Skip to the record
Every meeting, every word.

Council archive · source document

RS-050

of 1

Check the original when the exact wording matters.

Plans and drawings: the text below has words only, no drawings.

Log in to see the plans as drawn

Text sections not matched to the original PDF pages. See original document to check page numbers.

ai            —2                              £8
                                                                                             HEIGHT ABOVE a
                                                                                               OF CHANNEL (
                                Control joint
                                300                                                                                                                                                        1500        1500                      1500
       Kerb invert               min                                                                                                                                                  PT                                                      Garage/
                                                                                                                                                                                                                                              Carport slab
                                         _—re ee = —                                                                                           1500min                Slope may vary
                              [Tv                                                         Road surface               c        1500          refer note 13     900      refer note 12                        4 ink
                              Laz                                                                                   f Tension =               Path zone      _
                                                                                                                     —_—
                                                                                                                                                1 in 40              1 in       20        4 in_&
                                              Reinforced SL72 fabric min                                             ®      \ in 8                                                        1 in 20                 lin 4 |        1500
                                                                                                                     <
                                                                                                                                                                                                                               Roll under     Garage/
                                              Sand blinding layer 50 max                                                                                                                                                                      Carport slab
                            Galvanised/stainless                                          Saw cut all kerbs to            Control joint           Control joint
                            steel dowels 400 long                                         allow clean removal of                                  (If required)
                            R16 @ 450 centres                                             back of kerb and
                                                                                          channel
                                   BREAKOUT TYPE                                                                                                 TYPICAL PROFILE DRIVEWAY ACCESS
                                      SECTION A                                                                                                                  SECTION B
                                     Refer drawing                                                                                                               Refer drawing
                                        RS-049                                                                                                                      RS—049
               NOTE
              |    All appropriate permits must be obtained from relevant council,      specifying crossing type                      13   Path zone width may vary to match existing concrete pathways and verge profiles
                   construction materials   location  levels, surface finishes and dimensions,   prior to any excavation                   Path earthworks adjoining concrete must be well compacted
              2    Alternative materials for construction,  other than reinforced concrete    refer to relevant council               14   Earthworks cut and fill batters from edge of driveway or path to natural surface to be
                   for approval                                                                                                            maximum grade at 1 in 10 and fully turfed prior to council inspection
                   Crossing to be constructed square to the street alignment,       wholly contained within the site                  15   Existing path to be longitudinally transitioned to new driveway at a maximum grade of 1 in 10
                   frontage from invert of channel to property boundary                                                               16   Plain concrete surfaces to be heavy broom finished
                   One access to be constructed per allotment unless otherwise approved by relevant Council                           17   Decorative surfaces are subject to relevant council approval,    where approved,   to have a 5mm
                   To reduce impact on available street parking, consideration is to be given to visitors and                              max depth variation in the finished surface profile.   All finished surfaces of driveways are to
                   neighbouring property s parking needs when selecting a crossing location                                                comply with the requirements of AS/NZS 3661.1 slip resistance of pedestrian surfaces
                   Crossing to be located clear of existing gully pits.   where this cannot be achieved,    the gully pit                  Exposed aggregate finish subject to relevant council approval due to environmental reasons
                   and pipework may be relocated at the property owners expense,          subject to approval of the                  18   Expansion joints to be 10mm thick full depth closed cell cross linked polyethylene foam (85 —
                   relevant council                                                                                                        150 kg/m),   or 8.5mm thick bitumen impregnated compressed granulated corkboard,           installation
                   Crossing to be located clear of all service authority s   fittings, manholes and pits.   Subject to                     to manufacturers    instructions. Seal surface of joint with a suitable polyurethane sealant
                   relevant Council approval,  where this cannot be achieved,    existing service pits are to be                      19   Concrete surface tolerance to be    +5mm
                                                                                                                                                                                    over 3 metre sections
                                                                                                                                                                               -0mm
                   contained within the area of new driveway, pit surface to match approved driveway finished                         20   Concrete to be minimum grade N32 in accordance with AS 1379 and AS 3600
                   levels                                                                                                             21   Concrete construction to comply with the requirements of AS 3600,        concrete code
                   Kerb adaptors and associated roofwater drainage to be located clear of vehicular crossings                         22   Reinforcement fabric to AS 1304,     50 top and edge cover,    lap fabric 250
                   Council will not relocate traffic islands or provide breaks in traffic islands to allow driveway                   23   Control joints are to be sealed with a low modulus self priming sealant to the manufacturers
                   access                                                                                                                  specification. refer RS—065
              10   For water sensitive urban design verges,    the vehicular crossing is subject to relevant council                  24   Formwork and reinforcement shall be in place and inspected and approved by the relevant
                   design and approval                                                                                                     council prior to placement of concrete
              11   **Driveways must achieve a high point of 250mm above invert of kerb to ensure stormwater is                        25   Maintenance of the crossings are the responsibility of the property owner
                   contained within the road reserve as per requirement of Q.U.D.M.       (Queensland Urban Drainage                  26   Drawing to be read in conjunction with RS—049
                   manual).  This constraint may be varied upon the approval of the relevant Council                                  27   Cross fall of existing pavement adjacent to the driveway to be checked.       If cross fall exceeds
              12   Under special circumstances Council may approve a rising grade of 1:6 max or falling grade                              5%, relevant Council will decide if driveway needs to be re-designed to ensure satisfactory
                   of 1:20 min     Longitudinal grades along property boundary must allow for free drainage and                            clearance for vehicles
                   pedestrian safety                                                                                                  28   All dimensions are in millimetres unless shown otherwise

                                                                                                These drawings have been developed in consultation between the participating Councils
                                                                                          BEFORE USE, the user shall confirm that the drawing has been adopted by the appropriate Council
 HE} 06/14 | Review                                                                                                                                                                       DRIVEWAYS
re T06710                                                                                 INSTITUTE OF PUBLIC WORKS ENGINEERING AUSTRALASIA                                       RESIDENTIAL DRIVEWAYS                                    RS—050
 B88        be     SSE                                                                                        STANDARD DRAWINGS                                                         PLAN 2 OF 2
     06/09
 Peel bare                     RSS

Used in these records

About this file

File size
105 KB (small file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

RS-050(PDF, 103KB).pdf · 105 KB (small file)

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.