Skip to the record
Accept no imitations.

Council archive · source document

Part 6 of 37 Appendix 3 - Geotechnical Assessment MCU12/0208

of 95

Text shows just the words. Original shows the document exactly as it was published.

Check the original when the exact wording matters.

Very large file (49.3 MB): the whole original can take several minutes to open, especially on a phone. Text is quick to read.

                                                                                                                 Noosa on Weyba



The following allowable bearing capacities, as shown in Table 5 below, may be used to assess the footing

pressures that may be applied to the various strata by strip/pad footings without causing bearing capacity
failure.

Table 5: Allowable Bearing Capacities StriplPad footings

                         Material Type                 I    Allowable Base Bearing Capacity (kPa)

  FILL-    Silty/Clayey Sand                                                     NR

  NATURAL           -

                        Very Loose to Loose Sands                                NR

  NATURAL           -
                        Medium Dense Sand                                        100

  NATURAL           -
                        Soft to firm Clays                                       NR

  NATURAL           -
                        Stiff Silty/Sandy Clay                                   100

  NATURAL           -

                        Very stiff or Better Clay                                180

  XW, MUDSTONE                                                                  400

Note: NR        -
                    Not Recommended


If deep level footings are to be adopted to support any of the proposed structures. Alternative deep level

footing types include bored piles, driven timber piles, push piles and screw in steel piles.

Using the Australian Standard AS2159-2009 ’Piling                      -


                                                                           Design and Installation’, the design of a bored pile
foundation system may be based on the following formulae:


           Ed ~ Rd.g


where      Rd,g            =
                                  4>g Rd,ug
           Rd,g            =
                                   Design Geotechnical Strength
           Ed              =
                                  design action effect (design load as the combination of factored loads
                           which produce the most adverse effect on the pile).

           <l>g            =         Geotechnical Reduction Factor

           Rd,ug           =
                                     Design Ultimate Geotechnical Strength
           Rd,ug           =
                                     fs As + fb Ab
           fs              =         Ultimate skin friction pressure

           fb              =         Ultimate base bearing pressure

           Ab              =         Plan area of pile base

           As              =         Surface area of pile


For piles founding into clay or weathered rock:



           fs              =         Sa
           fb              =         S Nc

where      a               =         Adhesion factor

           Nc              =
                                   Bearing capacity factor which varies between 5 and 9 depending on the
                           depth of the pile
           S               =       Undrained shear strength


For piles founding into sands or gravels:



           fs              =
                                     Ks a’   v
                                                 tan

           fb              =
                                     a’vb Nq
where      a’v             =         vertical effective stress at relevant depth

           a’vb            =         vertical effective stress at the base of pile or at limiting depth

           Nq              =
                                     Bearing capacity factor due to overburden pressure
           Ks              =         Earth pressure co-efficient
                           =
                                     Angle of sidewall friction
Prepared for Cardno (Old)                                                                                               Page 15

Used in these records

About this file

File size
49.3 MB (very large file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

Part 6 of 37 Appendix 3 - Geotechnical Assessment MCU12_0208.pdf · 49.3 MB (very large file)

The download may take a few minutes. On mobile data, it is best to wait for Wi-Fi.

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.