SUPERSEDED Decision Notice - 010.2007.00001022.001 [As Published] · 132007.1022

NOOSA COUNCIL IDAS Development Application Decision Notice                                                       5 of 12

23.   A Waste Management Plan shall be submitted for the demolition to the Environmental Health Section of
      Noosa Council, prior to the development permit for building works being issued. The Plan shall contain the
      following information:-
      MATERIALS ON-SITE                               DESTINATION
                                                      Re-use and Recycling             Disposal
      Expected     waste    Estimated volume (m³)     On-site        *specify   Off-site   *specify   *Specify contractor
      materials                                       proposed    reuse or      contractor       &    & landfill site
                                                      onsite        recycling   recycling outlet
                                                      methods
      Excavation material
      Green waste
      Bricks
      Concrete
      Timber – please
      specify
      Plasterboard
      Metals – please
      specify
      Asbestos
      Other – please
      specify
      NOTE: Details of site area to be used for onsite separation, treatment and storage (including weather
      protection) shall be provided on the plan drawings accompanying your application.

Land Development

River Flooding
24.   All habitable rooms within the proposed buildings on site shall be constructed to comply with Council’s
      Minimum Floor Height requirements as defined in Council’s Planning Scheme and on Council’s Scheme
      Maps at the time of issue of the Building Permit.
      In this regard and as an indication only all habitable rooms within the proposed buildings should have a
      Minimum Floor Height of RL 2.8 (AHD). This level, however, is subject to change and verification shall be
      made to Council’s Land Development Section prior to obtaining a Development Permit for Building Works.
      The applicant should note that compliance with these levels does not necessarily require the site to be
      filled as an equal result can be achieved by suspending the lower levels of the building as opposed to
      filling. To this extent excessive filling should be avoided to prevent any impacts on neighbouring
      properties and minimum floor levels should be strictly adhered to without building higher than is actually
      needed to prevent flooding.

Vehicle Access
25.   A vehicular access driveway to serve Lot 2 on RP65319 shall be constructed from the Gympie Terrace
      frontage of the site with a maximum width of 3.0m and generally in accordance with Drawing Number A-
      02/04 dated 9/07/2007 by JMA Architects.

26.   The driveway shall be designed and constructed to Council’s design standards and to grades that prevent
      vehicles from scraping and/or bottoming whilst also allowing pedestrians movements along the footpath
      without any step or level difference. Should any driveways be constructed to grades that do not comply
      with AS2890.1-2004, Council will require that the driveway be removed and reconstructed to levels that do
      comply.
27.   To ensure pedestrian safety between vehicles exiting the site and pedestrians on the footpath, the
      driveway and any associated fencing or vegetation near the driveway shall comply with the minimum sight
      line requirements as defined in AS2890.1, section 3.2.4. The applicant shall demonstrate compliance by
      illustrating these sight lines on the plans submitted for both Operational Works approval and Building
      Works approval.
28.   All vehicles shall enter and leave the site in a forward direction.
Car Parking
29.   Carparking shall be provided within the site as shown on drawing number A-02/04 dated 9 July 2007 by
      JMA Architects Qld Pty Ltd except as modified herein.

30.   A minimum of 4 covered carpark spaces shall be provided on site.

31.   The carparking area shall be designed to comply with the provisions of AS 2890.1-2004 for user class 1A
      with allowance for vehicles to enter and leave the site in a forward gear and with a minimum head
      clearance (headroom) at any point of 2.2m.




AOP2 c:\docume~1\aop2\locals~1\temp\bcl technologies\easypdf 5\@bcl@10061a81\@[email protected]