Original source · versioned page text
Development Application Part 2 of 2 - Plans and Slope Stability Assessment - OPW13/0022
The original of this document is very large (83.9 MB). Opening the original or downloading it may take a few minutes. Please be patient and don't click again. The page text is quick to read. If you are on mobile data, it is best to wait until you are on Wi-Fi.
Original PDF page 14, section 1. The text section number identifies this passage in the reader.
This document appears to be plans or drawings. Its page text below holds only the words printed on the drawings, without the drawings themselves, so it may be jumbled or hard to follow. To see the plans as drawn, choose Original above or download the file (both need you to log in).
Log in to see the plans as drawn Cardno Bowler Ply Ltd Telephone: Facsimile:
<D BOWLER
Cardno ABN: 74128806735
Address:
54501544
Email:
54501533
[email protected]
32 Hi-Tech Drive, Website: www.cardno.com.au
Shaping the Future Kuna Pari< OLD 4556
QUALITY OF MATERIALS REPORT
Client: Cardno Bowler -
Acacia Ridge Report Number: 3747/R/1856-1
Client Address: 1 Fox Street, Acacia Ridge Project Number: 3747/P/198
Project: Slope Stability, Black Pinch Road Lot Number:
Location: Pomona Report Date: 20/02/2012
Client Reference/s: CBR 10360 Page Number: Page 1 of 1
Test Procedures AS1289.3.6.1, AS1289.3.1.2, AS1289.3.2.1, AS1289.3.4.1,
Sample Number 3747/S/15095 Sample Location
Sampling Method Borehole TP2
Date Sampled 10/02/2012 Termination Depth (m)
Sampled By Client Start Sample Depth (m) 0.4
Date Tested 13/02/2012 End Sample Depth (m) 0.6
Att. Drying Method Cured Material Source -
Atterberg Preparation Air 24 hrs then oven Material Type -
Specification Percent Specification
AS Sieve (mm) PARTICLE SIZE DISTRIBUTION GRAPH
Minimum Passing (%) Maximum
100
19.0 100
90
.L:""_
13.2 100
9.5 99 80
~ -- -
-
6.7 98
# 70
’-oJ
4.75 97 C1 60
e
2.36 90
~ 50
Q.
1.18 85
III
40
0.600 82 I’:!
III
a. 30 --
0.425 80
0.300 79 20 1--------.-- - _.
0.150 77 10 - - " ---_.- _. - - --- - - ---
0.075 75 0
~ 000 !.’" .. 0\ \0 ...... .....r.,)WUl-....J
~ -
- - -
W \O"’--.JWUl
0 - W ,f>. ’" - W --.J --.J Ul - - - - - -
--.J Ul 01\,)0 CX) ’" Ul331\,) OUlUlO 0
Ul 0 o Ul 0 3 3 3 333 333 3 3
3 3 3 3 3 3 3 3. 3 33333
3 3 333
AS Sieve Size (mm)
Specification Specification Specification Specification
Test Result Result Test Result Result
Minimum Maximum Minimum Maximum
Liquid Limit (%) 61 0.075/0.425 Ratio 0.94
Plastic Limit (%) 32 PI x 0.425 Ratio (%) 2320.0
Plastic Index (%) 29 LS x 0.425 Ratio (%) 920.0
Linear Shrinkage (%) 11.5 Linear Shrinkage Defects
R"",k’
I
The results of the tests, calibrations and/or measurements included in this
^
NATA
document are traceable to Australian/national standards
Accredited for compliance with ISO/lEG 17025 D\l
V Laboratory Accreditation Number: 3747 Approved Signatory: David Hammelswang
Form 10: W85Rep Rev 1
See the original
The page text is free to read. Viewing or downloading an original file needs an account.
Log in to see the originalVery large file: the download may take a few minutes. If you are on mobile data, it is best to wait until you are on Wi-Fi.
Searchable page text hides email addresses. Original files are unchanged and may show email addresses.