Council archive · source document
Appendix B - Landscape Design Plans · OPW25/0057
Plans and drawings: the text below has words only, no drawings.
Very large file (16.4 MB): may take a few minutes to open.
1 Beveled top as dimensioned
90 190 2 5mm chamfer to all edges
3 Quality rough sawn HWD 90mm x
50 190mm x 1500mm H4 dipped, F14
75
1 1 Beveled top as dimensioned 1 1 CCA preferred (ACQ may be used)
2 5mm chamfer to all edges bollards @ 1500mm centres. Apply 2x
3 Quality rough sawn HWD 90mmx 2 2 coats of clear Tanacoat prior to
190mmx1500mm H4 dipped, F14 installation.
CCA preferred (ACQ may be used) 4 400x500mm deep concrete footing to
bollards @ 1500mm centres. Apply Engineer's specifications.
Top of sleeve to be no greater
3 3
2x coats of clear Tanacoat prior to 5 Drainage layer nominal 10-20mm
than 100mm above FSL
installation. 6 Existing sub-grade
4 400mmØx500mm deep concrete 7 Kerb side
900
2
7 7 8 140x20mm diameter steel rod pin with
825
footing to Engineer's specifications.
5 Post to continue through footing padlock hole face
3 into gravel drainage layer nominal 9 RHS hot dip galvanised section sleeve
10-20mm to fit 90x190mm HWD bollard without
6 Existing sub-grade having to cut bollard
7 Kerb side face 10 300x200x4mm HDG steel base plate
1500
7 8 with 5x20mmØ drainage holes drilled
11 NSC to supply padlock and key
11
F.S.L. F.S.L. F.S.L. F.S.L.
4
9 9
4 4
5 10 10
5 5
6 6 6
Bollard Type X to match specifications noted on Dwg. All timber products to have Forest Stewardship
BL-01 from SCC Open Space Infrastructure Manual Council® (FSC®) Chain of Custody certification
June 2017
All timber products to have Forest Stewardship
Council® (FSC®) Chain of Custody certification
8 BEVELED HARDWOOD BOLLARD - B1 Type 1 9 BEVELED HARDWOOD REMOVABLE BOLLARD - B2 Type 1
L501 Scale 1:10 L501 Scale 1:10
Turf as specified to finish flush with
timber edge. Refer to Turf Profile
Detail.
Planting area to finish flush with
timber edge
Dressed 25x100mm / 38x100mm
Spade cut garden edge
H4 treated (not CCA) hardwood 75°
to be cut at
edge. 5mm chamfer to all edges approximately 75°
fixed with 75mm galvanised batten
angle and run 100mm
screws through pilot hole. deep into soil
100
Treated Timber Stake min. 600mm
x 50mm x 50mm
Existing Subgrade
All timber products to have Forest Stewardship Existing subgrade
Council® (FSC®) Chain of Custody certification
10 MOWING EDGE TYPE 2 - TIMBER EDGING 11 MOWING EDGE TYPE 1 - SPADE CUT
L501 Scale 1:10 L501 Scale 1:10
Approved by: James Oliver (AILA)
Checked - JO Drawing title - Project - Site - Project No. 233467 Sheet No. L601
Design - JO Drawn - JO LANDSCAPE DETAILS Proposed 1 into 3 Development 62 Lake MacDonald Drive, Cooroy
D 24/03/2025 UPDATED PROJECT NAME AR Digital Ref : Issue : D
C 12.03.2025 FOR APPROVAL JO
Scales - AS SHOWN B 24.09.2024 FOR APPROVAL IL 124 DUPORTH AVENUE Ph (07) 5443 7777 Client - This Document is copyright and shall not be copied
PO BOX 16 Fax (07) 5443 7577 without written approval, nor shall it be used except
Document Stage - FOR APPROVAL
A 31.05.2024 PRELIMINARY - FOR COORDINATION ONLY JO
MAROOCHYDORE QLD 4558 Noosa Council for the Development and the Site Specified.
Issue Date Description By E-MAIL: [email protected]
See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalUsed in these records
Appendix B - Landscape Design Plans.pdfRelated documentApplication case desk ↗
About this file
- File size
- 16.4 MB (very large file)
- File type
No other editions are linked here.
Original file
Log in to download the original file
The download may take a few minutes. On mobile data, it is best to wait for Wi-Fi.