Skip to the record
NoosaWatch™: The source of truth.

Council archive · source document

09/1382 - Operational Works - Landscaping & Civil Works [As Published] · 142009.1382

of 117

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

Very large file (20.7 MB): the whole original can take several minutes to open, especially on a phone. Text is quick to read.

Unit Bullding. Sunshine Beach
Geatechnical Investigations

Site Classification

The site has been classified for footing design purposes as Class P as defined in AS2870-1996. This
classification is due to the low bearing capacity in the upper soils over part of the site. Footings should
be designed using engineering principles and the data from this report.

Footing System

The footing system adopted will depend on the geometry of the structure on the site, the nature and
distribution of loads and the costs. It is likely that the structure could be Partially on a high level
stiffened raft and partially on a piled footing. Alternatively, the loose soils may be excavated and
recompacted. if recompacted under specified controlled conditions as et out in AS3798-2007, the soils
may be regarded as controlled engineered fill and can be used to support the footing system.

Where a combined footing is proposed, the stiffened raft footing system should be designed as an
equivalent Class M raft as per AS2870 to allow for some differential movement between the piled and
slab on ground components.

Pile foundations typically fall into two categories, namely displacement piles and non-displacement
piles. Displacement piles are those pile types that displace the soil surrounding the pile during
installation, thus effectively improving the ground conditions. Non-displacement piles are those that are
bored into the ground without effectively displacing soil materials, and therefore no improvement i is
obtained from the in situ ground conditions. Examples of non-displacement piles are open bored piles
or continuous-flight auger CFA piles. Screw piers are also a non-displacement type.

Of the pile types indicated above, the displacement piles, CFA piles and screw piers have an advantage
of not requiring pile hole support during construction. Open bored piles may require temporary or
permanent casing to reduce the risk of collapse within the boreholes. Alternate piling types and their
assessed advantages and disadvantages are shown in Table 1 below. Your piling contractor can
provide details of the third piling option, the use of screw piers.

 

 

Table 5: Piles Types and Assessed Advantages and Disadvantages
Pile Type Advantages Disadvantages
Bored Piles. Likely feast expensive option. Additional cost of spoil removal.
Non-displacement Typically lower values of end bearing and
lype Relatively widely available and understood shaft adhesion compared to displacement

piles, due to mode of installation and lower
confidence in pile performance.

Water inflows and consequent wall stability
may complicate construction.

construction technology.

 

Driven Pre-Cast
Concrete Piles.

High level of performance confidence. Relatively high noise and vibration during

 

 

Increased design strength parameters due to

 

installation may affect nearby developments

 

 

‘ i Would require dilapidation studies for
Disp racement displacement type. adjacent structures and vibration monitaring
typ No spoil removal issues. during construction.
Splice joints may be required depending on
depth, increasing cost.
Coffey Geotechnics 3
GEOTKPAR1334AA/A

22 January 2008

Used in these records

About this file

File size
20.7 MB (very large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

09_1382 - Operational Works - Landscaping & Civil Works [As Published].pdf · 20.7 MB (very large file)

The download may take a few minutes. On mobile data, it is best to wait for Wi-Fi.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.