Skip to the record
Every meeting, every word.

Council archive · source document

1025JS.lp CDA app ltr · 132003.220735.8

of 5

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

Page 3

PR100133-5.1025JS.Ip

Requested Change:

Amendments are proposed to the ‘Supplementary Table of Development’ to change the Level of
Assessment for Detached Dwellings from Code Assessable to Self Assessable. In addition, it is
proposed to include a new row within this table to allow for Detached Dwellings where not
complying with the key development requirements to be Code Assessable, as shown on revised
Plan No. 6994-53P (Sheet 1).

Key Development Requirements for Precincts table

It is recognised that the ‘Key Development Requirements for Precincts’ table shown on approved
Plan No. 6994-53N is not clear in several respects; it contains minor typographical errors and
requires updating for both administrative and clarification purposes.

We have therefore prepared a concise version of the ‘Key Development Requirements for
Precincts’ table as shown on revised Plan No. 6994-53P (Sheet 1), that replaces the ‘Key
Development Requirements for Precincts’ table shown on approved Plan No. 6994-53 N.

Plan of Development — Inclusion of Sheets 2- 3

It is proposed to include two (2) new sheets within the POD to show building envelopes,
permitted boundary setbacks and built-to-boundary walls. In addition, where built-to-boundary
walls are shown, the opposite side boundary to the built-to-boundary wall boundary shall have a
minimum building setback of 3.0 metres and this is shown on the updated plan sheets. This
requirement is also notated on the amended ‘Key Development Requirements for Precincts’
table under the ‘Built to the Boundary Walls and Side Setbacks’ heading.

Built- to- Boundary Walls for Lots less than 600m?

It is considered that built-to-boundary walls would be a suitable option for lots less than 600m’,
and would significantly improve the streetscape character. Built-to-boundary walls are therefore
provided for, as an option, on all lots less than 600m’.

Development Statistics

Itis proposed to include the word ‘Optional’ before the words ‘Built to boundary line’ in the legend
on the POD. Built-to-boundary walls are considered suitable on lots less than 600m? in area,
however, it is recognised that imposing a mandatory requirement for designated built-to-
boundary wall lots would not always be desirable and it is considered that offering prospective
purchasers this option is more appropriate.

Proposed Lots 63 and 64

Recent discussions with Council’s Planning Officer, Glen Conforti, around our client's request to
change the configuration of proposed Lots 63 and 64, by rotating their common boundary
approximately 90 degrees such that each lot would be afforded two road frontages, indicated that
Council would probably have no objection to such a proposal. The amended configuration of
these two lots is shown on the revised plan, with no other changes to the lot layout proposed.
The new building envelope for each lot allows for a 3.0m setback to both road frontages and a
4.5m side boundary setback in each case, this being consistent with setbacks adopted for other
lots in the development.

Moreover, as each lot will have two road frontages, it would seem to be Council’s preference that
garages gain access from the southern road (Smoke Bush Drive) rather than the northern road
(Hollyhock Crescent) for these two lots. Accordingly, an additional dot point under the ‘General’
heading in the ‘Key Development Requirements for Precincts’ table, specifically provides for this;
our proposed wording is as follows:

“Garage access to Lots 63 and 64 will be from each lot's southern frontage”

1025JS.Ip Permissible Change Ltr

Used in these records

About this file

File size
3.8 MB (large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

1025JS.lp CDA app ltr.pdf · 3.8 MB (large file)

The download may take up to a minute.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.