Original source · versioned page text
200917 La Mer Working Drawings - Rev #
Work in Progress
rev date issued details
client sign-off: date: Working Drawings
#-
WI 20.09.17 MS Working Drawings Rev#
P
1. General Notes 1. General Notes BAL-# BALUSTRADES FLF-# FLOOR FINISH
1.01 All shall be in accordance with the 1.11 All materials, adhesives, applied finishes and BAL-01 Glass Balustrade FLF-01 Exterior Tiles
accompanying drawings and to the other chemical based products such as paint
Frameless glass balustrade panels. Rebated glazing Tiles over reinforced concrete slab in accordance
satisfaction of the Architect. systems should be “0 VOC” unless otherwise with Engineers Documentation. Tiles laid as per
approved by Architect. channel or grout fixed connections to be confirmed
manufacturers specification.
1.02 Figured dimensions take precedence over by glazing contractor. Allow for hydraulic patch
scaled dimensions. Builder to verify on site 1.12 All materials and products incorporated into fitted swing gates where indicated on drawings. Allow for fall to plumbed drainage points as
prior to construction / fabrication. the works shall be fit for purpose and Final set-out to be confirmed with architect required. Refer to Hydraulic Engineer
installed in in accordance with manufacturers
1.03 All ground lines to be confirmed by Builder instructions to comply with warranty Type: T-01
Balustrade to finish 1000mm above finished floor
prior to construction. obligations. Copies of all relevant warranties level min. 1200mm where required for pool
1.04 Building set-out to be by licensed Surveyor, shall be supplied to all contracting parties. compliance. Refer to Architects Drawings for HR-# HANDRAILS
engaged by Builder. 1.13 All timber, including bamboo, must be FSC
finished heights.
HR-01 Handrail
1.05 Refer any discrepancies to the Architect for (Forest Stewardship Council) Certified or
Glass type: Engineered high performance ionoplast Fabricated 32mm diameter min. 316 marine grade
written instruction. recycled. Rainforest timbers are not to be stainless steel handrail, rolled returns and pin fixed
toughened laminated glass (where required).
used. Copper Chrome Arsenic (CCA) treated connections.
Glazing contractor to confirm glass type. Ensure NO
1.06 All work and materials shall be in accordance timber is not to be used. All timber shall be
top handrail or channel is required.
with the Building Code of Australia, the kiln-dried or seasoned (certificates to be Refer to stair detail drawings.
relevant Australian Standards, the applicable provided) unless prior approval of Architect is
Finish: Brushed
codes and regulations of the destination sought.
Glass: Ultra clear low iron
country and local council’s requirements. Any
1.14 All elements specified to be painted or Hardware: 316 Stainless Steel Shop drawings to be provided for approval.
discrepancy or ambiguity shall be referred to
powdercoated are to be in accordance with Finish: PT-03
the Architect for written direction. Must comply with NCC and AS1428.1-2009
Architect’s final colour scheme. Supplier: Euroglass
requirements
Specific attention is drawn to the following Contractor to provide Architect 14 days
notice before the final selections are Glass to comply with AS 1288 and relevant wind REN-# RENDER
elements which must comply with the
required. loadings.
relevant Codes and Standards: REN-01 Render finish 1
- Termite treatment BAL-02 Glass Balustrade
- Stormwater discharge For site painting generally apply 2 finishing Patch fitted frameless glass balustrade panels.Allow
Rockcote Cerano Smooth Set cement render
coats over recommended undercoat System. Allow for acrylic based polymer to match
- Watersaving plumbing fixtures for circular dome head non climbable patch fittings. where required.
- Smoke alarms following appropriate priming of surface. Allow for hydraulic patch fitted swing gates where
- Energy efficiency requirements 1.15 All exposed fixings, plates, screws, nails and indicated on drawings. Final set-out to be confirmed Finish: Smooth Plastic Float - Lightly Burnished
- Bushfire mitigation measures the like to be 316 grade stainless steel where with architect
Colour: Natural Cement
- Insulation appropriate or unless otherwise noted.
Balustrade to finish 1000mm above finished floor
1.07 Any proposed changes to materials, finishes, Structural connections shall be as Engineer’s Allow for water and UV resistant clear matt
level min. 1200mm where required for pool penetrating sealer to manufacturers specifications.
colours etc from those specified must be Drawings. Use dome head or countersunk
compliance. Refer to Architects Drawings for Rockcote Repel.
approved by the Architect PRIOR to fixings (as appropriate) wherever possible.
finished heights.
ordering. Ensure separation of different metals via 3m2 sample to be provided for approval
rubber, neoprene gaskets, sleeves and/or
Glass type: Engineered high performance ionoplast
1.08 The Client recognises that unauthorised silicon joins. REN-02 Render finish 2
toughened laminated glass (where required).
changes to the project are not the
responsibility of the Architect and releases 1.16 Tile edges shall not be exposed. Coordinate Glazing contractor to confirm glass type. Ensure NO Render to match existing.
the Architect from any liability arising from with Architect to select proprietary or top handrail or channel is required.
the construction, use or result of such standard edge trims. Finish: Scratch coat render
Glass: Ultra clear low iron
changes. 1.17 Upon completion, the site is to be Colour: To match existing
Hardware: 316 Stainless Steel
1.09 All work referred to in this schedule is by professionally cleaned for handover. Finish: PT-03
Builder, unless noted otherwise. Work noted 1.18 Completion testing: All plant and equipment Supplier: Euroglass
by “Joiner” or other specialist contractor is is to be tested, commissioned, and adjusted
to be attended upon by the Builder. as required to be in proper running order. Glass to comply with AS 1288 and relevant wind
loadings.
1.10 No material, finish or item used in the project 1.19 Vermin treatment: provide certificates for all
may include any asbestos or hazardous or pest and vermin treatments.
toxic substances or materials.
Sparks Architects Pty Ltd 20200507
a: shop 5, 212 david low way, peregian beach, qld 4573
p: (07) 5471 3033 Alterations and Additions 2 of 7 Sparks Architects Pty Ltd Scale 5 of 7
sparks architects www.sparksarchitects.com
37 Hastings Street, Noosa Heads La Mer Body Corporate 141 MS Materials + Finishes Schedule WD 1.2
sparks architects pty. ltd. abn 89 124 611 721
qld architect's registration No. 3974 project client job no. drawn drawing dwg no.
GSPublisherVersion 166.6.74.18
See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalLog in to download the original file
The download may take up to a minute.