ADAMS + SPARKES Town Planning Report (30 & 32 The Cockleshell)

 

Part E — Alteration to Existing Water Service

Service

Water Meter Relocation Fee < 1m (wa

ater ir

  
   

r meter and box)
Pe
(This one fee is to retocate or raise a w leler and meter box less than 1m from its original location) 4. $337.00 ea.

(provide existing metermumber;_

   

 

 

 

 

Water Meter Relocation Fee > 1m (water mete
(This is to relocate the water meter and meter b

(provide existing metermumber;__

and box)

als

a $903.00 ea.

   

20x, feft or right, more than

 

 

Convert an Above Ground 20mm/25mm Meter to a Below Ground Meter of Same Size

 

 

 

 

 

 

 

(The water meter will be placed in a meter box)  niasngionms =
Raise or Lower Water Meter Box (box only)

if the water meter needs to be raised to suit box adjustment, one fee only applies, refer to water mater $138.00 ea. oO
relocation fee <1m)
Provide location of service for existing water meter position at property $87.00 ea. oO
Installation of Lockable Ball Valve for Water Meter padiock not supplied) $128.00 ea. a]
Domestic Water Meter Replacement, Calibration and strip Meters (refundable if meter faulty $378.00 ea. oO

 

 

 

 

* A dimensioned Locality Pian clearly showing the preferred location of the new meter location must be attached
* Restoration of concrete surfaces and landscaping is not included in standard fees listed above

* A Marker Peg is to be installed at the property indicating the new meter location

 

Important information for applicant/s applying for installation of a lockable ball valve:
* Before locking your ball valve to off, please check that your water appliances (e.g. hot water systems) are able to be turned off
without harm to the appliance.
* The property owner will be responsible for maintaining the ball valve, the housing and the padlock.
* Ensure that the lockable ball valve and the padiock key are easily accessible in case of fire or other emergency need for water.

Important information for applicants applying for water meter calibration check:
The fee for a water meter calibration check is only refunded if the meter is proved faulty.

 

 

Part F — Sewerage Service

 

 

Where the standard connection criteria cannot be met (refer to Unitywater's Connections Policy) for a sewerage property
connection, the applicant shall lodge an application with Unitywater using the ‘Other and Staged Connection Application (Not for
Standard Connection)’ form, available at http://uni ter.com/Dev: nV/Apopli ns. An application fee will apply for this type
of application.

Where the standard connection criteria is met, and where an alteration to an existing sewer Property connection is sought, the
applicant does not need to proceed with this application and need only submit a Water Supply and Sewerage Services Private
Works Application to Private Works.

For a new sewerage property connection, the applicant must submit a locality plan Clearly showing the dimensioned location,
invert level and surface level of the proposed sewerage property connection and confirm that this controls the subject property in
accordance with the SEQ Code and AS/NZS 3500.

MAPMIATORY CHECK BOX

T___ | confirm the standard connection criteria are met and the dimensioned locality plan with requirements above is attached
with this application.

The applicant must note that following approval for a new sewerage property connection, the applicant will be required to submit a
Water Supply end Sewerage Services Private Works Application to Private Works for Unitywater installation/alteration of the sewer

connection, available at Water Supply and Sewerage Services Private Works Application

A copy of the Unitywater approval and approved service locality plan must be submitted with the Private Works application.
Following payment of the quotation, Unitywater will take approximately 20 working days to install/alter a sewer connection point.

 

Page 3 of 5