Skip to the record
The first. The best. The only NoosaWatch™.

Council archive · source document

0015584F.001

of 69

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

Text sections not matched to the original PDF pages. See original document to check page numbers.

-3-
               penetration may not be practicable and the test is      difficult, but intermediate values (between 1% and 3%)
               discontinued at a reduced penetration.                  would be expected.    Highly organic clays and peats
               In the case where full penetration is obtained with     generally have a friction ratio in excess of 5%.
               successive blow counts for each 150 mm of, say 4,6      Static cone data is recorded in the field on disc for later
               and 7 blows, the record shows,                          presentation using computer aided drafting.
                       4,6,7                       N= 13               The equipment can be operated from any conventional
               In a case where the test is discontinued short of full  drill rig. A total apptied load in the range of 4 to 10
               penetration, say after 15 blows for the first 150 mm    tonnes is required for practical purposes, although
               and 30 blows for the next 40 mm, the record shows:      lighter loads may be used.   The cone penetrometers
                       15, 30/40mm                                     are available with various capacities of cone resistance
              The results of the test can be related empirically to the ranging up   to  100   MPa    for  general   purpose
              engineering properties of the soil.                      investigations, while a range of 0 to 10 MPa can be
              Occasionally, the drop hammer is used to drive 50mm      used where more sensitive investigations of soft clay
              diameter thin walled sample tubes (U50) in clays.   In | are required.
              such circumstances, it is noted on the borehole logs.   The cone resistance value provides a continuous
 @            A modification to the SPT test is where the Same | measure of soil strength or density, and together with
              driving system is used with a solid 60° tipped steel | the friction ratio, provide very useful indications of the
              cone of the same diameter as the SPT hollow sampler. | presence of narrow bands of geotechnically significant
              The solid cone can be continuously driven for some      layers such as thin, soft clay layers or lenses of sand
              distance in soft clays or loose Sands, or may be used | which might otherwise be missed using conventional
              where damage would otherwise occur to the SPT. The      drilling methods.
              results of this Solid SPT are shown as "N." on the      The lithology of the encountered soils is interpreted
              borehole logs, together with the number of blows per    from static cone data and is generally presented on the
              150 mm penetration.                                     static cone log sheets.
              Cone   Penetration Tests - Test Method - Cone | It is important to note that the lithology is interpreted
             Penetration Tests (CPT) are carried out in accordance | information and is based on research by Schmertmann
             with AS 1289 Test 6.5.1-1977, using an electrical | (1970), Sanglerat (1972), Robinson and Campinalli
             friction-cone penetrometer.                             (1986), modified to suit local conditions as indicated by
             The test essentially comprises the measurement of | borehole information and laboratory testing.
             resistance to penetration of a cone of 35.7 mm          As soils generally change gradually it is sometimes
@            diameter pushed into the soil at a rate of 10-20 mm per | difficult to accurately describe  depths  of  strata
             second   by  hydraulic  force.    The  resistance  to   changes, although greater accuracy is obtained with
             penetration is recorded in terms of pressure on the end the static cone compared with conventional drilling. In
             area of the cone (cone resistance, Qc, in MPa) and | addition, friction ratios decrease in accuracy with low
             friction on the side of the    135 mm long sleeve | cone resistance values, and in desiccated soils. As a
             immediately above    the  top of the cone     (friction result, some overlap and minor discrepancies may
             resistance, f;, in kPa). These forces are measured by | exist between   static  cone  and   nearby   borehole
             electrical transducers (strain gauges) within the cone  information.
             device. The ratio between friction resistance and cone | Portable Dynamic Cone Penetrometers - Portable
             resistance is also calculated as a percentage, ie.-    Dynamic Cone Penetrometer (DCP) tests are carried
             Friction Ratio (FR) = eee este rece ls (KPa) x 100     out by driving a rod into the ground with a falling weight
            The friction ratio, FR, is generally low in sands (less hammer and measuring the blows for successive
            than 1% or 2%) and generally higher in clays (say 3%    100mm increments of penetration.
            or more).   The interpretation of sandy clays, clayey
            sands and material with a high silt content is more
            NOTEREP,SAM                                                                SOIL SURVEYS ENGINEERING

Used in these records

About this file

File size
4.1 MB (large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

0015584F.001.pdf · 4.1 MB (large file)

The download may take up to a minute.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.