Skip to the record
The first. The best. The only NoosaWatch™.

Council archive · source document

App C - Slope Stability - 14-16 Duke St · 132008.299.02

of 18

Text shows just the words. Original shows the document exactly as it was published.

It should be noted that compaction of such sands as structural fill requires the addition of substantial
volumes of water (‘flooding’) combined with the use of vibratory compaction equipment (typically a
minimum 4 tonne vibrating smooth drum roller or vibrating plate) to achieve required compaction.
Should importation of fill be required, it is recommended that such fill should comply with the following:
   Minimum CBR of 10%
   Maximum plasticity index of 15%
   Shrink-swell index ≤ 1%
   Maximum particle size of 100 mm
Any fill should be compacted at moisture contents within the range of ±2% of optimum moisture
content for Standard Compaction. Select fill should have a maximum particle size of 100 mm for an
uncompacted layer thickness of 200 mm and shall be compacted by repeated rolling with a small
compactor to achieve a dry density ratio of at least 95% of the Standard Maximum Dry Density for
cohesive soils, or 70% Dry Density Index for any imported cohesionless soils.
Confirmatory compaction testing should be carried out at regular intervals. A minimum of two tests per
vertical lift is recommended where structural fill heights are to exceed 300 mm. Further details for
control and testing of fill are given in Australian Standard AS 3798-2007 Guidelines on Earthworks for
Commercial and Residential Developments.
Fill embankment edges must be over-filled by 0.5 the width of the compaction equipment (horizontally)
and then trimmed back to well compacted material.

4.2.3    Excavations
Excavations through loose to medium dense sand should be achievable using conventional earthmoving
plant (e.g. small or larger excavators with toothed buckets). Temporary, unsurcharged cuts could be
formed at 1V:2H in the loose sand, and at 1V:1.5H in medium dense (or denser) sand, for batters up to 3
m in height (where room permits). Flatter batters or temporary retention would be required if
groundwater seepage is encountered or if sloughing of dry sand occurs at the batter surface. Deeper
unretained cuts, if required, should be specifically assessed by Tectonic, unless supported by temporary
retention measures. Unless assessed and approved by a geotechnical RPEQ, all permanent cuts and fills
must be retained.
If the above temporary batter slopes cannot be achieved due to spatial restraints, temporary shoring will
be required (e.g. sheet piles, contiguous piles etc.). Excavations in close proximity to existing
structures/infrastructure will need to be specifically designed to prevent undermining. If undermining is
a potential issue, the existing structures may need to be underpinned or the excavation may require
temporary shoring.
The advice of a suitably qualified and experienced structural RPEQ must be sought regarding any
potential undermining and design and construction of any underpins/temporary shoring (if required).
The above recommendations do not supersede any existing safety regulations or legislation applicable to
excavations (e.g. limits on personnel entry into trenches).
Due to the highly permeable nature of the sands at this site, stormwater is expected to rapidly infiltrate
the ground making un-sealed surface drainage ineffective for the control of flows. Any sealed areas
should be graded to ensure free drainage of stormwater away from construction areas to a control
point(s).



21 October 2025
25317-001-Rev0                                                                                     10 of 13

Used in these records

About this file

File size
4.2 MB (large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

App C - Slope Stability - 14-16 Duke St.pdf · 4.2 MB (large file)

The download may take up to a minute.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.