Skip to the record
Accept no substitutions.

Council archive · source document

Extension to Currency Period - Approved MCU21 0182 01 {As Published} · MCU21/0182.01

of 18

Text shows just the words. Original shows the document exactly as it was published.

                        a.      All footpath/cycleway must comply with Council’s Standard Drawing SEQ R-065.
                        b.      Provision must be made for disabled access at all kerb crossings associated with
                                pathways, in accordance with Council's current standards.
                        c.      All paths must have a slip resistant surface
                        d.      Expansion and contraction joints must provide a flush finish. Installation of joints
                                by saw cutting is preferred to ensure a smooth ride for cyclists
                        e.      The required work includes any modifications to ensure the footpath finishes flush
                                with all existing service covers and the like, or alternatively these services are
                                raised or altered, so as not to create a pedestrian safety hazard
                        Site Access and Driveways
                 54.    Driveway crossovers must be constructed in accordance with Council’s Standard
                        Drawings RS-049 and RS-050.
                 55.    Any existing unnecessary or redundant property accesses must be removed, and the
                        kerb, footpath and verge area reinstated to match the existing footpath and/or verge
                        treatments. Grassed verge areas to be reinstated must be provided with 100 mm topsoil
                        and grass seed or turf, and must be maintained by the developer until established.
                 56.    The following must be complied with during the construction of the required
                        crossover/driveway:
                        a.      The driveway surfacing must consist of either an approved hot mixed asphaltic
                                concrete or patterned/plain concrete.
                        b.      The driveway must be constructed so as not to concentrate stormwater runoff onto
                                neighbouring properties
                        c.      Underground service conduits for water supply, electricity and any other services
                                must be provided as part of the access driveway
                        d.      Where there is an existing pedestrian path, a matching crossfall must be provided
                                for the driveway on the alignment of the path, for the full width of the path
                        e.      The property access must be located a minimum of 1m clear of existing power
                                poles, streetlights or other signage. The developer is responsible for any
                                necessary relocation of existing services to provide this clearance and must
                                contact the relevant service authorities and comply with their requirements in
                                relation to these works.
                        Earthworks and Retaining Walls
                 57.    All earthworks shall be undertaken in accordance with the provisions of AS 3798
                        Guidelines on Earthworks for Commercial and Residential Development, with
                        geotechnical testing undertaken in accordance with the standard.
                        Stormwater Drainage
                 58.    Appropriate scour protection must be provided at the outlet of all stormwater pipes
                        including temporary outlets.
                 59.    Works associated with this permit must not adversely impact on the existing drainage
                        conditions on other properties (e.g. by blocking or interfering with natural overland
                        flows).
                 60.    Construction of all internal stormwater drainage works must comply with the relevant
                        section/s of Australian Standard AS/NZS 3500.3.




Document Set ID: 23016595
Version: 3, Version Date: 14/05/2024                                                                      Page 9 of 18

Used in these records

About this file

File size
212 KB (small file)
File type
PDF

No other editions are linked here.

Original file

Log in to download the original file

Extension to Currency Period - Approved MCU21 0182 01 {As Published}.pdf · 212 KB (small file)

The supporting record

Open full page ↗

Source document

Analyse documents ↗Open full page ↗

My Comparisons

Choose two to four records of the same kind. Drag using a handle or use the “Compare” buttons.

Your selected records are saved in this browser for your account. Results use the filters on the page where you choose “Compare selected”.