TO SUIT STANDARD PIANOH HINGE
ROLLER & RAMP DETAIL TREAD PLATE RAMP SEE DETAIL SEE STANDARD PiAND HINGE & LAND ANCHOR DRAWINGS
SCALE 1:5
00
4mm TREAD PLATE RAMP 50 X 2 SHS 0 EACH UPRIGHT & AT 1/3 X
ACROSS CATWALK END
STITCH WELDED TO STIFFENERS
(UPRIGHT SPACING), WITH 600 CRS MAX.
OR 400 CRS WITH 3mm OR 4mm PLATE
TYPICAL BASE DETAIL
SCALE 1:100
120 S.S PIN WELDED - --
TO 4mm LOCKING TAB
3
& FIXED WITH M6
6
C.S S.S BOLT
'I
0 X 6 FLAT BAR WELDED TO
65X50X4ANGLE HINGE TUBE & CATWALK END
POSITIONED TO SUIT
700 NYLON ROLLER DECKING HEIGHT
00 EACH SIDE OF CATWALK. 50 X 6 FLAT BAR STIFFENER 50 X 6 FLAT BAR STIFFENERS 5-I
27 CUT OUT BOTTOM OF BASE ACROSS CATWALK 0 400 CRS
RAIL TO ACCOMMODATE PIANO HINGE DETAIL
SCALE 1:5
THE MARINA SPECIALIST CLIENT: fxry loaf PV, Pk-J, P, R--,CX --k TmE: STANDARD CATWALK CONSTRUCTION
ACN 010633119 2 INDUSTRIAL AVE ACN: 051 074 992
TRADING AS LOT L (L) ^4l^fr
7
PL RAMPED END OPTION
THE CALOUNDRA Cardno (04d) Pry Lm
Ph (07) 3369 9822 NUo & A H F ^«(s C
OLD. AUSTRALIA 4551 Level I, 5 Goidner Coe, Won 4064 Fox (07) 3369 9722 DRAWING NO:
/10/07 ^OAD TABLE & NOTES ALTERED PHONE (07)5492 5925
P.O. Bm 388, Toorong 4066. Emo7: cordnc0cordno.comou PROJECT: STANDARD DRAWING SEAS SHOWN 5/9/02 JSP-GW-005
ENG
13105 XTRUSIONS CHANGED JSP FAX (07) 5492 6699 CHECKED: R.P.EQ. DATE.- DRAWN WD DMENSiONS ISSUE
DATE AMENDMENT RED b6 7 .o 01 MA MILLIMETERS C A3
See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalLog in to download the original file
The download may take up to a minute.