Original source · versioned page text
Appendix A - Amended Plans
Plans and drawings
This document appears to be plans or drawings. Its page text below holds only the words printed on the drawings, without the drawings themselves, so it may be jumbled or hard to follow. To see the plans as drawn, choose Original above or download the file (both need you to log in).
Log in to see the plans as drawn CONSTRUCTION NOTES
· CONFIRM ALL DIMENSIONS ON SITE TO EXISTING
RESIDENCE PRIOR TO COMMENCEMENT OF ANY Scale 1:100
WORK. 1 0 1 2 3 4 5m
· SUPPLY & INSTALL 'BIFLEX CHEMICAL TERMITE
TREATMENT (UNLESS OTHERWISE APPROVED) TO
COMPLY WITH AS3660.1 AND MANUFACTURER'S boundary line
SPECIFICATIONS ROOF PLAN NOTES
· SELECTED METAL CORRUGATED ROOF
· ALL BRICKWORK (INCLUDING BRICK VENEER), SHALL BE IN
CLADDING TO BE INSTALLED IN ACCORDANCE
ACCORDANCE WITH AS3700-MASONRY CODE
WITH MANUFACTURER'S INSTALLATION
INSTRUCTIONS & AS1562.1 DESIGN &
4,325.
· ALL TIMBER FRAMING SHALL BE IN ACCORDANCE WITH
INSTALLATION OF SHEET ROOF & WALL
AS1684. - UNLESS OTHERWISE APPROVED ROOF
CLADDING - METAL (NCC VOL2 P3.5.1.0(b)).
FRAMING SHALL BE OF TRADITIONAL FRAMED
CONSTRUCTION.
· INSTALL ALL ROOFING COMPONENTS AS PER
MANUFACTURER'S INSTRUCTIONS FOR LHL
· FOR ALL STRUCTURAL MEMBERS, FOOTINGS & LOAD
lower roof lower roof REQUIREMENTS & WIND CLASSIFICATION
BARING WALLS REFER TO STRUCTURAL DOCUMENTATION
building line below REQUIREMENTS.
PREPARED BY ENGINEERS.
·PROPOSED RWDP RAINWATER DOWNPIPE THE
· ELECTRICIAN TO SUPPLY AND INSTALL APPROVED DP DP DP
PROPOSED ROOFING MUST BE INSTALLED TO
DP
HARDWIRED SMOKE ALARMS IN ACCORDANCE WITH
eaves gutter
PREVENT WATER PENETRATION INTO THE
300
DP
DP
DP
AS3786 (NEW LOCATIONS TO BE INDICATED SD) BUILDING STRUCTURE(NCC VOL2 P2.2.2).
eaves gutter
eaves gutter
· ALL ELECTRICAL WORK TO BE CARRIED OUT IN ·WORKERS ARE TO DETERMINE SAFE MANUAL &
ACCORDANCE WITH AS3000. MECHANICAL HANDLING , LIFTING &
eaves gutter INSTALLATION OF ARCHITECTURAL FIXTURES &
· ALL PLUMBING & DRAINAGE WORK TO BE CARRIED OUT COMPONENTS WHILE FOLLOWING WHS
IN ACCORDANCE WITH AS3500. DP INSTRUCTIONS ON MANUFACTURER'S
DOCUMENTATION
450
·ALL SARKING MATERIAL TO BE INSTALLED
ACCORDING TO MANUFACTURER'S
INSTALLATION INSTRUCTIONS & AS/NZS4200
INSTALLATION OF PLIABLE MEMBRANE AND
UNDERLAY (NCC VOL2 P3.5.1(f)) & HAVE A
MAXIMUM 5 FLAMMABILITY INDEX (NCC VOL 2
9,500
P3.7.1.9(a))
450
·CORROSION PROTECTION OF METAL ROOF
SHEETING IS REQUIRED TO MEET WITH MINIMUM
ridge
DP COATING REQUIREMENTS OF MANUFACTURER
eaves gutter existing ·GUTTERS, DOWNPIPES & FLASHINGS
FABRICATED WITH METAL ARE TO MEET AS/
