Change proposal plans · 51983.3225.22

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

     

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE

UNLESS NOTED OTHERWISE, ALL EXISTING
BUILT WORKS ARE TO REMAIN. FOR FURTHER
CLARIFICATION ON EXTENT OF DEMOLITION

NOTES

1. ALL CONSTRUCTION WORK UNDERTAKEN
|S TO COMPLY WITH THE NATIONAL
CONSTRUCTION CODE (BCA), RELEVANT

NOTE:

THESE DRAWINGS ARE DESIGN CONCEPTS
ONLY AND SHALL NOT BE USED IN ANY

WAY FOR STRUCTURAL PURPOSES. REFER

TO STRUCTURAL ENGINEER'S DETAILS

WORKS, REFER TO PROPOSED FLOOR PLAN FOR AUSTRALIAN STANDARDS AND
PROPOSED RECONFIGURATION LAYOUT, WALL APPLICABLE LOCAL AUTHORITY FOR ALL MEMBER SIZES, SPECIFICATIONS
SETOUT DIMENSIONS AND OPENING LOCATIONS. REQUIREMENTS. AND SITE SPECIFIC STRUCTURAL

2, ALL SETBACK/SETOUT DIMENSIONS ARE
TO BE CHECKED AND VERIFIED ON SITE

 

REQUIREMENTS.

 

PRIOR TO CONSTRUCTION.
NOTE:
ROOM DIMENSIONS
N\ SHOWN ARE TO
ADJOINING ADJOINING FINISHED WALL FACES.
VILLA VILLA oq -
ROADWAY
. BOUNDARY ADJOINING LEGEND
_ _ @ - _
VILLA Se
COL STEEL COLUMN
PP N J DP DOWNPIPE
| | - TP TIMBER POST
-w we WASTE PIPE
_ _ _ _ _____EAVES LINE OV@&¥————— >a
| rT <a3 BATHROOM HEATER LIGHT AS SPECIFIED
388
> f SAG oO EXHAUST FAN AS SPECIFIED
= | aa
| 8 | | INO s ° LED DOWNLIGHT AS SPECIFIED
3 ° i oN
| |= = | 8 SMOKE DETECTOR TO LOCAL
5 6 ~ AUTHORITY REQUIREMENTS
ig a | ia
f | \
| | ¥ LOFT ¥ = ) CEILING FAN AS SPECIFIED
5 6485x5315mm (APPROX) 5 < ~
| iS PLASTERBOARD | Z
| 2 =z | a
= , =
sb q | ° ° | NOTE.
| | LIGHTING LAYOUT SHOWN IS NOMINAL.
on) | | BUILDER TO CONFIRM SUITABLE LAYOUT
| | AGAINST ENERGY EFFICIENCY REPORT
7 AND LOCAL AUTHORITY REQUIREMENTS
ADJOINING AND COORDINATE WITH ELECTRICIAN
SS CCEAVESLINEOVER st” ff SHARED
\s— = ——
ADJOINING BOUNDARY ROADWAY
SHARED S BOUNDARY ©
(DEDICATED LOT
ROADWAY EXCLUSIVE USE AREA)

(01. \ REFLECTED CEILING PLAN - LEVEL 3

 

Yo) SCALE 1:100

AN

CRITICAL NOTE: PARTITION WALLS SHOWN ARE BASED ON 70mm WIDE STUD FOR
APPROVAL PURPOSES ONLY. REFER TO STRUCTURAL ENGINEER'S DETAILS FOR ALL
FRAMING SIZING AND STRUCTURAL REQUIREMENTS THROUGHOUT PROPOSED
WORKS. WHERE 90mm STUD FRAMES ARE REQUIRED TO SUIT PROPOSED
STRUCTURE, BUILDER TO MAINTAIN EXTERNAL BUILDING FOOTPRINT AND ADJUST
ROOM SIZES ACCORDINGLY ON INTERNAL SIDE, ENSURING MINIMUM INTERNAL
CIRCULATION WIDTHS ARE MAINTAINED (WHERE REQUIRED). ALL DIMENSIONS
SHOWN ARE FOR APPROVAL PURPOSES ONLY, STRUCTURAL LAYOUT TO BE
CONFIRMED ON SITE BY PROJECT ENGINEER & BUILDER PRIOR TO CONSTRUCTION.

 

NOTES:
4, THIS IS A COMPUTER GENERATED DRAWING. DO NOT AMEND BY HAND.

AMENDMENTS

REV

DATE __DESCRIPTION

 

e FOR APPROVAL

PROJECT

DRAWING CREATED SCALE @A3

2. THIS DRAWING SHOWS DESIGN INTENT ONLY. ALL DIMENSIONS AND AUG 2023 11
SETOUTS ARE TO BE CHECKED ON SITE PRIOR TO ConSTRUCTION | A ]17.08,2023] ISSUE FOR BUILDING APPROVAL G PROPOSED RESIDENTIAL ALTERATIONS 00
3. ANY DISCREPANCIES OR OMISSIONS FOUND WITHIN THE DRAWINGS B | 14.01.2025) PROJECT SCOPE ADJUSTMENTS Ge ‘ADDRESS PROJECTNO. REVISION www.gtgroup.net.au
ARE TO BE REPORTED TO THE DESIGNER PRIOR TO CONSTRUCTION. 22048 B drake A “
4, DONOT SCALE THIS DRAWING. 2/30 HASTINGS STREET, NOOSA HEADS QLD 4567 aes. [email protected]
cr GROUP BULOING DESIGN, THESE DRAWINGS ARE PROTECTED BY [numion cB avin ows. no Ra CSILe
THE LAWS OF COPYRIGHT AND MAY NOT BE COPIED OR REPRODUCED | ORIGINAL SHEET SIZE: A3 (420x297mm REFLECTED CEILING PLAN - LEVEL 3 A112 ODETTE)

 

WITHOUT THE WRITTEN PERMISSION OF GT GROUP BUILDING DESIGN.