Skip to the record
The gold standard in government transparency.

Council archive · source document

08/1546 - Additional information as requested - Dwelling & retaining Walls [As Published] · 132008.1546

of 32

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

Steel Posts

‘Steel Column

Pad Footing Depth
Refer Page 1

150 (Min)

a
k——|

450 Diameter

Steel Posts

4e N12 Bars
welded to plato

RS Li 250
Pad Footing Depth ae ah 20 er

Rafer Page 1

L

450 Diameter

Design Company

STA CONSULTING ENGINEERS

Suite 1, 848 Boundary Rd, Richlands, Qid, 4077

ACN 129 441890 Fax (07) 33759299 Ph.3363 8181

SOKA Builder *
Bob & Sheryl Hedges

s
Swot N eens PO Box 6354, St Lucia Qld 4067

Project Job No, 9141

Technical Notes

Earth Works Specifications

Batter Angles for Embankments:-

{tis the budders responsibility to ensure that the site works do not undermine or place additional surcharge on any existing structures.
if this can not be achieved STA Consulting Engineers must be contacted prior to any site works being undertaken.

Batter angies must comply with toca! goverment requirements and are to conform as follows {Figure 1).

Figure 1.

Cut Embankment

Lv Fill, H tess than 2.Gm

Material Type Clay

 

Soft Sols

 

{Refer Bore Logs} Firm Clay | Soft Clay

 

 

Embankment Slopes | Compacted Fill : : 1:2 | Norsunabe
(Height Length)

 

 

 

 

 

 

Cutting : : : 1st 2:3

Note: Retaining walls or other forms of soil retaining methods must be adopted where the slope ratio is greater than that
indicated in the table above

Fill Material and Compaction:-

‘Organic material, highly reactive clays and lange racks ara not suitable for use as fill. The fill is to be spread in 1S0mm layers and extensively
track rolled with a drott. All earthworks to be carried out in accortiance with the full requzements of AS3798-1990, Guidelines tor Earthworks for
Commercial and Residential Developments.

Drainage:-

‘The external finished surface surrounding the dwelling must be drained to move surface water away from the buikling and graded to give a stope
of not less than SOmm over the first 1m away from the buikiing.

Reinforcement Specifications

‘Steel wire reinforcing fabric and bars to conform with AS 1304 - Hard Drawn Stee! Wire Reinforcing
Fabric for Concrete} and AS 1302 - Steel Reinforceing Bars For Concrete.

Lap Lengths

Trench Mesh - 500mm in a straight fine, or to the far face at “T” and "L" intersections

Steel Gars - “N" Bars - 35 times the bar diameter.

Corner Bars - sequired at all “T* and “L” intersections. Refer to the design drawings for

the appropriate construction details.

‘Slab Fabric - One full panel of the fabric, so as the two outer-most transverse wires of each sheet
are overlapped. As shown on the below detail (Figure 3).

_2daillonal width, For example a 400mm wide

200 x 100 Eage Square fooling requtan 4 bar tench mash SOG wide,

Concrete Specifications

The concrete must have a strength at 28 days of no! less than 20MP=a unless otherwise specified an tha foundation cross section, a 20mm nominal
aggregate size and have a nominal 60mm slump. Water must not be added to the mix to increase the slump to a value in excess of that specifiad,
Concrete must be placed and compactad/vibrated with good building practice. in hot and windy conditians concrete must be cured dy covering with
plastic sheeting, spraying with e liquid membrane curing campound ef ponding water on the top surface. The concrete must be manufactured to
comaly with AS3600-2001 - Concrete Structures.

Builders Client
NIA
Client Order Number: N/A

 

Used in these records

About this file

File size
2.0 MB (large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

08_1546 - Additional information as requested - Dwelling & retaining Walls [As Published].pdf · 2.0 MB (large file)

The download may take up to a minute.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.