Skip to the record
Accept no substitutions.

Council archive · source document

Part 8 of 37 Appendix 6 - Flood Study MCU12/0208

of 115

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

Very large file (93.6 MB): the whole original can take several minutes to open, especially on a phone. Text is quick to read.

Noosa on Weyba
Flood Study
                                                                                    ~,.,CardnO.

Horizontal data:

Spatial Accuracy: 0.2 @ 67 % CI
The  permanent waterbodies, as shown on aerial photography, of Eenie Creek and Keyser Creek were
manually defined in TUFLOW as minimum z shapes. This was necessary to reduce some triangulation
errors in the OEM which  created false blockages across the waterway and created instabilities in the results.
Similarly other flow blockages in the tributaries, caused by triangulation errors, were removed by inserting
gully lines. The ALS data of the waterway does not penetrate the water surface, and so the storage and flow
capacity below this level is not included. This may result in an overestimation of the minor flood levels.
However, the impact is expected to be negligible for the major flood events.

The grid size used in TUFLOW was 5 metres. This is a grid size typical of urban areas and results in surface
levels at 2.5 metre intervals being used in the modelling.

For the developed case OTM, the earthworks model created in 12d was overlaid onto the existing surface

grid and re-exported.

3.2.3                Roughness Values
The Manning’s n roughness values used in the 10 sections of Lake Weyba and Weyba Creek were kept at
the same values as those used in the Mike 11 modelling. The values varied at different sections but were

typically:

      .     n = 0.025 for   waterway areas; and
      .     n = 0.10 for dense    vegetation.

The Manning’s n roughness values used in the 20 grid were:


      .     n = 0.03 for   waterway areas;
      .     n = 0.12 for de nse   vegetation;
      .     n = 0.20 for urban areas;

      .     n = 0.05 for grass areas with a few trees; and

      .     n = 0.04 for   roadway crossings

A   sensitivity analysis was conducted with a roughness value of 0.15 for dense vegetation areas.          This
resulted in an increase in 100 year ARI peak water levels of around 100 to 150mm along Eenie Creek and
around 50mm along Keyser Creek. The impacts in Keyser Creek were not as great due to the low velocities
in this area.


The roughness values used in TUFLOW are shown in Figure 3.




3.2.4                Model Inflows

The inflows into the TUFLOW model were taken from a WBNM model, which was compared to peak flows

using the Rational Method.           The location of the inflows is shown in Figure 3. The TUFLOW inflows were
either inserted as 20 SA inflows, 20 boundary inflows or 10 inflows. The catchment delineation in the area

surrounding the site was different to that used in the regional flood modelling as there was insufficient detail
in the regional modelling. The developed case inflows were modified as required due to the increase in

impervious area and changes in catchment delineation. Further detail of the WBNM model is given in
Section 4.


For the climate change scenario, the inflows were increased by 20 percent to account for an intensification of
rainfall. This is the amount specified by the Inland Flooding Study (OERM,2010)for the planning year 2090.




Northbrook Corporation Pty Ltd                           Version 1                                23 October 2012
Flood Study v1.doc                                Commercial in Confidence                                Page 4

Used in these records

About this file

File size
93.6 MB (very large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

Part 8 of 37 Appendix 6 - Flood Study MCU12_0208.pdf · 93.6 MB (very large file)

The download may take a few minutes. On mobile data, it is best to wait for Wi-Fi.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.