NZS2179 REQUIREMENTS WHILE UPVC
450
metal roof COMPONENTS ARE TO COMPLY WITH AS1273
·NO LEAD ROOFING PRODUCTS ARE SPECIFIED
TO PREVENT TOXINS FROM ENTERING ANY
POTENTIALLY POTABLE RAINWATER
CATCHMENT SUPPLIES (NCC VOL2 P3.5.2.2(d))
·EAVES GUTTERS MUST HAVE A 1:500 MINIMUM
DP
DP
DP
DP
FALL (NCC VOL2 P3.5.2.4(a)(i)) & DESIGNED TO
eaves gutter
ARI20 (NCC VOL2 P3.5.2.3(b)(i))
lower roof ·PROVIDE DEKTITE PIPE FLASHING OR SIMILAR
TO ROOF PIPE PENETRATIONS. INSTALL IN
DP STRICT ACCORDANCE WITH MANUFACTURER'S
300
DP RECOMMENDATIONS, PROVING FREE DRAINAGE
DP
OF WATER FROM AROUND AREAS OF
INSTALLATION
·RECOMMEND BUILDER HAVE CERTIFIED ROOF
ANCHORAGE DESIGN & INSTALLATION TO AS
1891.4 -2000. BUILDING OWNER IS TO ENSURE
7,686
ANNUAL MAINTENANCE & INSPECTION OF
SYSTEM.
6,186
·THE BUILDER IS TO TAKE CARE NOT TO
WIND CLASSIFICATION - N2 CONTAMINATE COLORBOND SURFACES WITH
SUNSCREENS AS THESE HAVE SHOWN TO
REGION B DAMAGE THE SURFACE FINISH PREVAILING
TERRAIN CATEGORY - 3 WEATHER ROOF SHEETS TO BE LAPPED AWAY
FROM PREVAILING WEATHER INGRESS (NCC
TOPOGRAPHIC EFFECT - T0 VOL2 3.5.1.3(d)(iii)(B)
SHEILDING FACTOR - FS
boundary line
NOTE: Job No.
ROOF PLAN
AD21-002
antoniajayne Design ALL DESIGN, CONSTRUCTION & MATERIALS TO BE IN ACCORDANCE WITH:
•THE NATIONAL CONSTRUCTION CODE (NCC)
•THE BUILDING CODE OF AUSTRALIA (BCA) NORTH Issue DEVELOPMENT APPROVAL - client amendments
0409 366 854 •THE QUEENSLAND DEVELOPMENT CODE (QDC)
Rev 06
•BUILDING REGULATIONS & LOCAL GOVERNMENT PLANS & POLICIES
North Booval QLD 4304
[email protected]
•CURRENT ISSUES OF AUSTRALIAN STANDARDS
•CURRENT MANUFACTUERER'S SPECIFICATIONS & INSTALLATION DETAILS AD21-001_13RECTORYSTREET Kate Mayne & Kent Mayne Date 18/2/22
FOR MATERIALS USED
www.ajdesigndp.com ALL DIMENSIONS IN MILLIMETRES UNLESS OTHERWISE NOTED
Page No. A.10
QBCC: 15133061 FOR APPROVAL 13 Rectory Street Pomona QLD 4568
Scale @ A3 1:100
Copyright: This drawings remains the property of antoniajayne Design and is provided for use as noted the recipient(s) of this document is/
are prohibited from disclosing such information, ideas and concepts to any person without prior written consent of the copyright holder. /Users/antoniajayne/Library/Mobile Documents/com~apple~CloudDocs/OBRIEN & DOYLE GROUP_ICLOUD/ANTONIAJAYNEDESIGN_ICLOUD/JOBS/AD21-001_13RECTORYSTREET/ARCHICAD/AD21-001_13RECTORYSTREET_V2.pln Prepared by ANTONIA O'BRIEN
See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalLog in to download the original file
Large file: the download may take up to a minute.
Searchable page text hides email addresses. Original files are unchanged and may show email addresses.