Council archive · source document
001A7F25.001
Text sections not matched to the original PDF pages. See original document to check page numbers.
Semi—Mountable Dowelled expansion NOTES: NOTE: Typical . carpark bay
or Barrier Kerb Transition path joint refer to 1 Crossings are not designed for commercial vehicles. Services & road
and Channe 0 riveway STO dwg SEQ R-065 Footpath section to vary where necessary to match concrete footpaths and furniture will not be
verge profiles. Footpath earthworks coining concrete must be well compacted. =
8 moved for driveways Stormwater 1.0m clear of &
Concrete surface tolerance to be, over 3 metre sections. LATM devices
—Omm
Concrete N32 in accordance with AS 1379 and AS 3600. kerb inlet 1.0m Clearance
| Reinforcement fabric to AS 1304, 50 top and edge cover, lap fabric 250. from pit lintel
Approved materials for construction:— concrete, paving blocks or asphalt,
— t eco refer project drawings.
Ec Expansion joints to be 10mm thick, full depth closed cell cross linked 6.0m 6.0m 6.0m 6.0m
oo polyethylene foam (85 — 150 kg/m), or 10mm thick compressed
oe
a4 + —} + —+ moO granulated corkboard, installation to manufacturers’ instructions. TP TP TP TP
e All appropriate permits must be obtained from Council, including approval of
. “a location and levels prior to excavation.
Nonsip’ topcrete Refer project drawings or local authority standard drawings for verge type
-Q¢
£ ‘ 4 ASA cross sections. 6.0m 6.0m 6.0m 6.0m
2 a ¢ 4 10 One access to be constructed per allotment. eee
co 1 Earthworks cut and fill batters from edge of driveway to natural surface to be
EY EE max. grade at 1 in 10 and fully turfed.
. * Driveways must achieve a high point of 250mm above invert of kerb to ensure
oo 12
oo stormwater is contained within the road reserve as per requirement of QUDM _ 6.0m ACCESS
moO
Ls Alternative 1 profile (Queensland Urban Drainage manual). This constraint may be varied upon the
L 6.0m
approval of the local authority.
Alternative 2 profile 43 Existing footpath to be transitional to new driveway at a maximum grade COLLECTOR
of 1 in 10. Prohibited locations shown in a
1500 14 Under special circimstances Council may approve a rising grade of 1:8 in this heavy line, based on AS 2890.1
1200 min location or within 1 metre of the property boundary. Dimensions are in metres.
15 All dimensions in millimetres.
SPLAYED DRIVEWAY The points marked 'X' are either at the median
Kerb TTT —_——w ee on a divided road, or at the intersection of
Invert A “ the main road centreline and the prolongation
a of the side road kerb line on an undivided road. :
Reinforced SL72 DRIVEWAY_PROHIBITED LOCATIONS
Fabric min.
Sand blinding layer 30 max
SECTION A-A — BREAKOUT TYPE
1000 1000 Roll over
1500
NVERT OF CHANNEL (m) | © Garage/
Carport slab
1500 1500 900
4 in
ty, transition footpath _— |
A Road surface oe @ |= 31 in 8 A in 40 (2.5%) 1 in 20 4 in lin 6 Roll under
» ume in
——_ = 1500
Garage/
Control joint TYPICAL PROFILE DRIVEWAY ACCESS A-A Carport slab
Saw cut existing K&C — 50
min depth at invert — break
out and remove back of K&C These drawings have been developed in consultation between the participating councils.
BEFORE USE, the user shall confirm that the drawing has been adopted by the appropriate council
a
ij INSTITUTE OF PUBLIC WORKS ENGINEERING AUSTRALIA DRIVEWAYS a
CO QUEENSLAND DIVISION INC. RESIDENTIAL DRIVEWAY SEQ R-050F
8
a
At 3708 | ORIGINAL ISSUE _____ STANDARD DRAWINGS BREAKOUT TYPE A
eaeSee the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalUsed in these records
001A7F25.001.pdfRelated documentPublic source context ↗
09/0578 - Operational Works - Landscaping, Carparking, Access, Frontage Works, Stormwater Drainage, Site Civil Works, Sewer & Water Reticulation [As Published]Related documentApplication case desk ↗
About this file
- File size
- 6.9 MB (large file)
- File type
No other editions are linked here.
Original file
Log in to download the original file
The download may take up to a minute.