Skip to the record
The gold standard in government transparency.

Council archive · source document

0015584F.001

of 69

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

Text sections not matched to the original PDF pages. See original document to check page numbers.

.       4.
    The DCP comprises a Cone of 20 mm diameter with | >The use of water or mud as a drilling fluid wit! mask
    30 degree taper attached to steel rods of smaller | any groundwater inflow. Water has to be bailed out of
    section.                                                  the bore and mud must be washed out of the hole or
    The cone end is driven with a 9 kg hammer falling 510 | "reverted" if water observations are to be made.
    mm (AS. 1289 Test 6.3.2).     The test was developed | More reliable measurements can be made by use of
    initially for pavement subgrade investigations,    and    standpipes which are read after stabilizing at periods
    empirical correlations of the test results with California | ranging from several days to perhaps weeks for low
    Bearing Ratio have been published by various Road        permeability soils. Piezometers, sealed in a Particular
    Authorities. The Company has developed their own         Stratum, may be advisable in low permeability soils or
    correlations with  Standard   Penetration   tests  and | where there may be interference from perched water
    Density Index tests in sands.                            tables or surface water.
  LOGS                                                      FILL
   The borehole or test pit logs presented herein are an     The presence of fill materiats can often be determined
   engineering and/or geological interpretation of the       only by the inclusion of foreign objects (eg. bricks,
   subsurface conditions, and their reliability will depend | steel, etc.) or by distinctly unusual colour, texture or @
   to some extent on the frequency of sampling and the | fabric.    Identification of the extent of fill materials will
   method of drilling or excavation.   Ideally, continuous | also depend on investigation methods and frequency.
   undisturbed sampling or core drilling will enable the | Where natural soils similar to those at the site are used
   most reliable assessment but is not always practicable | for fill, it may be difficult with limited testing and
   or possible to justify on economic grounds.     In any   sampling to reliably determine the extent of the fill.
  case, the boreholes or test pits represent only a very | The presence of fill materials is usually regarded with
  small sample of the total subsurface conditions.          caution as the possible variation in density, strength
  The attached explanatory notes define the terms and | and material type is much greater than with natural soil
  symbols used in preparation of the logs.                  deposits. Consequently, there is an increased risk of
  Interpretation of the information shown on the logs, | adverse engineering characteristics or behaviour.      If
  and its application to design and construction, should | the volume and quality of fill is important to a project,
  therefore take into account the Spacing of boreholes or | then frequent test pit excavations are preferable to
  test pits, the method of drilling or excavation, the | boreholes.
  frequency of sampling and testing and the Possibility of | LABORATORY TESTING
  other  than  “straight line" variations  between   the   Laboratory   testing  is  normally   carried  out   in      ©
  boreholes or test pits. Subsurface conditions between    accordance with Australian Standard 1289 "Methods of
 boreholes or test pits may vary significantly from        Testing Soil for Engineering Purposes". Details of the
 conditions encountered at the borehole or test pit | test procedure used are given on the individual report
 locations.                                               forms and the attached explanatory notes summarize
 GROUNDWATER                                              important aspects of the Laboratory Test Procedures
 Where groundwater levels are measured in boreholes, | adopted.
 there are several potential problems.                    ENGINEERING REPORTS
 «Although groundwater may be        present in   lower   Engineering   reports   are  Prepared    by  qualified
 permeability soils, it may enter the hole slowly or | personnel and are based on the information obtained
 perhaps not at all during the time the hole is open.     and on current engineering standards of interpretation
 *A localized perched water table may lead to an | and analysis. Where the report has been Prepared for
erroneous indication of the true water table.            @   specific design   proposal  the   information  and
*Water table levels will vary from time to time with | interpretation   may   not be   relevant if the design
seasons or recent weather changes and may not be | Proposal is changed. If this happens, the Company will
the same at the time of construction,
NOTEREP.SAM                                                                 SOIL SURVEYS ENGINEERING

Used in these records

About this file

File size
4.1 MB (large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

0015584F.001.pdf · 4.1 MB (large file)

The download may take up to a minute.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.